• Korean Journal of Food Science and Technology
• /
• v.20 no.4
• /
• pp.463-469
• /
• 1988

The effects of moisture content and particle size of rice flour on the physical properties of the extrudate were examined by using a autogeneous single screw extruder. The moisture contents tested were in the range of 17-28% and the particle sizes were 18-60mesh and 60-120mesh. Samples were taken at different temperatures from the start-up period to the steady state operation. The expansion ratio increased and bulk density decreased as the moisture content and particle size of the flour decreased. The cutting force decreased and the air cell size became uniform as the moisture content and particle size of the flour decreased. As the moisture content increased, the yellowness of the extrudate powder decreased, while the lightness increased, the apparent viscosity increased and the water soluble index decreased. Gelatinization and partial dextrinization were apparent during the extrusion process, and the degree of dextrinization was appeared to be influenced by the levels of moisture content and particle size of rice flour.

• Journal of the Korea Institute of Building Construction
• /
• v.23 no.3
• /
• pp.241-249
• /
• 2023

The objective of this research was to engineer a tile module that could efficiently curtail the incidence of tile defects during the construction phase. To assess the potential diminution in defect manifestation, we executed experiments centered on surface condition, the variation in mass before and after the freeze-thaw test, and adhesive strength. Our findings demonstrated that thermal contraction and expansion induced a relatively escalated frequency of defects in the underwater setting for the aluminum mesh, while the steel mesh saw a higher defect incidence in the air environment. Additionally, it was noted that the adhesive strength exhibited a trend towards augmentation as the mesh size dwindled. Collectively, these results suggest that the employment of smaller mesh sizes can foster improved adhesive strength, consequently diminishing tile defects. Further exploration and development of the tile module, informed by these insights, can substantially enhance the efficacy of the construction process.

• Korean Journal of Soil Science and Fertilizer
• /
• v.10 no.4
• /
• pp.245-256
• /
• 1978

The effects of different particle size distribution of fused phosphate on the changes of phosphorus content in soil and plant, growth and yield of paddy rice were investigated through pot and field experiments. The following results were obtained. 1. Negative correlation was found between unhulled rice yield and the composition of fused phosphate whose particle size was larger than 28 mesh, and 65 to 150 mesh, and highly significant correlation was found between unhulled rice yield and the composition of fused phosphate whose particle size was 28 to 48 mesh. But no significant correlation was found betweeen unhulled rice yield and the composition of fused phosphate whose particle size was 48 to 65 mesh. Thus the composition of 56% of 28 to 48 mesh particles and 44% of 48 to 65 mesh particles would give the best effect. 2. In the soil of the Jeonbug series rice plant in the plots treated with fine single textured fused phosphate showed poor early growth, i.e. poor tillering and short plant height. But at harvesting stage it showed rather increased number of tillers and higher plant height. Of the composite fused phosphate the more particles of 28 to 48 mesh it had, the better growth it showed. In the soil of the Yesan series rice plant in the treated plots showed much better tillering and higher plant height in contrast with that in the control plots. Of the single textured fused phosphate the finer particles showed better growth, while of the composite fused phosphate the more particles finer than 48 mesh it had, the poorer the tillering. 3. The content of available phosphorus in the soil tended to increase as the particles of both single textured and composite phosphate became finer. The soil phosphorus content decreased as the content of phosphorus absorbed by rice plant increased at each stage of growth, and the amount of soil phophorus decreased became larger as the the particles were finer. The amount of available phosphorus in the treated soils was larger in the soil of the Yesan series than in the soil of the Jeonbug series which was a long cultivated soil and contained relatively high phosphorus. 4. In the single textured fused phosphate the amount of phosphorus absorbed by rice plant tended to increase as the particles were finer, and great difference was found at heading stage, but at harvesting stage little difference was found for all the plots. In the field experiment in the soil of the Jeonbug series more phosphorus was absorbed by rice plant in the plots treated with the composite fused phosphate of higher content of 28 to 48 mesh particles. In the pot experiment the amount of phosphorus absorbed by rice plant was highest in the plots treated with the composite fused phosphate of 53.35% of particles larger than 48 mesh and 46.6% of particles smaller than 48 mesh. In the pot experiment in the Yesan series the amount of absorbed phophorus was highest in the plots treated with the fused phosphate of 47.75% of particles larger than 48 mesh and 50. 216% of particles smaller than 48 mesh. 5. A reverse relationship was found between the absorbed phosphorus and silica. In the pot experiment in the soils of both the Jeonbug and Yesan series the amount of phosphorus absorbed by rice plant increased as the particles were finer, while the amount of absorbed silica tended to decrease.

• Korean Journal of Food Science and Technology
• /
• v.44 no.3
• /
• pp.306-311
• /
• 2012

This study was performed to evaluate the effects on saccharification and alcohol fermentation, according to the size of the ground rice (12, 20, 35 mesh) and ultra sonication process (15, 30, 60, 120 min). After saccharification of the ground rice samples for 3 h at $60^{\circ}C$, sugar content was observed to be high in the order of cooked ground rice (CGR) > ultrasonicated ground rice (UGR) > ground rice (GR), in all sizes of ground rice. Further, higher sugar content was obtained by increasing the time of ultrasonication process. Almost 90% saccharification of CGR ($11.5^{\circ}Bx$) could be reached up to $10.2^{\circ}Bx$ by ultrasonicating 35 mesh ground rice for 120 min. After alcohol fermentation on the 35 mesh saccharified-UGR for 4 days at $25^{\circ}C$, 16.7% alcohol concentration could be obtained, as high as of CGR (17.2%). After 4 days of alcohol fermentation, UGR showed a lower pH and a higher acidity (pH 4.06-4.17, 0.99-1.1%) than CGR (pH 4.27, 0.75%).

