• 한국전산유체공학회지
• /
• 제17권3호
• /
• pp.1-10
• /
• 2012

Large Eddy Simulation(LES) of turbulent mass transfer in fully developed turbulent pipe flow has been performed to study the effect of Reynolds number on the concentration fields at $Re_{\tau}=180$, 395, 590 based on friction velocity and pipe radius. Dynamic subgrid-scale models for the turbulent subgrid-scale stresses and mass fluxes were employed to close the governing equations. Fully developed turbulent pipe flows with constant mass flux imposed at the wall are studied for Sc=0.71. The mean concentration profiles and turbulent intensities obtained from the present LES are in good agreement with the previous numerical and experimental results currently available. To show the effects of Reynolds number on the turbulent mass transfer, the mean concentration profile, root-mean-square of concentration fluctuations, turbulent mass fluxes, cross-correlation coefficient, turbulent diffusivity and turbulent Schmidt number are presented.

• 대한기계학회논문집B
• /
• 제21권6호
• /
• pp.725-734
• /
• 1997

The effect of helical intake port geometry on in-cylinder swirl flow characteristics was studied. Two helical intake ports were selected to change swirl ratio, mean flow coefficient with the variation of valve lifts, valve eccentricity ratios and axial distance. The measurements were made by using an impulse swirl meter. The port B modified to increase the swirl ratio( $R_{s}$) had the tendency of the increased non-dimensional rig swirl ( $N_{r}$) distribution in comparison with that of the port A. And the $N_{r}$ distribution was remarkably improved at low valve lifts. The modification of the geometry to increase the swirl ratio ( $R_{s}$) in helical intake port resulted in the decrease of the mean flow coefficient ( $C_{f(mean)}$) regardless of valve eccentricity ratio ( $N_{y}$). And also non-dimensional rig swirl ( $N_{r}$) in the high valve lift affected the calculation of swirl ratio considerably.onsiderably.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2001년도 춘계학술대회논문집D
• /
• pp.201-207
• /
• 2001

We modeled the liquid film dryout(LFD) process for both tube and annulus which have uniformly heated vertical channels. We set phenomenological initial conditions in the model. The initial void fraction on the onset of the annular flow location is derived from the physical chum-to-annular flow criterion with the help of the drift-flux-model. The initial thermodynamic-equilibrium-quality is calculated by iteration with the flow quality to find the onset of the annular-flow location. Present model tends to predict very well at the lower exit quality but under-estimates at the higher exit quality. We found that the prediction error of the present model is gradually bigger as the inlet subcooling approaches near the saturation. We obtained excellent results for both tube and annulus channels as the mean of 0.97 and root-mean-square error of 11% for the number of 3883 experimental data on tubes, and of 0.96 and of 12% for 593 on annuli. The present model extended the applicable range to the relatively low exit quality region than previous LFD models.

• 대한기계학회논문집
• /
• 제18권9호
• /
• pp.2423-2430
• /
• 1994

Several factors of the efficient combustion process are shape of combustion chamber, position of spark plug, turbulence flow and so on. the shape of combustion chamber and position of spark plug are constrained to geometrically, and then it could not make a change the shape easily. But the turlence flow in combustion chamber have a great influence on combustion phenomena, and which is much easier to control relatively. And since characteristics of turbulence flow would be very important to the stability of combustion and performances, This study is also essential to future engine-low emission and lean burn engine. This paper shows that the visualization of the turbulence flow of single cylinder engine by using 2way, $45^{\circ}$ inclined and 2 channel hot wire probe through the park plug hole. We also study the characteristics of turbulence flow by means of ensemble averaged mean velocity, turvulence intensity and integral length scale.

