• Journal of Chest Surgery
• /
• v.6 no.1
• /
• pp.15-22
• /
• 1973

The definition of cancer, its diagnosis and its prognosis all depend upon description of growth. To the layman a synonym for cancer is a "growth". There are no quantitative terms for the description of growth or growth rate in clinical use. There has been no attempt to assign values that would define "rapidly" or "slowly" growing. Estimates of growth potentiality are implied in the descriptive phrases "poorly differentiated" or "well differentiated", "highly malignant" or "low grade malignancy". and in systems of grading. These qualifying terms represent a personal impression, clinically useful in prognosis, but relative in nature. They do not lend themselves to uniform application or precise measurement for purpose of comparison. Growth is related to size and time. The volume of tumor depends upon the duration of the period of growth and the rate of growth. If the interval and change in volume are known. the average growth rate can be determined. If the growth rate is determined, and assumed to be constant., the duration of a given tumor and the time of inception can be estimated. The commonest concept of the origin of cancer is that as a result of a mutation involving a single cell, succeeding divisions of cells establish a colony with the characteristics recognizable as cancer. If the growth rate of the hypothetical tumor were constant it could be described in terms of "tumor volume doubling time". In the department of thoracic surgery of St. Mary hospital in Catholic Medical College, a clinical evaluation for the growth rate, degree of malignancy, resectability and prognosis was done on a total 24 cases of primary bronchogenic carcinoma which contour was significant on the chest X-ray film as possible estimating the tumor volume doubling time. The following results were obtained: 1. In the cases of 6.0cm or more in diameter of minor size at operation the resectability rate was lower and in the cases of 60 days or more in the tumor or volume doubling time the resectability rate was higher. 2. If differentiation of cancer cells was lower graded in tissue pathology, the tumor volume was shorter and the resectability rate was lower. 3. The tumor volume doubling time of the primary bronchogenic carcinoma occured more over 60 years of age was slightly shorter than under 60 years of age. 4. The tumor size at operation was more important to evaluate the survival time and prognosis than the tumor volume doubling time because the tumor growth was not always constant, we presume.mor volume doubling time because the tumor growth was not always constant, we presume.

• Asian Pacific Journal of Cancer Prevention
• /
• v.17 no.1
• /
• pp.65-71
• /
• 2016

Although high mammographic density is one of the strongest predictors of breast cancer risk, X-ray based mammography cannot be performed before the recommended screening age, especially not in adolescents and young women. Therefore, new techniques for breast density measurement are of interest. In this pilot study in Guam and Hawaii, we evaluated a radiation-free, bioimpedance device called Electrical Breast Densitometer$^{TM}$ (EBD; senoSENSE Medical Systems, Inc., Ontario, Canada) for measuring breast density in 95 women aged 31-82 years and 41 girls aged 8-18 years. Percent density (PD) was estimated in the women's most recent mammogram using a computer-assisted method. Correlation coefficients and linear regression were applied for statistical analysis. In adult women, mean EBD and PD values of the left and right breasts were $230{\pm}52$ and $226{\pm}50{\Omega}$ and $23.7{\pm}15.1$ and $24.2{\pm}15.2%$, respectively. The EBD measurements were inversely correlated with PD ($r_{Spearman}=-0.52$, p<0.0001); the correlation was stronger in Caucasians ($r_{Spearman}=-0.70$, p<0.0001) than Asians ($r_{Spearman}=-0.54$, p<0.01) and Native Hawaiian/Chamorro/Pacific Islanders ($r_{Spearman}=-0.34$, p=0.06). Using 4 categories of PD (<10, 10-25, 26-50, 51-75%), the respective mean EBD values were $256{\pm}32$, $249{\pm}41$, $202{\pm}46$, and $178{\pm}43{\Omega}$ (p<0.0001). In girls, the mean EBD values in the left and right breast were $148{\pm}40$ and $155{\pm}54{\Omega}$; EBD values decreased from Tanner stages 1 to 4 ($204{\pm}14$, $154{\pm}79$, $136{\pm}43$, and $119{\pm}16{\Omega}$ for stages 1-4, respectively) but were higher at Tanner stage 5 ($165{\pm}30{\Omega}$). With further development, this bioimpedance method may allow for investigations of breast development among adolescent, as well as assessment of breast cancer risk early in life and in populations without access to mammography.

