• 대한용접접합학회:학술대회논문집
• /
• 대한용접접합학회 2002년도 Proceedings of the International Welding/Joining Conference-Korea
• /
• pp.791-797
• /
• 2002

This paper introduces the partial melting process for solder application and characterization of its feasibility using Sn-Ag, and Sn-Cu solder alloys. ill order to show that the liquid phase in the semi-liquid state maintains the similar wettability as single-phase liquid, the wetting balance tests are conducted with varying temperatures and compositions. Also, as a new soldering technology, the microstructural and mechanical test were investigated. The results from this research indicate that the partial melting can yield satisfactory sider joints as long as the liquid phase acquires sufficient chemical activity. At a condition where the partial melting is effective, a direct correlation between the wettability and the surface tension is found to exist.

• 한국에너지공학회:학술대회논문집
• /
• 한국에너지공학회 1998년도 추계 학술발표회 논문집
• /
• pp.126-133
• /
• 1998

• 마이크로전자및패키징학회지
• /
• 제7권2호
• /
• pp.63-68
• /
• 2000

This paper introduces the partial melting process for solder application and characterization of its possibility using off-eutectic Pb-Sn alloy. In order to show that the liquid phase in the semi-liquid state maintains the wettability as the single-phase liquid, the wetting balance test are conducted with varying temperatures and compositions. The results are then compared with the surface tension of liquid, both measured and calculated, to examine the correlation. The results from this investigation indicate that the partial melting can yield satisfactory solder joints as long as the liquid phase acquires sufficient chemical activity. At a condition where the partial melting is effective, a direct correlation between the wettability and the surface tension is found to exist. All alloys are found to show a reasonable wettability in semi-liquid state.

• 소성∙가공
• /
• 제20권2호
• /
• pp.118-123
• /
• 2011

Manufacturing of the bipolar plate of a direct methanol fuel cell (DMFC) by direct laser melting technology (DLM) was attempted. The DLM technology is highly influenced by process parameters such as laser power, scan rate and layering height. Therefore, an analysis of the DLM technology was performed under various conditions. The bipolar plates were fabricated using the DLM process with 316L stainless steel (STS 316L) plates and powder. Powder melting trials at various energy density were performed in order to select a feasible melting range for a given laser power. The melting line height increases and eventually saturates when the energy density increases, but decreases when the laser power increases at a given energy density. For the estimation of the potential performance of the bipolar plate, the surface roughness and contact resistance of the DLM layer were also analyzed. The changes of line height and thickness are useful information to report when manufacturing bipolar plate of fuel cell through the DLM process.

• Journal of Pharmaceutical Investigation
• /
• 제37권1호
• /
• pp.1-5
• /
• 2007

Solid dispersions of piroxicam were prepared by melting method using poloxamer as a carrier. The results of DSC and XRD studies showed that the amorphous farm of piroxicam coexisted with the crystalline form in the solid dispersions. However, the ratio of crystalline form of piroxicam in the solid dispersion prepared by melting method decreased in comparison with the same ratio of the solid dispersion prepared by solvent method. As the ratio of poloxamer in the solid dispersion increased, the ratio of the amorphous form of piroxicam in the solid dispersion increased. The dissolution rate of piroxicam from the solid dispersions was significantly higher than that from piroxicam powder. In comparison to the solid dispersion prepared by solvent method, the dissolution rate of piroxicam from the solid dispersion prepared by melting method was higher. As the ratio of poloxamer in the solid dispersion prepared by melting method increased, the initial dissolution rate decreased, however, the total amount dissolved at the end of the study increased.

• Composites Research
• /
• 제23권3호
• /
• pp.43-49
• /
• 2010

제주도 표선리 현무암 원광을 이용하여 연속 방사에 의해 현무암 섬유를 제조하였다. 먼저 현무암의 용융특성을 확인하기 위하여 현무암 원광을 백금도가니에 넣고 $1550^{\circ}C$로 용융시킨 후, 물속에서 급냉하였다. 냉각한 후 X-선 회절, 열팽창, 고온 점도, 고온 전기전도도와 고온 현미경을 측정 분석하여 연속방사 조건을 조사하였다. 연속 섬유를 제조하기 위한 최적의 방사 온도와 고온 점도는 각각 $1264^{\circ}C$와 $10^{2.8}$ poise이었다. 제조된 방사 섬유의 특성은 인장강도, 전자현미경 관찰, 내열시험 등으로 확인하였다. 부싱 온도 $1240^{\circ}C$와 와인더 속도 4600rpm의 방사 조건에서 제조된 섬유의 인장 강도는 3660MPa을 나타내었다.

