• 한국구조물진단유지관리공학회 논문집
• /
• 제21권4호
• /
• pp.116-123
• /
• 2017

본 연구는 음의 포아송비 거동을 가지는 격자체의 구조부재 보강재로의 적용이 가능한지에 대한 검토를 수행하였다. 콘크리트를 포함한 일반적인 재료는 외부 하중의 작용 시 양의 포아송비 거동을 가진다. 이러한 콘크리트의 역학적 거동을 음의 포아송비 특성을 가지는 금속 격자체가 구속함으로써 콘크리트의 강성을 증대시킬 수 있음을 이론적으로 확인하였다. 또한 실제 건설산업에 적용이 가능한 수준의 음의 포아송비 거동을 가지는 격자체의 형식을 제시, 역학적 거동 특성을 수치 해석적으로 검토하였다.

• IEIE Transactions on Smart Processing and Computing
• /
• 제4권4호
• /
• pp.224-230
• /
• 2015

This manuscript presents a real-time solution for 3D human body reconstruction with multiple RGB-D cameras. The proposed system uses four consumer RGB/Depth (RGB-D) cameras, each located at approximately $90^{\circ}$ from the next camera around a freely moving human body. A single mesh is constructed from the captured point clouds by iteratively removing the estimated overlapping regions from the boundary. A cell-based mesh construction algorithm is developed, recovering the 3D shape from various conditions, considering the direction of the camera and the mesh boundary. The proposed algorithm also allows problematic holes and/or occluded regions to be recovered from another view. Finally, calibrated RGB data is merged with the constructed mesh so it can be viewed from an arbitrary direction. The proposed algorithm is implemented with general-purpose computation on graphics processing unit (GPGPU) for real-time processing owing to its suitability for parallel processing.

• 한국건축시공학회:학술대회논문집
• /
• 한국건축시공학회 2009년도 춘계 학술논문 발표대회 학계
• /
• pp.213-217
• /
• 2009

Underground structures are built into concrete like a architecture and public works. Concrete has watertightness as such, But buildings are leaking from the cracks. Recently, construction method do a lot of close construction in the downtown area. So architects are using the method for the outer layer of a two-layer wall to save spaces. They have been using Top-down method and waterproof agent method and others to outer layer of a two-layer wall method. But, There are many leakage in underground structure from lack on requirements performance of materials. Therefore, I hope to test the outside Waterproof Method of Ground using Wire-mesh and Non-hardening Viscosity Waterproof. In addition to, I wish to apply as outside waterproof method for the section for the outer layer of a two-layer wall in underground structure.

• 한국건축시공학회:학술대회논문집
• /
• 한국건축시공학회 2007년도 춘계학술논문 발표대회
• /
• pp.133-136
• /
• 2007

It has been applied the self adhesion waterproofing sheet which is developed from exist asphalt waterproofing sheet by heat and torch in domestic construction field. However, the problem of waterproofing have constantly happened due to air pocket condition and defect of joint part in waterproofing construction. Therefore, in this study, we would like to analyze the field application as testing in side of materials and construction method of self adhesion butyl rubber sheet and study of the materials performance.

• 한국전산구조공학회:학술대회논문집
• /
• 한국전산구조공학회 1998년도 봄 학술발표회 논문집
• /
• pp.60-67
• /
• 1998

This paper deals with the development of a variable-node element and its application to the adaptive h-version mesh refinement-recovery for the incompressible viscous flow analysis. The element which has variable mid-side nodes can be used in generating the transition zone between the refined and unrefined elements and efficiently used for construction of a refined mesh without generating distorted elements. A modified Gaussian quadrature is needed to evaluate the element matrices due to the discontinuity of derivatives of the shape functions used for the element. The penalty function method which can reduce the number of independent variables is adopted for the purpose of computational efficiency and the selective reduced integration is carried out for the convection and pressure terms to preserve the stability of solution. For the economical analysis of transient problems, not only the mesh refinement but also the mesh recovery is needed. The numerical examples show that the optimal mesh for the finite element analysis of a wind around the structures can be obtained automatically by the proposed scheme.