• Asian Pacific Journal of Cancer Prevention
• /
• v.16 no.14
• /
• pp.6111-6116
• /
• 2015

Background: Stomach cancer is one of leading causes of death worldwide. In Thailand, the incidence and mortality of stomach cancer are in the top ten for cancers. Effects of DNA repair gene X-ray repair cross complementary protein 1 (XRCC1) polymorphisms and clinicopathological characteristics on survival of stomach cancer in Thailand have not been previously reported. The aim of this study was to investigate the effects of XRCC1 gene and clinicopathological characteristics on survival of stomach cancer patients in Thailand. Materials and Methods: Data and blood samples were collected from 101 newly diagnosed stomach cancer cases pathologically confirmed and recruited during 2002 to 2006 and followed-up for vital status until 31 October 2012. Genotype analysis was performed using real-time PCR-HRM. The data were analyzed using the Kaplan-Meier method to yield cumulative survival curve, log-rank test to assess statistical difference of survival and Cox proportional hazard models to estimate adjusted hazard ratio. Results: The total followed-up times were 2,070 person-months, and the mortality rate was 4.3 per 100 person-months. The median survival time after diagnosis was 8.07 months. The cumulative 1-, 3-, 5-years survival rates were 40.4%, 15.2 % and 10.1 % respectively. After adjustment, tumour stage were associated with an increased risk of death (p= 0.036). The XRCC1 Gln339Arg, Arg/Arg homozygote was also associated with increased risk but statistically this was non-significant. Conclusions: In addition to tumour stage, which is an important prognostic factor affecting to the survival of stomach cancer patients, the genetic variant Gln339Arg in XRCC1 may non-significantly contribute to risk of stomach cancer death among Thai people. Larger studies with different populations are need to verify ours findings.

• Journal of Acupuncture Research
• /
• v.19 no.2
• /
• pp.189-200
• /
• 2002

Objective : This study is designed to find out the effects of Carthmi-Flos herbal acupuncture theraphy on knee joint with osteoarthritis. Methods : 32 cases of diagnostic patient with the osteoarthritis of knee joints by biochemical method, X-ray analysis and hematologic & serologic tests are divided Carthmi-Flos herbal acupuncture theraphy Group(HAG, 16 peples) and non-Carthmi-Flos herbal acupuncture theraphy Group(NHAG, 16 peoples) at Ik-San Oriental medical hospital in wonkwang university from 1th June 2000 to 31th January 2002. After treatment, we evaluated the effect per each group . Results : 1. In the both HAG and NHAG females were much more than males. Sixty aged patients were the most in the HAG(56.3%) and Seventy aged patients were the most in the NHAG(68.8%). 2. Over 5 years duration of disease in HAG was the most(37.5%). 6 months and over 5 years duration of disease in NHAG was the most(each 31.3%). 3. Two groups were not improved chronic stage(over 5 years). 4. The effect of treatment by condition of patients was follows: After treatment, Grade IV & III were decreased 75.0% in HAG and 56.2% in NHAG 5. In the distribution of treatment progression : 15 cases(93.7%) were recoverd in HAG but 14 cases(87.5%) in NHAG. 6. After comparing the results before and after treatment, we found 93.3% of patients showed recovery at anterior area and 88.9% showed at posterior. Conclusion : These results shows that Carthmi-Flos(CF) herbal acupuncture treatment has good effect on osteoarthritis in knee joint. Futhermore it is possible that CF acupuncture is one of the promising candidates for long-term therapy of osteoarthritis.

