• Advanced Composite Materials
• /
• 제16권4호
• /
• pp.283-298
• /
• 2007

Environment-friendly composites reinforced with bagasse fiber (BF), a kind of natural fiber as the remains from squeezed sugarcane, were fabricated by injection molding and press molding. As appropriate matrices for injection molding and press molding, polypropylene (PP) and polycaprolactone-cornstarch (PCL-C) were selected, as a typical recyclable resin and biodegradable resin, respectively. The mechanical properties of BF/PP composites were investigated in view of fiber mass fraction and injection molding conditions. And the mechanical properties and the biodegradation of BF/PCL composites were also evaluated. In the case of injection molding, the flexural modulus increased with an increase in fiber mass fraction, and the mechanical properties decreased with an increase in cylinder temperature due to the thermal degradation of BF. The optimum conditions increasing the flexural properties and the impact strength were $90^{\circ}C$ mold temperature, 30 s injection interval, and in the range of 165 to $185^{\circ}C$ cylinder temperature. On the other hand, as to BF/PCL-C fully-green composites, both the flexural properties and the impact strength increased with an increase in fiber mass fraction. It is considered that the BF compressed during preparation could result in the enhancement in mechanical properties. The results of the biodegradability test showed the addition of BF caused the acceleration of weight loss, which increased further with increasing fiber content. This reveals that the addition and the quantities of BF could promote the biodegradation of fully-green composites.

• 한국생산제조학회지
• /
• 제22권3호
• /
• pp.356-363
• /
• 2013

Mechanical molding press which is used for transformation process during semiconductor manufacturing process has structural deformations by pressure. If these deformations have over limit range, life of the press itself can be reduced and it will be exerted on a bad effect for quality of the semiconductor. In this research, the main plates and links of a press are analyzed in relation to the structural deformations caused by pressure excluding thermal deformations. After modifying the modeling, the analysis is performed again to determine optimal design of the press, and this design is introduced to ensure that most of the stresses on the main plates are within safe allowable limits. As a result, an optimal design method for the structure is investigated to produce the desired pressure even when the size of the main structure is minimized.

• 한국해양공학회:학술대회논문집
• /
• 한국해양공학회 2000년도 추계학술대회 논문집
• /
• pp.171-177
• /
• 2000

It is essential to understand the creep behavior, which shows how long the characteristics of material maintains because press joined molding GMT-Sheet for recycle is usually used in the severe environment. In this study, we predict joining strength of GMT-Sheet for recycle, when lap length was changed. and we will investigate how compression ratio have an effect on creep behavior in press joined molding. The result of experiment of forming condition concerned with joining problem of GMT-Sheet is as followings joining efficiency. of GMT-Sheet, increases as lap joint length I, increases. Increase of compression ratio causes decrease o f joining efficiency after of GMT-Sheet joining. As the result of creep test, GMT-Sheet is easily damaged in high temperature range, because it is sensitive to the temperature

• 한국기계가공학회지
• /
• 제16권6호
• /
• pp.133-138
• /
• 2017

Recently, CFRP composites are widely used as lightweight materials have with excellent mechanical properties and can beare widely used in various fields. In general, thermosetting resins are used for CFRP. However, in recent years, studies have been carried out using thermoplastic resins have been actively carried out to overcome the disadvantages of thermosetting resins. The LFT-D system is a molding method in which a fiber is directly cut to a the desired length while being impregnated with a thermoplastic resin to produce a compound and that is then press-molding molded to form the product. In this paper, before the production of the trailing arm, the compression molding analysis was carried out in order to grasp the problems that may occur during production. Through cCompression molding analysis was applied to calculate of the minimum press pressure and to compare and analysis analyze the molding conditions characteristic required to formfor forming the trailing arm.

