• KSBB Journal
• /
• 제13권6호
• /
• pp.730-734
• /
• 1998

An이ew식과 Aiba삭을 조합하여 에탄올 생산단주인 Saccharomyces cerevisiae ATCC 24858의 비성장속도를 당농도와 에탄올 농도의 함수로 표현하였다. 기침의 저해영향을 받지 않는 최대 당농도 $S_m$은 150 g/L이며 기질의 저해영향은 기질농도 S와 $S-S_{max}$항의 함수로 표현되었다. 최대 비성장 속도 ${\mu}max 는 0.49 hr^{-1}, Monod상수 K_s$는 19 g/L, Andrew식의 기질저해상수 $K_1$는 139 g/L이였다. 또한 비성장속도에 영향을 마치지 앓는 최대알콜농도 Pm이 존재하였으며 그 값은 2 g/L 이였다. 따라서 Aiba식에서 비성장속도에 영향을 미치는 에탄올 농도항은 P-Pm으보 표현되었다. 본 연구의 알코올생산균주에 대한 비성장속도의 완성된 수식은 디음과 같으며 이 수식에 위한 계산값은 평균오차 6% 내외의 범위에서 실험값과 일치하였다.

• 설비공학논문집
• /
• 제23권3호
• /
• pp.223-230
• /
• 2011

The power cycle using ammonia-water mixture as a working fluid is a possible way to improve efficiency of the system of low-temperature source. In this work thermodynamic performance of the ammonia-water regenerative Rankine cycle with partial-boiling flow is analyzed for purpose of extracting maximum power from the source. Effects of the system parameters such as mass fraction of ammonia, turbine inlet pressure or ratio of partial-boiling flow on the system are parametrically investigated. Results show that the power output increases with the mass fraction of ammonia but has a maximum value with respect to the turbine inlet pressure, and is able to reach 22 kW per unit mass flow rate of source air at $180^{\circ}C$.

• ETRI Journal
• /
• 제30권1호
• /
• pp.113-128
• /
• 2008

Turbo codes are extensively used in current communications standards and have a promising outlook for future generations. The advantages of software defined radio, especially dynamic reconfiguration, make it very attractive in this multi-standard scenario. However, the complex and power consuming implementation of the maximum a posteriori (MAP) algorithm, employed by turbo decoders, sets hurdles to this goal. This work introduces an ASIP architecture for the MAP algorithm, based on a dual-clustered VLIW processor. It displays the good performance of application specific designs along with the versatility of processors, which makes it compliant with leading edge standards. The machine deals with multi-operand instructions in an innovative way, the fetching and assertion of data is serialized and the addressing is automatized and transparent for the programmer. The performance-area trade-off of the proposed architecture achieves a throughput of 8 cycles per symbol with very low power dissipation.

• 한국가스학회지
• /
• 제16권1호
• /
• pp.8-14
• /
• 2012

수소는 온실가스 배출을 저감하기 위한 미래 에너지로 고려되고 있지만, 폭발위험에 대한 문제점을 지니고 있다. 따라서 수소가 미래 에너지로 사용되기 위해서는 폭발위험에 대한 연구가 충분히 이루어져야 한다. 폭발위험은 폭발충격에 대한 이해 즉, 폭발과정에서 압력 상승속도에 대한 분석과 밀접한 관계가 있다. 본 연구에서는 폭발에 영향을 미치는 변수, 즉 연소 전후의 비열비, 화학평형상태에서 최대폭발압력, 그리고 연소속도, 이들 변수가 압력 상승속도에 미치는 영향을 살펴보았다. 화학평형상태에서 최대폭발압력과 연소속도는 압력 상승곡선에 큰 영향을 미치는 것을 알 수 있었고, 미연소 가스의 비열비는 초기압력 상승속도보다 최종압력 상승속도에 더욱 영향을 미치고, 연소가스의 비열비는 반대로 초기압력 상승속도에 더욱 큰 영향을 미치는 것을 알 수 있었다. 연소속도는 실험 데이터로부터 구하였으며 밀폐공간에서 수소가스 폭발에서는 폭연에서 폭굉으로 전이가 일어나기에는 연소속도가 매우 느림을 알 수 있었다.

• Advances in Energy Research
• /
• 제8권3호
• /
• pp.185-202
• /
• 2022

This research work focuses to design and simulate a 200W solar power system with electrical power conservation scheme as well as thermal power conservation modeling to improve power extraction from solar power plant. Many researchers have been already designed and developed different methods to extract maximum power while there were very researches are available on improving solar power thermally and mechanically. Thermal parameters are also important while discussing about maximizing power extraction of any power plant. A specific type of coolant which have very high boiling point is proposed to be use at the bottom surface of solar panel to reduce the temperature of panel in summer. A comparison between different maximum power point tracking (MPPT) technique and proposed MPPT technique is performed. Using this proposed Thermo-electrical MPPT (TE-MPPT) with Deep Learning Algorithm model 40% power is conserved as compared to traditional solar power system models.