• Korean Journal of Digital Imaging in Medicine
• /
• v.11 no.2
• /
• pp.115-119
• /
• 2009

I think this will be valuable reference for assuring consistency and homogeneity of clarity and managing dental radiation equipment by experimentation of dental radiation equipment permanent which based on KS C IEC 61223-3-4 standard and KS C IEC 61223-2-7. Put a dental radiation generator and experiment equipment as source and film(sensor) length within 30 em, place the step-wedge above the film(sensor). Tie up tube voltage 60 kVp, tube current 7 mA and then get an each image through CCD sensor and film by changing the exposure time as 0.12sec, 0.25sec, 0.4sec. Repeat the test 5times as a same method. Measure the concentration of each stage of film image, which gained by experiment, using photometer. And the image that gained by CCD sensor, analyze the pixel value's change by using image J, which is analyzing image program provided by NIH(National Institutes of Health). In case of film, while 0.12sec and 0.25sec show regular rising pattern of density gap as exposure time's increase, 0.4sec shows low rather than 0.12sec and 0.25sec. In case of CCD sensor density test, the result shows opposite pattern of film. This makes me think that pixels of CCD's sensor can have 0~255 value but it becomes saturation if the value is over 255. The way that getting clear reception during decreasing human's exposed radiation is one of maintaining an equipment as a best condition. So we should keeping a dental radiation equipment's condition steadily through cyclic permanent test after factor examination. Even digital equipment doesn't maintain a permanent, it can maintain a clarity by post processing of image so that hard to set it as standard of permanent test. Therefore it would be more increase the accuracy that compare a film as standard image. Thus I consider it will be an important measurement to care for dental radiation equipment and warrant homogeneity, consistency of dental image's clarity through comparing pattern which is the result from factor test against cyclic permanent test.

• Journal of Trauma and Injury
• /
• v.25 no.4
• /
• pp.217-222
• /
• 2012

Purpose: Diaphragmatic rupture following trauma is often an associated and missed injury. This report is about our experience with treating traumatic diaphragmatic rupture (TDR). Methods: From January 2007 to September 2012, 18 patients who had a diaphragmatic rupture due to blunt trauma or penetrating injury underwent an operation for diaphragmatic rupture at our hospital. We retrospectively reviewed their medical records, including demographic factors, initial vital signs, associated injuries, interval between trauma and diagnosis, injured side of the diaphragm, diagnostic tools, surgical method or approaches, operative time, herniated organs, complications, and mortality. Results: The average age of the patients was 43 years, and 16 patients were male. Causes of trauma included motor vehicle crashes (n=7), falls (n=7), and stab wounds (n=5). The TDR was right-sided in 6 patients and left-sided in 12. The diagnosis was made by using a chest X-ray (n=3), and thorax or upper abdominal computed tomography (n=15). Ten(10) patients were diagnosed within 12 hours. A thoracotomy was performed in 8 patients, a video-assisted thoracoscopic surgery in 4 patients, a laparotomy in 3 patients, and a sternotomy in one patient. Herniated organs were the omentum (n=11), stomach (n=8), spleen and colon (n=6), and liver (n=6). Eighteen diaphragmatic injuries were repaired primarily. Seven patients underwent ventilator care, and two of them had pneumonia and acute respiratory distress syndrome. There were no operative mortalities. Conclusion: Early diagnosis and surgical treatment determine the successful management of TDR with or without the herniation of abdominal organs. The surgical approach to TDR is chosen based on accompanying organ injuries and the injured side.

• Journal of the Korean Society of Radiology
• /
• v.14 no.1
• /
• pp.45-51
• /
• 2020

The purpose of this study was to analyze the educational effect of self-directed learning method using 3D printed anatomy on radiological science students. The subjects were 32 students (20 males and 12 females) in the second year of radiological science at university. They were divided two groups as a non-active student group and an active student group. A learning method was self-directed learning using 3D printed anatomical structures, and the effects of quantitative learning improvement were evaluated before and after the learning. The qualitative evaluation of the students was analyzed on the Likert's 5-point scale for the interest, satisfaction, and learning effects (memorization convenience of anatomy name, radiography Interpret ability, understanding on bones structure, and X-ray projection technique). As a result, the enhancement of learning improved 65.4% on average, and all students got scored high on all variables. Especially non-active student groups showed higher correlation coefficients in all variables except interest and radiography interpret than active student groups. These results might suggest that self-directed learning using 3D printed anatomical structures could have a positive educational effect on radiological science students.

