• Transactions of the Korean Society of Mechanical Engineers
• /
• v.9 no.2
• /
• pp.181-189
• /
• 1985

The effect of the Coriolis force on the 2-D turbulent boundary layer which is developed in the side wall of the rotating rectangular flow channel was investigated. In this study, we measured mean velocities, turbulent velocity components(axial as well as lateral ones) and Reynolds stresses of the turbulent boundary layer. For high Reynolds number flows, the turbulent boundary layer without pressure gradient is hardly affected by the rotation. For low Reynolds number flows, however, the shearing stress at suction side decreases. Consequently, the velocity near the wall become slower so that the thickness of the viscous sublayer expands. On the other hand, the velocity near the wall at pressure side turns out increased.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.21 no.12
• /
• pp.2047-2054
• /
• 1997

This paper describes a measuring method of vibration mode shapes by the Electronic Shearography. This method called the speckle interferometer has many merits in practical use, such as low sensitivity to environmental noise, low limit of coherent-length and simple optical configuration. In this study, we developed Michelson-type shearing interferometer provided with a phase stepping mirror and with a bias modulation mirror to quantify the vibration gradient fields. Results of application to a simple cantilever plate show that the vibration amplitude fields obtained are in good agreement with those of the electronic speckle pattern interferometry (ESPI).

• Steel and Composite Structures
• /
• v.6 no.4
• /
• pp.319-333
• /
• 2006

A rectangular plate made of a porous material is the subject of the work. Its mechanical properties vary continuously on the thickness of a plate. A mathematical model of this plate, which bases on nonlinear displacement functions taking into account shearing deformations, is presented. The assumed displacement field, linear geometrical and physical relationships permit to describe the total potential energy of a plate. Using the principle of stationarity of the total potential energy the set of five equilibrium equations for transversely and in-plane loaded plates is obtained. The derived equations are used for solving a problem of a bending simply supported plate loaded with transverse pressure. Moreover, the critical load of a bi-axially in-plane compressed plate is found. In both cases influence of parameters on obtained solutions such as a porosity coefficient or thickness ratio is analysed. In order to compare analytical results a finite element model of a porous plate is built using system ANSYS. Obtained numerical results are in agreement with analytical ones.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.12 no.6
• /
• pp.1358-1371
• /
• 1988

The combustion process is the most important process in the S.I. engine since it determines performance and emissions. As the flame propagates slowly due to EGR or lean mixture, the fast burn system is widely used in the modern engines in order to improve engine performance. As the basic research for the fast burn system of the S.I engine, this study is aimed to identify the effects of the intake port design on the air motion inside a cylinder. In this study various intake ports were designed and tested. Swirl levels for the different intake ports were measured by a swirl meter and LDv.Also transient air motion inside a cylinder is further investigated following the motion of the boston. Out of the various intake ports tested in this study the masked shroud head (MSH) generates the highest swirl while keeping satisfactory volumetric efficiency. The MSH port also produces high level of turbulence by shearing action between cylinder wall and swirl.

• Geomechanics and Engineering
• /
• v.11 no.1
• /
• pp.95-116
• /
• 2016

A novel higher order shear-deformable beam model, which provides linear variation of transversal normal strain and quadratic variation of shearing strain, is proposed to describe the beam resting on foundation. Then, the traditional two-parameter Pasternak foundation model is modified to capture the effects of the axial deformation of beam. The Masing's friction law is incorporated to deal with nonlinear interaction between the foundation and the beam bottom, and the nonlinear properties of the beam material are also considered. To solve the mathematical problem, a displacement-based finite element is formulated, and the reliability of the proposed model is verified. Finally, numerical examples are presented to study the effects of the interfacial friction between the beam and foundation, and the mechanical behavior due to the tensionless characteristics of the foundation is also examined. Numerical results indicate that the effects of tensionless characteristics of foundation and the interfacial friction have significant influences on the mechanical behavior of the beam-foundation system.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.20 no.3
• /
• pp.16-23
• /
• 2021

The fracture characteristic of the bonded interface under the application of a sliding load to a double cantilevered specimen manufactured using lightweight material was examined. Inhomogeneously bonded materials such as Al6061-T6, CFRP, and CFRP-Al were employed. In the experiment, the specimen was loaded on both directions by applying a shearing load to the bonding interface. The experimentally obtained stress, specific strength and energy release rate values were examined. CFRP exhibited excellent specific strength. The experimental results demonstrated that the inhomogeneous bonded material CFRP-Al exhibited an overall high performance in comparison with the single materials.