• International Journal of Safety
• /
• 제8권2호
• /
• pp.20-25
• /
• 2009

In this study, an experiment in the field was performed to analyze the mechanical properties and the influence of steel fiber and silica fume on the rebound ratios of shotcrete. The experimental parameters which are the reinforcing methods (steel fiber, wire mesh), steel fiber contents (0.0%, 0.5%, 0.75%, 1.0%), silica fume contents (0.0%, 10.0%), layer thickness (60 mm, 80 mm, 100 mm), and the placing parts (sidewall, shoulder, crown) were chosen. From the mechanical test, it was found that the flexural strength and toughness is significantly improved by the steel fiber and/or silica fume. According to the results for the side wall in this test, the larger the fiber contents are in case of steel fiber reinforced shotcrete, the less the rebound ratios are within the range of 20-35%, compared to the wire mesh reinforced shotcrte. And also, the reduced rebound ratios were very larger in using steel fiber reinforced shotcrete with silica fume content of 10%, and these results are true of the shoulder and the crown. respectively.

• 청정기술
• /
• 제7권1호
• /
• pp.81-88
• /
• 2001

발전소의 탈황에 사용되는 습식탈황장치에는 반응제로 석회석이 사용된다. 본 연구에서는 주로 사용되는 325mesh입도의 석회석과 함께, 저렴한 200mesh석회석의 탈황공정 특성에 관하여 조사하였다. 석회석의 용해도에 대해 입도별로 실험한 결과 석회석의 입도가 클수록 용해속도가 떨어지는 것을 알 수 있었다. 그러나 습식탈황 공정에서의 탈황율은 석회석 입도와는 상관없이 L/G비(Liquid/Gas ratio, $L/m^3$) 및 현탁액의 pH에 의해서 증감되었다. 탈황공정에서의 부산물로 발생하는 석고의 경우에는 입도가 작아짐에 따라, 그리고 pH가 낮아짐에 따라 순도는 향상되는 것으로 나타났다. 한편 두 가지 입도의 석회석을 일정분율씩 혼합하여 실험한 결과 그 혼합비에 비례하여 탈황율, 석고 순도, 석회석 이용율 등의 공정특성이 나타났다.

• 한국건축시공학회지
• /
• 제23권3호
• /
• pp.241-249
• /
• 2023

본 연구에서는 타일 하자 저감을 위해 시공 프로세스를 보완한 타일 모듈을 제작하였다. 타일 모듈은 떠붙임 시멘트 모르타르, 메쉬, 콘크리트로 구성되었다. 하자 발생 저감 가능성을 검토하기 위해 동결융해 시험 전후의 표면상태와 질량 변화율 실험을 실시하였으며 부착강도를 측정하였다. 그 결과, 알루미늄(A) 메쉬는 수중 환경에서, 강철(S) 메쉬는 기중 환경에서 열수축-팽창에 의한 하자가 상대적으로 다수 발생하였고, 메쉬의 크기가 작을수록 부착강도가 상승하는 경향을 보였다.

• 대한기계학회논문집A
• /
• 제20권2호
• /
• pp.553-563
• /
• 1996

An algorithm for automatic mesh generation of two-dimensional arbitrary planar domain is proposed by using Delaunay triangulation algorithm. An efficient algorithm is proposed for the construction of Delaunay triangulation algorithm over convex planar domain. From the definition of boundary, boundary nodes are first defined and then interior nodes are generated ensuring the Delaunay property. These interior nodes and the boundary nodes are then linked up together to produce a valid triangular mesh for any finite element analysis. Through the various example, it is found that high-quality triangular element meshes are obtained by Delaunay algorithm, showing the robustness of the current method. The proposed mesh generation scheme has been extended to automatic remeshing, which is applicable to FE analysis including large deformation and large distortion of elements.

• 한국기계가공학회지
• /
• 제2권4호
• /
• pp.61-66
• /
• 2003

An excellent mesh construction is of Importance in yielding good results of finite element analysis. The new mesh generation algorithm, which offsets boundaries inward, was developed on the basis of a looping method. An user interface technique and automatic splitting lines which both divide a given domain into subdomains manually or automatically, were used. In addition, the separation method has advantages to prevent the large scale of element size and to control numbers of nodes and elements. This new mesh generation algorithm was proved in practice.