• 대한기계학회논문집A
• /
• 제36권10호
• /
• pp.1241-1248
• /
• 2012

본 연구의 목적은 CW 레이저 조사에 의한 실리콘 웨이퍼의 손상을 평가하는 것이다. 먼저, 레이저 조사에 의한 온도 및 응력 변화를 3 차원 유한요소해석 모델을 이용하여 예측하였다. 해석 결과, 93 $W/cm^2$의 레이저 빔이 조사되었을 때, 실리콘 웨이퍼의 표면의 응력은 약 140 MPa 까지 증가하였으며 균열이 발생할 것으로 예측되었다. 레이저 강도가 더욱 증가하여 186 $W/cm^2$ 일 때에는 실리콘 웨이퍼의 표면의 온도는 $1432^{\circ}C$까지 증가하였으며 표면부가 용융될 것으로 예상되었다. 실험 결과, 102 $W/cm^2$ 의 레이저 빔이 실리콘 웨이퍼 표면에 조사되었을 때 표면부에 균열이 발생하였고, 레이저 빔의 강도가 더욱 증가하여 140 $W/cm^2$ 일때 표면부에서 용융이 발생하였다. 용융이 발생하는 레이저 빔의 강도는 유한요소해석 결과보다 낮은 값이었으며 이는 표면부에서 생성된 균열에 의해 레이저 빔의 다중반사와 다중흡수가 일어나 레이저 빔의 흡수량이 증가하였기 때문이다.

• 한국결정성장학회지
• /
• 제17권3호
• /
• pp.108-112
• /
• 2007

광원에 따라 색상이 변화하는 cubic zirconia 단결정을 skull melting 법으로 성장하였다. Co와 Nd에 의해서 황색 영역의 강한 흡수가 일어나며, Fe에 의해 보라색 영역의 흡수가 일어남에 따라 광원이 형광등에서 백열등으로 변화할 때 청-녹색에서 적-자색으로 변화가 발생한다. 첨가물에 의해서 뿐만 아니라 yttria 함량과 열처리 조건 변화에 의해서도 결정의 색이 변화하였다.

• Applied Microscopy
• /
• 제50권
• /
• pp.12.1-12.11
• /
• 2020

Hot stage microscopy (HSM) is a thermal analysis technique that combines the best properties of thermal analysis and microscopy. HSM is rapidly gaining interest in pharmaceuticals as well as in other fields as a regular characterization technique. In pharmaceuticals HSM is used to support differential scanning calorimetry (DSC) and thermo-gravimetric analysis (TGA) observations and to detect small changes in the sample that may be missed by DSC and TGA during a thermal experiment. Study of various physical and chemical properties such sample morphology, crystalline nature, polymorphism, desolvation, miscibility, melting, solid state transitions and incompatibility between various pharmaceutical compounds can be carried out using HSM. HSM is also widely used to screen cocrystals, excipients and polymers for solid dispersions. With the advancements in research methodologies, it is now possible to use HSM in conjunction with other characterization techniques such as Fourier transform infrared spectroscopy (FTIR), DSC, Raman spectroscopy, scanning electron microscopy (SEM) which may have additional benefits over traditional characterization techniques for rapid and comprehensive solid state characterization.

• 보존과학연구
• /
• 통권21호
• /
• pp.57-75
• /
• 2000

We performed the scientific analysis through composition analysis, micro-structure investigation, melting point and hardness test to the glass beads excavated at Naesanri in Gosung. Through this investigation, we could examine closely the characterization of raw materials and manufacture technique As a result of micro-structure investigation of glass beads, it appeared that the bubbles in glass beads have remained. Coloring agents of yellow glass bead was remained to the shape of inclusion. And on observing the transparent solid particle, we can know that these do not melt the raw materials because of low melting temperature of a crucible. The result of composition analysis of all glass beads using ICP, these were classified as $Na_2O_2$-$SiO_2$ type of glass. Also, these added to $AI_2O_3$ to improve the durability. The value of Vickers hardness of glass beads appeared the HV 490-530. The HV 1,440 of the transparent solid particle was much more than that of inner glass bead. This means that raw materials do not melt because of a low melting temperature of a crucible. The result of melting temperature analysis of glass beads using DSC/TGA, it was measured about $1,250^{\circ}C$.