• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.13 no.7
• /
• pp.633-640
• /
• 2002

In this paper, the small chip meander antenna for dual-frequency operation is presented. The proposed chip meander antennas was fabricated by the ceramic chip using LTCC-MLC process. It is a novel compact dual-frequency design using a meandered patch that achieves more degrees of freedom for adjusting dual-frequency operation and the size reduction with narrow frequency ratio. And it is proposed that the 3D structure for additional size reduction of the meander antenna. The size reduction of the 3D meander antenna is as large as 50 % as compared to the design for dual-frequency operation not using 3D structure. It is observed that the principle of dual-frequency operation through current distribution, return loss and radiation pattern.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.22 no.8
• /
• pp.641-644
• /
• 2009

We have studied on the microwave characteristics for the meander type inductors on the MgO substrates and $Al_2O_3$ substrates by employing 3-D high frequency simulation, respectively. Proper designs of meander type inductors were proposed and confirmed through the high frequency simulations, 5, 7, 9, 11, and 13 turns meander type inductors have been choose to analyze the electrical properties for the microwave passive component applications. The Al top electrodes have 282 nm length, 45 nm width, 100 nm thickness and 15 nm gap. The simulations were carried out from 50 MHz to 30 GHz, Frequency dependent inductances and quality factor were calculated by employing the equivalent circuit model of meander type inductors. The self resonances frequency of meander type inductor were shifted from high frequency to low frequency range as the number of the turn of inductors was increased. From the microwave simulations, the inductances and quality factors of meander type inductors were extracted through the scattering parameter.

• Progress in Superconductivity
• /
• v.5 no.2
• /
• pp.118-123
• /
• 2004

We investigated quench distribution in AU/YBCO thin film meander lines with a heater. Quench distribution during faults is important for superconducting fault current limter applications, because uniform quench allows application of higher voltages across the meander lines. AU/YBCO thin films grown on sapphire substrates were patterned into meander lines by photolithography. Gold films grown on the rear sides of the substrates were also patterned into meander lines, and used as heaters. Meander lines on the front and the rear sides were connected in parallel. The meander lines were subjected to simulated AC fault currents for quench measurements during faults. They were immersed in liquid nitrogen during the experiment for effective cooling. Resistance of the AU/YBCO meander lines initially increased more rapidly with the rear heater than without, and consequently the fault current was limited more. The resistance subsequently became similar, The resistance distribution was more uniform with the heater, especially during the initial quench. Quench was completed more uniformly and significantly earlier. This resulted in uniform distribution of dissipated power. These results could be explained with the concept of quench propagation, which was accelerated by heat transfer across the substrate from the rear heater.

• Proceedings of the Korea Electromagnetic Engineering Society Conference
• /
• 2005.11a
• /
• pp.225-230
• /
• 2005

The proposed Triple-band Compact Chip Antenna using Coupled Meander line and stacked meander Structure for Mobile RFID/PCS/WiBro. The proposed antenna is designed to operate at 900, 1800, and 2350 MHz, and is realized by parasitic coupled and stacked a meander line. Meander lines are using extend length of effective current path more than monopole and contribute miniaturization. The coupled meander line controls the excitations of the Mobile RFID and PCS, stacked meander line controls the excitation of the WiBro. The proposed antenna size is $11mm\times22.5mm\times1mm$. The antenna supports 900MHz, 1800MHz and 2350MHz operations simultaneously with bandwidths of 33MHz, 230MHz and 100MHz, respectively. The proposed antenna gains are result of simulation to be -0.8dBi, 3dBi and 3.8dBi, respectively.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2008.06a
• /
• pp.352-352
• /
• 2008