• 유체기계공업학회:학술대회논문집
• /
• 유체기계공업학회 2004년도 유체기계 연구개발 발표회 논문집
• /
• pp.315-320
• /
• 2004

Swing check valves are the most common type of check valve in nuclear power plant and need to be operated property to perform their functions and to keep the valve internals stable. However, for a swing check valve disc to remain stable, the opening characteristics should be identified and the upstream flow velocity should be enough to hold the disc fully open and without motion. Thus it is necessary to develop a model for predicting the flow velocity for a given disc opening. In the present study, the disc positions with mean flow velocity were measured for 3 inch and 6 inch swing check valves. Comparison of the measurements with the existing models showed that the models underestimate the mean flow velocity for a given disc position. Therefore, the existing model for predicting swing check valve disc position was improved with the realistic disc impingement area perpendicular to the flow stream and the experimental data. The result showed that the improved model with the best estimate of kb = 0.04 predicts well the disc openings of 6 inch swing check valve, especially in the low velocity region. For better prediction of the disc opening at high flow velocity, however, it is recommended to develop a kb correlation with the disc angle.

• 대한기계학회논문집B
• /
• 제24권1호
• /
• pp.75-84
• /
• 2000

Performance and flow characteristics of a small forward swept propeller fan for home refrigerators are studied experimentally. An unusual discontinuity is observed in the performance curve of the fan. Mean flow fields measured with as-hole Pitot probe reveal that the flow is axial at the high flow rate and radial at the low flow rate. The flow structure changes abruptly across the discontinuity. Unsteady flow measurements with a set of hot-wire probes indicate that near the discontinuity a single-cell stall rotates at 40% speed of the fan speed, while away from the discontinuity the flow shows periodic variation corresponding to the blade passage frequency. Phase-lock averaged flow fields measured with a triple-sensor hot-wire probe show that there appears radially inward flow over the pressure side of the blade and the outward passage flow over the tip.

• 한국농공학회지
• /
• 제42권3호
• /
• pp.45-55
• /
• 2000

This study was carried out to derive optimal design low flows bythe Weibull-3 and Wakeby distributions for the partial consecutive duration series at seven watersheds along Han. nagdong, Geum Yeongsan and Seomjin river systems. L-coefficient of variation L-skewness and L-kurtosis were calculated by the L-moment ratio respectively. Parameters were estimated by the method of L-Moments with consecutive duration. Design low flows obtained by method of L-Moments using with consecutive duration, Design low flows obtained by method of L-Moments using different methods for plotting positions formulas in the Weibull-3 and Wakeby distributions were compared by the Root Mean Square Errors(RMSE). It has shown that design low flows derived by the method of L-moments using Weivull plotting position formula in Wakeby distribution were much closer to those of the observed data in comparison with those obtained by the methods of L-moments with the different formulas for plotting positions in Weibull-3 distribution from the viewpoint of Root Mean Square Errors.

• 한국수자원학회논문집
• /
• 제43권9호
• /
• pp.823-833
• /
• 2010

침수식생 개수로 흐름은 식생영역과 상부영역에 서로 다른 흐름구조를 보인다. 즉, 식생영역에서 전단으로 인해 생성되는 난류는 억제되며 비교적 균일한 유속 분포를 보이며 상부영역에서는 일반 개수로 흐름과 유사한 흐름구조를 보인다. 이와 같이 두 상이한흐름구조가 결합된 복잡한 흐름특성으로 인해 침수식생 개수로흐름은 공학적인 관심의 대상이 되어왔다. 본 연구에서는 침수식생 개수로 흐름의 층적분 모형의 비교 분석을 수행하였다. 일반적으로 식생흐름의 층적분 모형은 층의 수에 따라 2층 및 3층모형으로 구분한다. 즉, 전체 수심을 식생영역과 상부영역으로 구분하는 2층모형과 식생영역을 바닥 조도의 영향 유무에 따라 내부 및 외부 식생영역으로 구분하는 3층모형으로 분류된다. 본 연구에서는 2층모형과 3층모형을 비교하였다. 다양한 실험조건에 적용한 결과, 3층모형이 식생영역에서 유속의 변화를 고려할 수 있으나 결과는 레이놀즈응력 분포에 민감하며, 적분된 유속은 2층모형에 의한 예측 결과가 더욱 정확한 것으로 나타났다. 3층모형에서 내부 식생영역의 결과가 전체 흐름구조에 미치는 영향이 무시할 수 있으므로 이 점을 착안하여 식생영역에서 유속 변화가 고려되는 수정 2층모형을 제시하였다. 수정 2층모형에서 가정하는 레이놀즈응력 분포는 상부영역에서는 선형, 식생영역에서는 멱함수 형으로 변화한다. 다양한 조건에 적용한 결과, 수정 2층모형이 대체로 기존의 모형과 비슷한 정도의 예측을 수행하나 식생밀도가 매우 작은 흐름의 경우 예측 결과가 불량한 것으로 나타났다.

