• Journal of the Microelectronics and Packaging Society
• /
• v.21 no.1
• /
• pp.41-44
• /
• 2014

We employed UV-Ozone treatment method for the fabrication of dense and highly conductive nanoparticle thin films. We demonstrated the UV-Ozone treatment effect on the silver nanoparticle thin films as a function of time and temperature. The capping layers of nanoparticles were decomposed after UV-Ozone treatment and dense nanoparticle thin films were obtained. Moreover, electrical and mechanical properties of the thin films after UV-Ozone treatment were measured by using resistance measurements under tension in an in-situ tensile tester. The initial resistance of nanoparticle thin films was decreased by 82.6% with optimized UV-Ozone treatment condition of $150^{\circ}C$ for 20 minutes.

• Journal of Korea Foundry Society
• /
• v.29 no.6
• /
• pp.251-256
• /
• 2009

The effect of austempering treatment on mechanical properties of nodular indefinite chilled iron(NICI) and ductile cast iron(DCI) was investigated. In microstructural observation, matrix phase(pearlite and ferrite) was changed to ausferrite after austempering treatment both DCI and NICI. In case of NICI, decomposition of cementite($Fe_3C$) during austempering treatment was induced. After austempering treatment, mechanical properties such as hardness, tensile strength and impact toughness was improved in NICI and DCI. The wear resistance is slightly decreased because of decomposition of cementite during austempering treatment in NICI but impact toughness and strength is dramatically increased.

• Fashion & Textile Research Journal
• /
• v.3 no.2
• /
• pp.174-179
• /
• 2001

This study investigated the effect of aftertreatments such as using the softener or starch on the mechanical properties of knitted fabrics. The mechanical properties of fabrics, hand value(HV) and total hand value(THV) were measured and calculated by the KES-F system. The main results are as follows: The values of tensile energy(WT), coefficient of friction(MIU) and geometrical roughness(SMD) were increased by softener but decreased by starch treatment. However, the values of tensile linearity(LT), bending(B, 2HB), thickness(T) and weight(W) were increased by starch but decreased by softener treatment. Tensile resilience(RT) was increased not only by softener but also by starch treatment. It showed that the levels of FUKURAMI, NUMERI and SOFUTOSA were increased by the treatment of softener and the levels of KOSHI and SHARI were increased by the treatment of starch. Total hand value(THV) was lower in fabric with starch treatment than fabric with none treatment.

• Journal of the Korea Institute of Military Science and Technology
• /
• v.24 no.2
• /
• pp.197-203
• /
• 2021

Mechanical structures of military equipment have been mainly applied with black oxide coating due to the limitation of surface treatment thickness. However, the mechanical structures applied by the black oxide coating treatment is constantly being corroded by calcium chloride and humidity. Since this can cause serious problems in the operation of equipment, a review to improve surface treatment and corrosion resistance is required. Therefore, in this study, surface treatment methods that can enhance corrosion resistance were selected and corrosion resistance performance was verified through experiments describing harsh field conditions. Thus, applying a proven surface treatment method to future military equipment will prevent corrosion.

• Journal of the Korean Society for Heat Treatment
• /
• v.16 no.6
• /
• pp.341-348
• /
• 2003

Superalloys which can be devided into three categohes, i.e. Ni-base, Co-base, and Fe-base alloys are widely used for high temperature applications. Since superalloys contain many alloying elements and precipitates, its chemistry and processing parameters need to be carefully designed. In this review, current state-of-the art in the superalloy technologies is described with special attention to the heat-treatment for the control of the microstructures and mechanical properties.

• Journal of the Korean Society for Heat Treatment
• /
• v.23 no.6
• /
• pp.301-308
• /
• 2010

A steel with chemical composition, 0.22% C, 0.25% Si, 1.26% Mn, 0.22% Cr, 0.04% Ti, 0.0042% B, and a microstructure of ferrite and spheroidized cementite has been press-formed to automotive center pillar followed by local-hardening heat-treatment. Hardness, tensile properties, fractography, microstructure and surface roughness of local-hardening heat-treated automotive center pillar have been examined. The directly heated and quenched area had fully martensitic structure with Vickers hardenss in the range of 500 to 510. The heat affected area close to the directly heated area showed dual-phase structure of ferrite and martensite. The width of the heat-treated and heat-affected areas after the local-hardening heat treatment was ranging from 32 mm to 50 mm. The surface of the local-hardening heat-treated center pillar revealed some temper color as a consequence of the oxidation during the heat treatment, but the surface roughness was not affected by the local-hardening heat treatment.

• Composites Research
• /
• v.35 no.6
• /
• pp.463-468
• /
• 2022

The high porosity of the infill pattern of carbon chopped fiber-reinforced Nylon composite structures fabricated by the fused filament fabrication (FFF) type 3D printers determines the mechanical performance of the printed structures. This study experimentally evaluated the mechanical performance of Onyx composite specimens fabricated with a rectangular infill structure under the hot-pressing condition to improve the mechanical properties by reducing the porosity of the infill pattern of the printed structure, and evaluated the best mechanical performance. The hot-pressing conditions (145℃, 4 MPa, 12 min) that induce the most appropriate mechanical properties were found. As a result of microscopic observation, it was confirmed that the infill porosity of the composite specimens subjected to post hot-pressing treatment was effectively reduced. In order to confirm the mechanical performance of the post-treated specimen, a tensile test and a three-point bending test were performed with a control specimen without post-treatment and a specimen printed with the same density and dimensions after post-treatment to evaluate the mechanical properties. As a result of comparison, it was confirmed that the mechanical properties were effectively improved when the post-treatment of hot-pressing was performed.

• Journal of the Korean Society for Heat Treatment
• /
• v.3 no.1
• /
• pp.25-33
• /
• 1990

Recently developed austempered ductile irons(A.D.I.) have good mechanical properties. However it is still needed to examine the relationships between microstructures related to banitic reaction and the mechanical properties. From the mechanical tests such as impact test, hardness test, tensile test, and the microstructure observations, we concluded that the good mechanical properties of A.D.I. came from the fine banitic ferrite structure formed during the first stage of the austempering reaction.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.37 no.4 s.112
• /
• pp.18-25
• /
• 2005

The mechanical strength is the prime requisite for linerboard and corrugating mediums. Repeatedly recycled OCC fibers show less suitable property for papermaking mostly due to hornification and reduced fiber length. To overcome these problems many researches including fractionation, enzymatic treatment, and chemical or mechanical treatments of fibers have been carried out. In this study, the effect of mechanical treatment by high consistency pulping on the characteristics of recycled fibers as well as mechanical properties of sheets were investigated. Results on the strength properties of handsheets made of recycled fibers that were treated to same freeness level by beating and high consistency pulping, respectively, showed that beating treatment was more efficient in improving strength. Drainage and recycling potential of the fibers treated by high consistency pulping, however, were expected to be superior to beating because fines content and fiber length didn't change significantly.

• Journal of Sericultural and Entomological Science
• /
• v.44 no.2
• /
• pp.82-86
• /
• 2002

Silk sericin powder was prepared by mechanical treatment from culled-cocoon extract of Bombyx mori silkworm. The physical and structural characteristics of sericin powder were investigated by instrumental analysis. The solubility of sericin powder was decreased nearly half of sericin lyophilized. Amino acid analysis showed that arginine content was decreased from 3.72% to 0.03∼0.07%. XRD showed that molecules of sericin were somewhat regularly arranged by mechanical treatment. On the other hand, FT-IR showed the molecular vibration of silk sericin was not induced by mechanical treatment. Thermal properties also did not changed.