폐 자기회로 구조를 갖는 Meander 형태의 Inductor 설계를 위해 HFSS 프로그램을 이용하여 Meander Inductor를 시뮬레이션 하였다. Meander Inductor의 turn 수(N) 및 폭(W), 두께(T), 랩(G)의 변화에 따른 인덕턴스(L), S-parameter(S)와 Q-factor(Q)의 변화를 HFSS 를 통해 측정하였다. Al2O3 기판과 MgO의 두께는 각각 680um, 50um로 고정하였고, silver electrode를 이용하여 Meander 타입의 Inductor를 설계하였다. Meander Inductor의 turn수(6,7,8turn)의 변화를 측정한 결과, 8턴이었을 때 Q-factor가 19로서 가장 높은 결과를 얻었다. L의 결과 값은 공진 주파수와 의 관계에 의해 6turn일 때 L값은 17GHz에서 공진현상이 나타났다. 또한 W, G, T에 변화를 주어 설계한 뒤 시뮬레이션의 결과 값을 측정하였다. 그 값을 서로 비교한 결과, 변수들의 변화에 따라 L값과 Q-factor가 변화되었다. 이 논문에서는 각 변수에 따른 meander inductor의 특성을 HFSS 시뮬레이션을 통해 비교하고자 한다.

• Journal of Advanced Marine Engineering and Technology
• /
• v.34 no.2
• /
• pp.325-331
• /
• 2010

In this study, highly miniaturized short-wavelength meander line employing eriodically patterned ground structure (PPGS) was developed for application to miniaturized on-chip passive component on GaAs MMIC (monolithic microwave integrated circuit). The meander line employing PPGS showed shorter wavelength and slow-wave characteristic compared with conventional meander line. The wavelength of the meander line employing PPGS structure was 17 % of the conventional meander line on GaAs MMIC. Due to its slow-wave structure, the meander line employing PPGS exhibited large propagation constant than conventional meander line, which resulted in larger phase shift and shunt inductance value. Above results indicate that the meander line employing PPGS is a promising candidate for application to a development of miniaturized on-chip RF components as well as inductor with a high inductance value on GaAs MMIC.

• Water for future
• /
• v.14 no.1
• /
• pp.39-49
• /
• 1981

The purpose of this study is to examine the meander charactericstics for the rivers in Korea..In this study, the new characteristics factors of meander are proposed, and the relationships among the factors proposed in this study and the existing factors are derived. An attempt is made to find considerable relation among meander characteristics, but width and meander belt did not show any defined trend and considerable scatter of points was observed. Relationships among the meander length, belt and flowrate, etc., which are factors of meander characteristics, are analyzed the 67 rivers above 30km in length. Channel shape factor which is the ratio of the length from the starting point to the end to the channel lenght, tortuosity which is the ratio of the curved channel length against the channel length are suggested for a new characteristics factor of meander. They are well correlated with channel length, Horton's shape facotr and meander gradient, consequently have to be important measures of river meander. The result of the detailed comparison and the analysis of degree of sinuosity, velocity and water surface slop are brought light on the fact show that the curved reach is morestable than the straight one. The ratio of the meander length to the meander belt and its accumulative frequency showed excellent correlationship when plotted on the semi-log paper. The results of regression analysis of meander belt and meander length show linear for the South Han river branches and power curve for the Geum river and the Nakdong river branches.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.11 no.5
• /
• pp.738-747
• /
• 2000

In this paper it is shown that the meander line at the low frequency can be thought as the single transmission line whose characteristic impedance is approximately equal to that without coupling. But the length is contracted from that without coupling. The approximate contraction ratio is derived for weak coupling and is compared with the circuit simulation results and the EM simulation results. The formula are in good agreement with the simulation results in weak coupling.

• Journal of the Korean Institute of Telematics and Electronics
• /
• v.7 no.2
• /
• pp.13-20
• /
• 1970

The dispersion characteristics of tape meander line were analyzed by electromagnetic field theory. The several different tape meander lines were photoetched on copper printed-bakelit substrate, and these tape meander line structures were inserted into the X-band waveguide. Phase bridge method was used for the dispersion characteristics measurement of meanderline. The measured. results were plotted on diagram(Brillouin diagram) and compared with theoretical values. Measured results were consistent with theoretical Values. But, on the measured diagram, passband midfrequency was lower than theoretical value. It was believed that the discrepancy was due to the backelite loading. The group velocity of stagger tuned meander line was higher than that of uniform meander live, and the freqnency band of constant group velocity of stagger tuned meanderline was sider than that of uniform meander line.

• The Journal of the Acoustical Society of Korea
• /
• v.10 no.5
• /
• pp.5-10
• /
• 1991

본 연구에서는 알루미늄 금속의 결합 검출을 위한 meander line 형 EMAT를 모의 실험을 통해 설계하고 그 대역특성을 연구분석 하였다.