• Journal of Korean Neurosurgical Society
• /
• 제52권6호
• /
• pp.534-540
• /
• 2012

Objective : Brainstem arteriovenous malformation (AVM) is rare and radiosurgical management is complicated by the sensitivity of the adjacent neurological structures. Complete obliteration of the nidus is not always possible. We describe over 20 years of radiosurgical procedures for brainstem AVMs, focusing on clinical outcomes and radiosurgical techniques. Methods : Between 1992 and 2011, the authors performed gamma knife radiosurgery (GKRS) in 464 cerebral AVMs. Twenty-nine of the 464 patients (6.3%) reviewed had brainstem AVMs. This series included sixteen males and thirteen females with a mean age of 30.7 years (range : 5-71 years). The symptoms that led to diagnoses were as follows : an altered mentality (5 patients, 17.3%), motor weakness (10 patients, 34.5%), cranial nerve symptoms (3 patients, 10.3%), headache (6 patients, 20.7%), dizziness (3 patients, 10.3%), and seizures (2 patients, 6.9%). Two patients had undergone a previous nidus resection, and three patients had undergone a previous embolization. Twenty-four patients underwent only GKRS. With respect to the nidus type and blood flow, the ratio of compact type to diffuse type and high flow to low flow were 17 : 12 and 16 : 13, respectively. In this series, 24 patients (82.8%) had a prior hemorrhage. The mean target volume was 1.7 $cm^3$ (range 0.1-11.3 $cm^3$). The mean maximal and marginal radiation doses were 38.5 Gy (range 28.6-43.6 Gy) and 23.4 Gy (range 18-27 Gy), and the mean isodose profile was 61.3% (range 50-70%). Results : Twenty-four patients had brainstem AVMs and were followed for more than 3 years. Obliteration of the AVMs was eventually documented in 17 patients (70.8%) over a mean follow-up period of 77.5 months (range 36-216 months). With respect to nidus type and blood flow, the obliteration rate of compact types (75%) was higher than that of diffuse types (66.7%), and the obliteration rate of low flow AVMs (76.9%) was higher than that of high flow AVMs (63.6%) (p<0.05). Two patients (6.9%) with three hemorrhagic events suffered a hemorrhage during the follow-up period. The annual bleeding rate of AVM after GKRS was 1.95% per year. No adverse radiation effects or delayed cystic formations were found. Conclusion : GKRS has an important clinical role in treatment of brainstem AVMs, which carry excessive surgical risks. Angiographic features and radiosurgical techniques using a lower maximal dose with higher isodose profiles are important for lesion obliteration and the avoidance of complications.

• 한국산학기술학회논문지
• /
• 제12권5호
• /
• pp.2261-2266
• /
• 2011

초음파 컬러 유동 사상에서 가장 많이 사용되는 Kasai 알고리듬은 래그-1 자기상관 방법으로서 적은 계산량으로 비교적 우수하게 도플러 평균주파수를 추정한다. 하지만 특히 깊은 곳을 영상화하는 경우 낮은 신호 대 잡음비로 인해 추정성능이 저하된다. 본 논문에서는 낮은 신호 대 잡음비에서도 Kasai 알고리듬보다 우수한 디에일리어스된 래그-2 자기상관방법을 제안하고 시뮬레이션을 통해 성능을 검증하였다. 제안한 방법은 잡음이 존재하는 경우 도플러 평균주파수 추정 성능을 평균 자승 오차 측면에서 전반적으로 약 2~3dB 정도 개선시켜줌을 확인하였다.