• Transactions of the Korean Society of Mechanical Engineers
• /
• v.18 no.6
• /
• pp.1430-1438
• /
• 1994

Friction-factors for honeycomb surfaces are measured with a flat plate tester. The flat plate test apparatus is described and method is discussed for determining the friction-factor experimentally. The friction-factor is calculated for the flat plate test based on the Fanno-line flow. The test parameters are honeycomb cell width, depth, clearance, inlet pressure, and Reynolds number(or Mach number). A new empirical friction-factor model for honeycomb surfaces are developed as a function of these parameters.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.10 no.1
• /
• pp.56-61
• /
• 1986

Rotor dynamic response of pumps is greatly influenced by the nature of the hydraulic forces arising from wearing seal, balance drum and impeller, etc.. Therefore, rotor dynamic analysis should be conducted during the design stage in order to aleviate some of the vibrational problems which might occur during the operational life of pumps. Previsousely, the authors have proposed the method to obtain the dynamic seal coefficients of the annular plain seal, convergent and divergent tapered seals, parallel grooved seal, spiral grooved seal and annular stepped seal. On the basis of these results, this paper presents the investigated effect of seals on the stability behavior of a centrifugal pump. The results show the effects of seal geometry, pressure difference, clearance, length/diameter ratio, on stability behavior.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2000.06a
• /
• pp.461-467
• /
• 2000

Mechanical problems are basically three dimensional nonlinear dynamic problems, which makes it difficult to solve. The difficulties are tried to overcome by modeling, i.e., simplifications of the system with the assumptions or negligence of minute effects. However, the correctness or usefulness of the model should be verified through the comparison with experimental results, which is the process of physical understanding of the system. The understanding of physics of the system make it possible to design or operation of the system. The effects of clearance and friction are always difficult problems in mechanical system due to its nonlinearity. The nonlinearity comes from piecewise-linear characteristics of the stiffness and damping of the system. The modeling of piecewise-linearity and the experimental result are discussed in this paper for impact and friction oscillator and rotor rubbing problem, which is the combination of impact and friction problems.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.28 no.8 s.227
• /
• pp.1166-1173
• /
• 2004

In this paper, in order to apply magnetic fluid with superparamagnetic property as the substitute of ferromagnetic materials, physical properties of magnetic fluid are investigated. A targeted drug delivery system using a capsule filled magnetic fluid is proposed where a magnetic fluid capsule and cylinders are considered as a drug and vital organs, respectively. The dynamic governing equation of this system first is derived. Fluid viscosity, clearance between a cylinder and a magnetic fluid capsule, and levitation height with respect to different cylinder height are considered as major parameters to evaluate dynamic characteristics of the system. The experiments and simulations for the position control of the magnetic fluid capsule in various cylinders are conducted using PID controller. The results show that magnetic fluid with the superparamagnetic property can be applied to a targeted drug delivery system.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.29 no.7 s.238
• /
• pp.955-963
• /
• 2005

This research investigates dynamic characteristics of a linear motion (LM) guide through a experimental result and theoretical analysis. The stiffness in the LM guide is determined by the preloading due to the minus clearance between the ball bearing and the contact surface and it can be derived by Hertzian contact theory and the nonlinear motion of equation. The vibration analysis is performed using Lagrange equations and its result agrees with the experiment result. Using the sensitivity analysis on design parameters such as the contact angles of ball bearings and the eccentricity of mass center, the variation of the natural frequencies can be predicted.

• Journal of Advanced Marine Engineering and Technology
• /
• v.27 no.3
• /
• pp.421-428
• /
• 2003

The aerodynamic characteristics of the Wells turbine for wave energy conversion have been investigated by the numerical simulation to reproduce hysteretic behaviors. The pressure distributions on the suction surface of the blade were investigated to find out the cause of the hysteretic mechanism. The results have shown that the hysteretic behavior is associated with streamwise vertical flow appearing near the suction surface and become more obvious. as the tip clearance and solidity change. Also it has shown that such phenomena occur due to different behaviors of wakes in the accelerating and decelerating flow process. The CFD analysis shows a good agreement with experimental results.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.30 no.9 s.252
• /
• pp.913-920
• /
• 2006

Three-dimensional flow and aerodynamic loss in the tip-leakage flow region of a high-turning first-stage turbine rotor blade with a squealer tip have been measured with a straight miniature five-hole probe for the tip gap-to-chord ratio, h/c, of 2.0%. This squealer tip has a indent-to-chord ratio, $h/{st}/c$, of 5.5%. The results are compared with those for a plane tip $(h_{st}/c=0.0%)$. The squealer tip tends to reduce the mass flow through the tip gap and to suppress the development of the tip-leakage vortex. Therefore, it delivers lower aerodynamic loss in the near-tip region than the plane tip does. At the mid-span, however, the aerodynamic loss has nearly the same value for the two different tips.

• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 2003.11a
• /
• pp.273-280
• /
• 2003

The purpose of the paper is to investigate the noise characteristics of cylindrical roller bearings under radial load. The effects of radial clearance of the bearing, viscosity of the lubricant and number of the roller on the noise of the bearing are also examined. The results and discussions of the present paper might aid in the low-noise design of the cylindrical roller bearing.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.17 no.12
• /
• pp.3045-3054
• /
• 1993

The mechanics related with piston-slap induced vibration has been studied in terms of non-dimensionalized dynamic equation of motion, various non-dimensional parameters such as non-dimensional side-thrust force and non-dimensional impact velocity throughout the numerical simulation. Experimental verification on the suggested prediction method has been also performed by using single cylinder engine which was carefully designed and manufactured to wisely control the engine parameters, especially clearance and the mass of piston. The predicted and experimentally observed vibration signature confirm that the proposed method is practically useful.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.24 no.7
• /
• pp.916-923
• /
• 2000

Numerical study of three-dimensional turbulent flow in a forward curved centrifugal fan is presented. Standard $k-{\varepsilon}$ turbulence model and non-orthogonal curvilinear coordinates arc used to consider the turbulent flow field and complex geometry. Finite Volume approach is adopted for discretization scheme and structured grid system is used to help convergence. Multiblock grid system is used for flow field and divided into five domains that are inlet, outlet, impeller, tip clearance and scroll. It is assumed that the flow field is steady and incompressible. These numerical results are compared with the experimental data inside a rotor and at the fan outlet. Most important flow features are captured through this numerical approach. Finally details of flow field inside a fan are described and analyzed.