• 한국건축시공학회지
• /
• 제22권6호
• /
• pp.565-575
• /
• 2022

최근 디지털 설계기술의 발전에 따라 건축가의 창의성을 극대화한 비정형 설계가 급증하고 있다. 그러나 다양한 비정형 곡면을 구현하기에는 많은 어려움이 발생하고 있다. 비정형 형상구현을 위한 패널분할은 mesh, developable surface, tessellation, subdivision 등의 분할기법이 적용된다. 비정형 패널의 제작 시 이러한 분할기법의 적용과정은 복잡하고 생산데이터 추출에 많은 인력과 시간이 투입된다. 따라서 비정형 건물의 설계 후 패널제작을 위한 생산데이터 추출과정을 빠르고 체계적으로 수행할 수 있는 알고리즘이 필요하다. 이에 본 연구는 빌딩모델, 생산장비 성능, 패턴정보를 종합적으로 고려하여 비정형 패널의 생산데이터 자동생성을 위한 수학적 알고리즘을 제시하는 것을 목적으로 한다. 이를 위해, 패널분할 시 수학적 알고리즘을 제시하였고, 비정형 곡면으로의 Mapping을 통해 CNC 장비를 위한 생산데이터를 추출하였다. 본 연구의 결과는 비정형 콘크리트 패널 생산을 위한 데이터 자동생성을 가능하게 하여 생산성 향상과 원가절감에 기여한다.

• Structural Engineering and Mechanics
• /
• 제90권6호
• /
• pp.611-633
• /
• 2024

This study intends to investigate the response of multi-cell (MC) beams to flexural loads in which the primary reinforcement is composed of both metallic and non-metallic materials. "Multi-cell" describes beam sections with multiple longitudinal voids separated by thin webs. Seven reinforced concrete MC beams measuring 300×200×1800 mm were tested under flexural loadings until failure. Two series of beams are formed, depending on the type of main reinforcement that is being used. A control RC beam with no openings and six MC beams are found in these two series. Series one and two are reinforced with metallic and non-metallic main reinforcement, respectively, in order to maintain a constant reinforcement ratio. The first crack, ultimate load, deflection, ductility index, energy absorption, strain characteristics, crack pattern, and failure mode were among the structural parameters of the beams under investigation that were documented. The primary variables that vary are the kind of reinforcing materials that are utilized, as well as the kind and quantity of mesh layers. The outcomes of this study that looked at the experimental and numerical performance of ferrocement reinforced concrete MC beams are presented in this article. Nonlinear finite element analysis (NLFEA) was performed with ANSYS-16.0 software to demonstrate the behavior of composite MC beams with holes. A parametric study is also carried out to investigate the factors, such as opening size, that can most strongly affect the mechanical behavior of the suggested model. The experimental and numerical results obtained demonstrate that the FE simulations generated an acceptable degree of experimental value estimation. It's also important to demonstrate that, when compared to the control beam, the MC beam reinforced with geogrid mesh (MCGB) decreases its strength capacity by a maximum of 73.33%. In contrast, the minimum strength reduction value of 16.71% is observed in the MC beams reinforced with carbon reinforcing bars (MCCR). The findings of the experiments on MC beams with openings demonstrate that the presence of openings has a significant impact on the behavior of the beams, as there is a decrease in both the ultimate load and maximum deflection.

• 복식문화연구
• /
• 제17권3호
• /
• pp.383-395
• /
• 2009

The purpose of this study was to provide a formative charateristics by analyzing aesthetic charateristics of Egypt costume expressed in contemporary fashion. The result of this study obtained through this process were as follows. Aesthetic characteristics were expressed as a primative-retro characteristics, and a erotic-retro characteristics and a decorative-retro characteristics. Based on these trends, this study analyzed formative charateristics in an aspect of form, color, material, and decoration. In the modern fashion, unlike the H-line silhouette given by a natural fit in the primitive retro, the erotic retro was characterized in the shape by a tight H-line silhouette. For the color, peach, yellow green, gold, light blue, red, and black were used as the main color. For the material, see-through, gauze, mesh, organdy, and tight vinyl were utilized to emphasize an erotic image and expose a body secretly. For the decoration, the characteristic of erotic retro using the simple or same colors frequently was the use of similar accessories colors matched with material colors. The decorative retro was characterized in the shape by a H-line silhouette connected as a part of clothing which applied passium and a greatly modified silhouette from an Egyptian simple style which was well-matched with splendid accessories. For the color, the broadest range of color changes was found from light pastel such as white, yellow, light pink, burnt orange, blue, purple, silver, gold, and red to strong vivid tones. For the material, modern materials such as organdy, tulle, leather, and furs were often used. For the decoration, passium, an eagle pattern, scarab earrings, a crown, a sneak-shaped coronet, and pictograph printed on the fabric were frequently used.