• The International Journal of Costume Culture
• /
• v.8 no.1
• /
• pp.23-31
• /
• 2005

Mechanical properties and hand evaluation of wool/acrylic(W/A) blend knits were conducted before and after repeated washing to get the optimum W/A blending ratio, which could help achieve the optimum mechanical and hand properties of the knits. The five test fabrics using the yarns with different W/A blending ratios($\%$), 100/0, 70/30, 50/50, 30/70, 0/100, were knitted. The fabrics were washed by a rotating drum type washing machine. Then, objective mechanical and hand properties were evaluated by KES-FB, Kawabata evalution system for fabric. The results are as follows: there was no change in the hand value of the knitted fabric with the W/A-blended yarn caused by the change in the blending ratio before washing. After washing, however, the increase of acrylic's blending rate caused the bending property to decrease proportionally, while the friction coefficient of the surface property increased. Furthermore, the study showed that W/A 50/50 possesses the most superior tensile property and shearing property, which could attain the optimum blending ratio. Similar results in hand value were derived in all the samples. After washing, however, the increase in acrylic's blending rate caused a proportional decrease in KOSHI and an increase in FUKURAMI. In addition, W/A 50/50 gained the biggest NUMERI value, again corresponding to the optimum blending ratio. Similar results in total hand value were derived in all the samples before washing. After washing, though, all the total hand values decreased, and, as the wool fabric's blending rate increased, the total hand values proportionally decreased further.

• Journal of the Korean Society of Clothing and Textiles
• /
• v.31 no.2 s.161
• /
• pp.197-205
• /
• 2007

We investigated the effects of washing on the mechanical properties and hand values of spandex/cotton and cotton single jersey fabrics. These knitted fabrics were subjected to 30 laundering cycles with a drum-type washer and were followed by drying at $65^{\circ}C$ with a tumble dryer. The mechanical properties of the cotton knitted fabrics changed greatly during the first washing and then suffered no further change in their properties as the number of washing cycle increased. However, the properties of the spandex/cotton knitted fabrics changed continuously throughout all the washing cycles. The cotton/spandex knitted fabrics showed higher values in tensile and bending properties than did the cotton knitted fabrics, though both kinds of fabrics showed less difference in shearing, surface and compression properties. The spandex/cotton knitted fabrics which had proper density had a higher THV for winter underwear after 30 repeated washings than did the cotton knitted fabrics, and the THVs of both fabrics decreased with the increase in the number of washing cycles.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.22 no.3
• /
• pp.595-602
• /
• 1998

Specimens of 304 stainless steel were tested to failure at elevated temperatures under multiaxial stress states, uniaxial tension using smooth bar specimens, biaxial shearing using double shear bar specimens, and triaxial tension using notched bar specimens. Rupture times are compared for uniaxial, biaxial, and triaxial stress states with respect to the maximum principal stress, the von Mises effective stress, and the principal facet stress. The results indicate that the principal facet stress gives the best correlation for the material investigated, and this parameter can predict creep life data under multiaxial stress states with rupture data obtained with specimens under uniaxial stresses. The results also suggest that grain boundary cavitation, coupled with localized deformation processes such as grain boudary sliding, controls the lifetimes of the specimens.

• Journal of the Korean Society for Precision Engineering
• /
• v.19 no.6
• /
• pp.128-135
• /
• 2002

Burr is a projected part of finished workpiece. It is unavoidable and undesirable by-product of most metal cutting or shearing process. Also, it must be removed to improve the fit of machined parts, safety of workers, and the effectiveness of finishing operation. But deburring process Is one of manufacturing processes that have not been successfully automated, so deburring automation is strongly needed. This paper focused on developing a basic algorithm to find edge of workpiece and match two different image data for deburring automation which includes automatic recognition of parts, generation of deburring tool paths and edge/comer finding ability by analyzing the DXF drawing file which contains information of part geometry. As an algorithm fur corner finding, SUSAN method was chosen. It makes good performance in finding edge and corner in suitable time. And this paper suggested a simple algorithm to find matching point between CCD image and drawing file.