• Steel and Composite Structures
• /
• 제19권3호
• /
• pp.585-599
• /
• 2015

This paper presents the experimental work on fatigue life and specific fatigue strength of circular hollow sectioned steel tube and wood filled circular hollow section steel tube. Burning effect was observed in the case of circular hollow sectioned steel tube when it is subjected to Maximum bending moment of 19613.30 N-mm at 4200 rpm, but this did not happen in the case of wood filled hollow section. Statistical analysis was done based on the experimental data and relations have been built to predict the number of cycles for the applied stress or vice versa. The relations built in this paper can safely be applied for design of the fatigue life or fatigue strength of circular hollow sections and wood filled hollow sections. Results were validated by static specific bending strengths determined by ANSYS using a known applied load.

• 열처리공학회지
• /
• 제13권4호
• /
• pp.231-238
• /
• 2000

Flake graphite cast irons with the high damping capacity have been used for the control of vibration and noise occurring in the members of various mechanical structures under vibrating conditions. However, the damping capacity which is morphological characteristics of graphite is one of the important factors in reducing the vibration and noise, but hardly any work has deal with this problem. Therefore, the authors have examined the damping capacity of various cast irons with alloying elements and studied the influences of the matrix structures, mechanical properties and morphological characteristics of graphite. The main results obtained are as follows: Effects of pouring temperature on the damping capacities and mechanical properties were investigated in 3.6%C cast iron. At $1400^{\circ}C$, specific damping capacity showed the maximum value, and decreased with increase pouring temperature. Mechanical properties showed opposite trend with the damping capacity. And then, effects of Ni on the damping capacities and mechanical properties have been investigated in 3.6%C gray cast iron. At 0.2%Ni content, specific damping capacity showed the maximum value, and decreased with further increase in Ni content. Graphite length also showed same behavior. This indicates that the specific damping capacity has a close relation with graphite length. In case of Mo addition in 3.6%C-0.2%Ni cast iron, specific damping capacity and tensile strength was 27% and $20kgf/mm^2$ at 3.6%C-0.2%Ni-0.3%Mo cast iron respectively.

• Journal of the Korean Wood Science and Technology
• /
• 제12권2호
• /
• pp.10-19
• /
• 1984

The $3{\times}3{\times}30$ ($cm^3$) sized lumbers of Populus alba-grandulosa L. were treated with four fire-retardant solutions of ammonium sulfate, monoammonium phosphate, diammonium phosphate and aluminium chloride for 1, 15, 30, and 60 minutes and 1, 3, and 7 days. Thereafter they were air-dried and burned at high temperature about $1,800^{\circ}C$ and for short time of five minutes. This study estimated the relationship between absorbed chemical amounts and rate of weight loss or residual bending strength of these burned lumbers. The results were as follows: 1) In absorption amount of fire-retardant chemicals, diammonium phosphate showed the largest, aluminium chloride the smallest, but monoammonium phosphate and ammonium sulfate showed similar level. 2) The absorption amount of chemicals was decreased with the increase of specific gravity in the same species except aluminium chloride. 3) The rate of weight loss was decreased as the absorption amount of chemicals increased, especially monoammonium phosphate was most effective. 4) The MOR value of the residual bending strength was increased as the absorption amount of chemicals increased and especially monoammonium phosphate showed the most efficient effect. 5) Aluminium chloride showed more striking increase of MOR value of residual bending strength with the increase of absorption amount than any other chemical, therefore its MOR value was similar to the maximum MOR value of the most effective monoammonium phosphate. 6) The correlation between weight loss and MOR value of the residual bending strength was negative and aluminium chloride showed the most striking negative relation, but the others showed similar trends. 7) The correlation between work to proportional limit and absorption amount of chemicals was positive and the degree of increase in work to proportional limit was most in aluminium chloride, and the next, in monoammonium phosphate and diammonium phosphate in turn. 8) The correlation between work to maximum load and absorption amount of chemicals showed positive and diammonium phosphate revealed the best result and aluminium chloride showed better results than other two chemicals.

• 대한기계학회논문집
• /
• 제14권5호
• /
• pp.1356-1364
• /
• 1990

본 연구에서는 단열해석에 재생기효율을 고려함으로써 보다 합리적인 예비설 계조건을 도출하고자 함이다. 스터링기관용 재생기의 특성검토를 통하여 예비설계에 적합한 재생기효율을 정립하며, 기 발표된 단열모델에 대한 해석적 근사해에 적용하는 방법으로 접근한다. 재생기효율이 고려될 경우 기관의 기본형태와 연관된 위상각, 행정체적비, 불용체적비, 압축비등 설계인자의 최적조건에 관하여 취급하며 온도비, 비열비등 부여조건의 변화에 따른 영향을 검토한다.

• 한국안전학회지
• /
• 제27권4호
• /
• pp.96-100
• /
• 2012

Low back pain (LBP) is a major issue in modern industrialized society which is mainly caused by manual material handling (MMH) tasks. The objective of this study was to provide scientific data for establishing work standard for Korean workers throughout the laboratory experiment including some specific lifting tasks. Thirty male college students were recruited as participants. The maximum voluntary contraction (MVC), recommended weight limit (RWL), and psychophysical safety weight using Borg's CR-10 scale were studied. Results showed that the RWL was 8.4% MVC higher than the proposed psychophysical safety weight. Based on this result, it is suggested that the NIOSH lifting equation (NLE) should not be directly applied to Korean without reasonable modifications. The ratio of psychophysical safety weight to MVC was ranged from 20.1 to 26.4%. It is expected that use of the methodology in this study may provide better expectation of the work ability of Korean for reducing lower back pains caused by MMH.