• 한국의상디자인학회지
• /
• 제20권2호
• /
• pp.31-46
• /
• 2018

This study was carried out to offer basic data that can be used for outdoor wear production for active senior males, emerging as a new consumer bracket in the era of rapid aging. To this end, this study modified and complemented the patterns of outdoor jackets for active senior males based on existing outdoor jackets that received the most excellent evaluation. On the basis of the research outdoor wear wearing assessment results, this study confirmed those areas to be modified and proposed areas to be considered in manufacturing outdoor wear for this demographic. As a result of existing outdoor wear's wearing assessment, the jacket of brand B was shown to be the most excellent one. This study actually designed research outdoor wear patterns by modifying the problematic parts through the addition and subtraction of spare length or circumference in the sections where fit satisfaction was low by referring to the selected brands' patterns. The research outdoor wear was designed by referring to the preferred outdoor types and colors that were highlighted in the previous survey result of consumer wearing reality, based on the designs of the outdoor wear receiving the most excellent assessment in wearing assessment. Fabric that specially glued two-layered mesh that bonded the thin membrane of synthetic resin with polyester fabric was used as the material in this study. Wearing assessment was conducted by comparing the manufactured research outdoor wear and the existing outdoor wear selected as excellently assessed outdoor wear. Consequently, this study verified that the wearing fit of the research outdoor wear was more excellent in most items. This study proposed final patterns for outdoor jackets suitable for active senior males through the modification of several items that required improvements as per the wearing assessment of the research outdoor wear.

• 대한치과보철학회지
• /
• 제43권6호
• /
• pp.727-735
• /
• 2005

Statement of problem. Platform switching in implant prosthesis has been used for esthetic and biological purpose. But there are few reports for this concept. Purpose. The purpose of this study is evaluation of platform switching in wide implant by three dimensional finite element analysis. Materials and Methods. The single implant and prosthesis was modeled in accordance with the geometric designs for Osstem implant system. Three-dimensional finite element models were developed for (1) a wide diameter 3i type titanium implant 5 mm in diameter, 13 mm in length with wide cemented abutment, titanium alloy abutment screw, and prosthesis (2) a wide diameter 3i type titanium implant 5 mm in diameter, 13 mm in length with regular cemented abutment, titanium alloy abutment screw and prosthesis(platform switching) was made for finite element analysis. The abutment screws were subjected to a tightening torque of 30 Ncm. The amount of preload was hypothesized to 650N, and round and flat type prostheses were loaded to 200 N. Four loading offset point (0, 2, 4, 6 mm from the center of the implants) were evaluated. Models were processed by the software programs HyperMesh and ANSA. The PAM-CRASH 2G simulation software was used for analysis of stress. The PAM-VIEW and HyperView were used for post processing. Results. The results from experiment were as follows; 1. von Mises stress value is increased in order of bone, abutment, implant and abutment screw. 2. von Mises stress of abutment screw is lower when platform switching. 3. von Mises stress of implant is lower when platform switching until loading offset 4 mm. 4. von Mises stress of abutment is similar between each other. 5. von Mises stress of bone is slightly higher when platform switching. Conclusion. The von Mises stress pattern of implant components is favor when platform switch ing but slightly higher in bone stress distribution than use of wide abutment. The research about stress distribution is essential for investigation of the cortical bone loss.

• 한국해안해양공학회지
• /
• 제4권1호
• /
• pp.45-58
• /
• 1992

황해 및 동중국해에서 기상학적으로 유발된 연여균 및 계절적 해류 순환을 산정하기 위해 3次元 수치모형이 이용되었는데 수치모형은 불규칙한 연안경계와 실제 수심을 반영할 수 있도록 구성되었다. 본 연구에서는 전회의 동중국해의 3차원 수치모형 (Choi, 1984)을 제붕역에서의 흐름을 좀더 자세히 재현할 수 있도록 세분화하였는데 모형에 사용된 유한격자체계의 해상도는 위도 4분과 경도 5분으로 구성되었으며 황해 및 동중국해상에서 유속의 3차원적 순환 형태가 산정되어 제시되었다. 수치모형에 의해 계산된 기상학적으로 유발된 恒流 유원은 이 해역의 여러 영역에서 수심(표면, 중간수심, 바닥)別 및 전체 水柱에 대해 해수 문체시간을 계산하는데 이용되었다.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 1996년도 춘계학술대회논문집; 부산수산대학교, 10 May 1996
• /
• pp.263-270
• /
• 1996

본 연구에서는 여러개의 원판형 압전소자가 부착된 판구조물의 소음제어를 다루었다. 판재의 아래에는 소음원이 위치하고 이 소음원은 판재를 가진한다. 구조물 및 압전소자는 3차원 요소, 구조물 요소 및 천이요소의 조화로 이루어지는 유한요소로 모델링 되었다. 최적화 과정의 목적함수는 구조물로부터 복사되는 소음 에너지이고 설계변수는 원판형 압전소자의 위치, 크기 및 인가되는 전압이 사용되었다. 최적설계과정에서 요구되는 자동격자형성이 언급되었다. 구조물의 공진 및 비공진 주파수에서 최적설계가 행해졌으며 괄목할 만한 소음감소를 얻었다. 이 결고는 음향 하중의 형태가 다르게 변하더라도 크게 변하지 않는 것이 밝혀졌다. 또한 한 주파수 뿐 아니라 넓은 주파수 영역에서도 압전가진기의 전압을 조정함으로써 좋은감소를 얻을 수 있다.