• Journal of the Korean Society of Radiology
• /
• v.11 no.3
• /
• pp.161-169
• /
• 2017

The cone beam computed tomography(CBCT) which can acquire 3-dimensions images is widely used for confirmation of patient position before radiation therapy. In this study, through the simulation using the Monte Carlo technique, we will analyze the exposure dose by cone beam computed tomography and present the standardized data. For the experiment, MCNPX(ver. 2.5.0) was used and the photon beam spectrum was analyzed after Cone beam was simulated. As a result of analyzing the photon beam spectrum, the average energy ranged from 25.7 to 37.6 keV at the tube voltage of 80 ~ 120 kVp and the characteristic X-ray energy was 9, 60, 68 and 70 keV. As a result of using the water phantom, the percentage depth dose was measured, and the maximum dose appeared on the surface and decreased with depth. The absorbed dose also decreased as the depth increased. The absorbed dose of the whole phantom was 9.7 ~ 18.7 mGy. This is a dose which accounts for 0.2% of about 10 Gy, which is generally used for radiation therapy per week, which is not expected to have a significant effect on the treatment effect. However, it should not be overlooked even if it is small compared with prescription dose.

• Journal of Biomedical Engineering Research
• /
• v.24 no.5
• /
• pp.381-389
• /
• 2003

Various adult diseases (cerebral apoplexy, athymiait, etc.) result from hypertension, blood circulation disturbance and increment of HBP. In early diagnosis of these diseases, MRI, X-ray and PET have been used rather aim for treatment than for a prevention of disease. Since. cerebral apoplexy and athymiait could appear to the regular/irregular persons, it is very important to measure HBP which has connection with cerebral blood flow state. HBP has more diagnosis elements than that of BP. So, we can diagnose accurate hypertension by measuring of HBP. But, existing sphygmomanometers and automatic BP monitors can not measure HBP, and can not execute complex function(measuring of BP/HBP, blood flow improvement). Purpose of this paper is to develop a system and algorithm which can measure BP/HBP for accurate diagnosis. Also, we extracted diagnosis factors by correlativity analysis of BP/HBP. Maximum pressure of HBP corresponds to 62% that of BP, Minimum pressure of HBP corresponds to 46% that of BP. Therefore, we developed the multi-function automatic blood pressure monitor which can measure BP/HBP and improve cerebral blood flow state.

• Journal of Biomedical Engineering Research
• /
• v.24 no.3
• /
• pp.203-208
• /
• 2003

The effect of indium on the microstructure and hardness of a Au-Pt-Cu ternary alloy was investigated using optical microscopy, differential scanning calorimeter, scanning electron microscopy x-ray diffractometry, electron probe microanalizer and vickers hardness tester. A hardness of the solution floated Au-Pt-Cu-0.5In quarternary alloy with 0.5 wt.% was reached a maximum value (162 Hv) in 30 min at 550$^{\circ}C$ in the range of 150 to 950$^{\circ}C$ but that of the alloy was rapidly increased until 30 min with increasing aging time at 550$^{\circ}C$ and after that was remained almost constant value. Also, the microhardness of the matrix Au-Pt-Cu ternary alloy aged at 550$^{\circ}C$ for 30 min was continuously increased with indium contents and the grain size of Au-Pt-Cu ternary alloy decreased as increased indium contents. Analyses of EPMA and XRD revealed that the matrix Au-Pt-Cu-In quarternary alloy is composed of fcc structure and intermetallic InPt$_3$ precipitate with Ll$_2$ structure. Based on this investigation, it can be concluded that an increase in microhardness of Au-Pt-Cu-In quarternary alloy is due to precipitation hardening InPt$_3$ and grain size refinement.