• Advanced Composite Materials
• /
• 제16권4호
• /
• pp.361-376
• /
• 2007

Disposing of conventional fiber-reinforced polymers (FRPs) poses an environmentally challenging problem. Disposal of FRPs by combustion discharges carbon dioxide in the air because the resin of FRPs is made of fossil fuel. When they are disposed of in the ground, FRPs remain semipermanently without decomposing. In response to these problems, green composites are now being developed and are extensively studied as a material that produces a lower environmental burden. In this paper, green composites using kenaf fiber yarn bundles and PLA (poly(lactic acid)) are fabricated and their tensile properties are evaluated in the experiment. The tensile Young's modulus of all of the laminations is larger than that of PLA alone and the tensile strength of some laminations is larger than that of PLA alone. In particular, the value of UD composite of $0^{\circ$ shows double the tensile strength of PLA alone. Furthermore, the molding conditions for fabricating with a hot press are investigated and the heat resistant tensile properties of green composites are also reported.

• Design & Manufacturing
• /
• 제11권3호
• /
• pp.25-28
• /
• 2017

The production of carbon fiber reinforced thermoplastics(CFRTP) parts using an injection/compression molding process that differs from the conventionally used fabrication methods was investigated Before the application of composite molding in the injection/compression molding process, a simple compression molding experiment was performed using a hydraulic press machine to determine the characteristics of resin impregnation and to obtain a basic physical property data for the CFRTP. Based on these results, injection/compression molded specimens were manufactured and an additional insert/over molding process was applied to improve the impregnation rate of the molded specimens. The results demonstrated that the tensile strength of the molded parts using the faster injection/compression process was similar to that of a hydraulic press molded product.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2008년도 추계학술대회A
• /
• pp.996-999
• /
• 2008

Aspheric polymer lens fabrication using isothermal compression molding is presented in this paper. Due to increasing definition of an image sensor, higher precision is required by a lens which can be used as a part of an imageforming optical module. Injection molding is a factory standard method for a polymer optical lens. But achievable precision using injection molding has a formidable limitation due to the machining of complex mold structure and melting and cooling down a polymer melt under high pressure condition during forming process. To overcome the precision requirement and limitation using injection molding method, isothermal compression molding is applied to fabrication of a polymer optical lens. The fabrication condition is determined by numerical simulations of temperature distribution and given material properties. Under the found condition, the lens having a high precision can successfully be reproduced and does not show birefringence which results often in optical degradation.

• 한국기계가공학회지
• /
• 제20권6호
• /
• pp.76-81
• /
• 2021

A plastic noise barrier is a structure installed to minimize noise, and it is composed of the main plate, sound-absorbing plate, and sound-absorbing material. Plastic noise barrier structures have several advantages compared to other products, such as light weight, anticorrosion, durability, easy assembly, rapid construction, and low costs. In this study, the main and sound-absorbing plates were manufactured through extrusion molding, and the sound-absorbing plate was finished with a press to improve the conventional injection molding. Extrusion molding dies and punch dies were designed, and a profile extrusion-molding system was developed. Thus, inexpensive and efficient sound-absorbing and main plates can be produced, and the noise barrier structure can be assembled rapidly. Additionally, a noise barrier structure with extended service life and excellent quality can be constructed by creating uniform free space to accommodate increased temperatures after assembly and installation.

• 한국기계가공학회지
• /
• 제16권4호
• /
• pp.30-37
• /
• 2017

Weight reduction of the wheel is exerts a great influence on the running performance of the vehicle, a lot of research for a lightweight aluminum wheels progress. In order to select the molding conditions through the experiment on the carbon fiber prepreg molding process based on the design of the mold for manufacturing the carbon wheel using the carbon fiber pressure forming method, the carbon wheel molding process using the Taguchi method And to produce prototypes based on the results.

• 대한기계학회논문집
• /
• 제18권11호
• /
• pp.3084-3090
• /
• 1994

A new flow model is developed for the analysis of compression molding of sheet molding compounds(SMC) and penalty finite element formulation is presented to predict flow front progressions more accurately. In this model SMC is assumed nonisothermal fluid, which has different viscosities in extension and in shear. The flow is allowed to slip at the mold and is resisted by friction force which is proportional to the relative velocity at mold surface. For the verification of the model, the press force and flow patterns are compared with those of experiments and available results by other works in this field. It is also demonstrated, using the computational procedure described and the proposed model, that optimal initial charge shapes for the filling can be effectively computed.