• Journal of Adhesion and Interface
• /
• v.6 no.1
• /
• pp.1-6
• /
• 2005

The high accurate simulation of very thin glue layers based on the finite element method is still connected to many problems which result from the necessity to construct a complicated mesh of essentially different sizes of elements. This can lead to a loss of accuracy, unstable calculations and even loss of convergence. However, the implementation of special transmission elements along the glue ling and special edge-elements in the near-edge region would lead to a dramatic decrease of number of finite elements in the mesh and thus, prevent unsatisfactory phenomena in numerical analysis and extensive computation time. The theoretical basis for such special elements is the knowledge about appropriate transmission conditions and the edge effects near the free boundary of the adhesive layer. Therefore, recently proposed so-called non-classical transmission conditions and the behavior near the free edge are investigated in the context of the single-lap tensile-shear test of adhesive technology.

• Journal of the Korean Society of Safety
• /
• v.30 no.4
• /
• pp.20-25
• /
• 2015

In general, the causes of the electrical fire are overcurrent, short circuit, poor contact, etc. This study is aimed to recognize the risk of electric arc to prevent electrical fires due to the conductive dust accumulated on the circuit breaker. The experiment was carried out by the method that conductive metal dust collected from the field is being accumulated on the experimental electrodes with gap of 13 mm until the arc is generated. In case that arc was generated, the amount of conductive dust was measured and the thickness was calculated. This experiments was conducted by particle size. In order to distinguish particle size, mesh size(60~100, 100~150, 150~200, 200~250mesh) was classified using a sieve. As the results of experiment for each of the particle sizes, it was confirmed that there is differences in the generation of arc depending on the thickness of dust accumulated.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.13 no.1
• /
• pp.19-26
• /
• 2009

The response characteristics of $H_2O_2$ monopropellant thrusters at a pulse mode were presented in this paper. A catalyst bed was fixed to $MnO_2$/$Al_2O_3$ to investigate the thruster design effect to response time. Three different thrusters (50 N class) having different injectors, ullage volumes, catalyst grain sizes, and reactor volumes were prepared to investigate the response characteristics. As a result, the ignition delay, pressure rising and tail-off time of case 2-2 thruster with 16-20 mesh catalyst size were 14, 108, 94 ms respectively, which were comparable to requirement of response time at commercial hydrazine thrusters.

• Journal of The Korean Society of Agricultural Engineers
• /
• v.57 no.5
• /
• pp.43-49
• /
• 2015

Most of agricultural structures located in seashore could not avoid rapid deterioration of concrete because chloride-ion and $CO_2$ gradually penetrate into concrete. However, since most of models can be able to describe the phenomenon of penetration by using one or two dimensional models based on finite difference method (FDM), those modes can not simulate the real geometry and it takes a lot of computational time to complete even the calculation. To overcome those weaknesses, three dimensional numerical model considering time dependent variables such as surface concentration of chloride and diffusion coefficient of domain based on finite element method (FEM) was suggested. This model also included the neutralization occurred by the penetration of $CO_2$. Because the model used various sizes of tetrahedral mesh instead of equivalent rectangular mesh, it reduced the computational time to compare with FDM. As this model is based on FEM, it will be easily extended to execute multi-physics simulation including water evaporation and temperature change of concrete.

• The Transactions of the Korean Institute of Electrical Engineers C
• /
• v.54 no.10
• /
• pp.465-470
• /
• 2005

In this paper. an experimental study, for method of increasing the efficiency of electrostatic precipitator for the collection of submicron-sized particles has been studied. All AC electric field was used to induce agglomeration of bipolory charged Particles. .4 bipolar AC-agglomeration system. consisted with a multineedle-mesh discharge system with a control grid, was proposed and investigated. Systematic experiments were carried out to investigate the agglomeration ratio of the AC-agglomeration system as a function of the different grid spacings and grid resistances for the submicron particles generated from liquid prorhane gas burning. The agglomeration ratios, which indicate the particle numbers before and after agglomeration of the test particles in number concentration base, were found to be 0.87, 1.80, 3.86, 9.50 and, 11.00 times for the particle sizes of 0.3. 0.5, 0.7, 1.0, and 2.0$\mu$m at applied voltage of 3.5kV, respectively which showed that the fine particle numbers were decreased while the larger particle numbers were increase greatly.

• Journal of the Korean Society of Food Science and Nutrition
• /
• v.20 no.6
• /
• pp.603-608
• /
• 1991

To improve the utilization of red pepper, the extracting conditions of oleoresin, such as kind of solvents, particle sizes of a sample, sample to solvent ratios, extraction temperatures and times, were studied. Among eight solvents used for oleoresin extraction from red pepper, the optimal solvent was acetone. The most appropriate particle size of red pepper powder, extracting temperature and mixing ratio of red pepper to acetone were 100 mesh, $25^{\circ}C$ and 1 to 3(w/w), respectively. The basis of yield in oleoresin extraction, optimum extracting time was about 5 hours. The yield of oleoresin under the above-mentioned conditions was 18.7%.