• 한국의학물리학회지:의학물리
• /
• 제9권3호
• /
• pp.143-154
• /
• 1998

상강화기는 형광 영상장치에서 영상의 특성을 결정하는 주된 요소이다. 본 연구는 두가지의 상강화기를 임상에서 평가하기 위하여 간단하고 비파괴적이며 적당한 시간내에 행할 수 있는 계의 활동 프로그램을 제시하였다. 이 프로그램은 크게 세 부분 즉, X-선 발생장치, 영상의 질, 조준으로 되어있다. X-선의 발생장치에 대하여 관전압의 정확도와 자동노출 조절기능을 비교하였다. 영상의 질을 위해서는 저대비 및 고대비 분해능 측정, 체격자 실험 등을 수행하였으며 이 실험에서는 비디오 모니터 및 순간영상을 필름화한 정량적인 분석을 분석하였다. 조준에 대해서는 상강화기의 유용한 영역의 직경과 상의 찌그러짐을 측정하고 정량적인 분석을 하였다. 이 실험들의 과정 및 결과들이 상강화기의 인수검사 및 계의 활동지수를 평가하는데 이용되기를 바란다.

• 한국자동차공학회논문집
• /
• 제22권1호
• /
• pp.117-125
• /
• 2014

The temperature distribution of steady state rolling tires with detailed tread blocks is numerically predicted using the three dimensional full patterned tire model. A three dimensional periodic patterned tire model is constructed by copying 1-sector mesh in the circumferential direction. Using the static tire contact analysis, the strain cycles during one revolution are approximated with the strains at Guassian points of the elements which are sector-wise repeated within the same circular ring of elements, by neglecting the tire rolling effect. Based upon the multi-axial fatigue theory, the maximum principal strain is used to represent the combined effect of six strain components on the hysteretic loss. In the following, the deformation due to the inflation and vertical load is calculated using ABAQUS. Then heat generation rate in each element is calculated using an in-house code. Lastly, temperature distribution is calculated using ABAQUS again. Through the numerical experiments, the validity of the proposed prediction method is examined by comparing with the experiment and the temperature distribution of a patterned tire model is compared with those of the main-grooved simple tire model.

• Journal of Pharmaceutical Investigation
• /
• 제23권3호spc1호
• /
• pp.9-18
• /
• 1993

Sugar spheres loaded with melatonin (MT) were coated with $Aquacoat^{\circledR}$ to control the release rate of MT over 8 hours. A zero-order release pattern over 8 hours was obtained with 20% coating on 8-10 mesh beads in USP basket dissolution studies. MT in 20% coated beads was quite stable at room temperature with less than 5% MT degraded during 6 months' storage. Dissolution profiles were also unchanged after 6 months. An oral preparation containing MT-loaded uncoated beads for immediate release and 20% coated beads with $Aquacoat^{\circledR}$ for controlled release over 8 hours was evaluated in six human subjects. When total 0.5 mg MT as low dose (immediate release portion of MT, 0.1 mg) was administered to four subjects, average peak plasma MT concentration was reached at about 600 pg/ml and maintained at about 10 pg/ml over 8 hours. Plasma MT concentration-time profiles were similar in shape to computer-simulated profiles. However, maximal plasma MT concentrations were three times greater compared to computer simulated curve. These results suggest that MT dose, ratio of immediate and controlled release MT, and pharmacokinetic parameters selected are adjusted to mimic endogenous MT concentration-time curve. In another study, 0.2 mg MT having 10% of immediate release portion and 80% controlled release portion produced plasma MT concentration-time curve which is more similar to endogenous profiles. A low bioavailability (<20%) may result from extensive first pass metabolism and remaining amounts of MT from controlled beads. A good correlation between plasma MT concentration and urinary excretion rate of 6-sulphatoxymelatonin (6-STMT), a major metabolite of MT was observed. As plasma MT concentration increased, urinary excretion rate of 6-STMT increased concomitantly. The linear relation between plasma MT and urinary excretion rate of 6-STMT was statistically significant. This result suggests that urinary 6-STMT may be used as an index of circadian rhythms of MT in humans.