• Transactions of the Korean Society of Mechanical Engineers
• /
• v.14 no.3
• /
• pp.694-701
• /
• 1990

The cycle of heat engine which produces the maximum power output is constructed when heat sources are finitely constant, and the maximum power as a thermodynamic limit of the engine, is obtained. The characteristics of the maximum power cycle are as follows, which represent the operation conditions and design conditions of the heat engine to produce the maximum power output. In heat exchangers, the temperature profiles of the heat source and the working fluid have the same functional formula and the ratio of the working fluid temperature to the heat source temperature is constant. When heat capacity flow rates(product of the specific heat and the mass flow rate) of the working fluid as well as the heat source are constant, the values of those of working fluid exist between those of two heat sources. The relation of the temperature and the heat capacity flow rate is established without the states of the heat sources and the capacities of heat exchangers, which is ( $T_{h}$/ $T_{H}$)( $C_{h}$/ $C_{H}$)=( $T_{1}$/ $T_{L}$)( $c_{1}$/ $c_{L}$)=1. The capacity of the heat exchanger of hot side is equal to that of cold side regardless of the states of the heat sources and the total capacities of heat exchangers.hangers.ers.

• 한국태양에너지학회:학술대회논문집
• /
• 2008.04a
• /
• pp.68-74
• /
• 2008

This paper describes the causes and effects that have influence on thermoelectric generation. If heat transfer is unequal to thermoelectric modules, we could not get the maximum thermoelectric power. So, by experiment, we analysed the differences of power generation according to the state of the contact between thermoelectric module and heat source. And with the variation of heat transfer area, the generated power was analysed also. Using the experimental results we proposed a thermoelectric generation system.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.32 no.5A
• /
• pp.409-416
• /
• 2007

In cellular orthogonal frequency division multiplexing (OFDM) networks, co-channel interference (CCI) leads to severe degradation in the BER performance. To solve this problem, maximum-likelihood estimation (MLE) CCI cancellation scheme has been proposed in the literature. MLE CCI cancellation scheme generates weighted replicas of the transmitted signals where weights represent the estimated channel transfer functions. The replica with the smallest Euclidean distance from the received signal is selected and data are detected. When the received power of the desired and interference signals are nearly the same, the BER performance is degraded. In this paper, we propose a closed-loop power control (PC) scheme capable of detecting the equal received power situation at the mobile station (MS) receiver by using the newly introduced parameter power ratio (PR). When this situation is detected, the MS sends a feedback to the desired base station (BS) which boosts the transmission power in the next frame. At cell edge where signal to interferer ratio (SIR) is considered to have average value between -5 dB and 10 dB, computer simulations show that the proposed CCI cancellation scheme has a gain of 7 dB at 28 Km/h.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.12 no.5
• /
• pp.55-60
• /
• 2012

Longitudinal transmission-line modal theory is applied to analyze maximum power transfer in plasmonic grating-assisted directional couplers (P-GADC) based on silicon waveguide. By defining a coupling efficiency amenable to rigorous analytical solutions and interference between even and odd modes, the power exchange of TE modes as a function of propagation distance is evaluated. The numerical result reveals that maximum power transfer occurs at a grating period ${\Lambda}_{eq}=10.26{\mu}m$, in which the insertion loss of supermodes is equal to each other. That is, it is generally different from conventional phase-matching condition or minium gap condition of GADC.

• Membrane Journal
• /
• v.14 no.2
• /
• pp.142-148
• /
• 2004

This paper presents the enhancement of oxygen transfer efficiency using vibrating intravascular lung assist device (VIVLAD) for patients having chronic respiratory problems. The flow rate was controlled by the pump and monitored by a built-in flow meter. The vibration apparatus was composed of a piezo-actuator, a function generator, and a power amplifier. Gas flow rates of up to 6 L/min through the 120-cm-long hollow fibers have been achieved by exciting a piezo-actuator. The output PVDF sensor and FRF (frequency response function) were investigated by various frequency in VIVLAD. As a result, the maximum oxygen transfer rate was found to occur with maximum amplitude and the transfer of vibration to the hollow fiber membranes. It was excited by the frequency band of 35 Hz at various distilled water flow rates, and various module types.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.18 no.5
• /
• pp.169-173
• /
• 2004

This paper presents the basic application idea of superconductor cable for voltage stability limited power system. In bulk power system, the transfer capability of transmission line is often limited by the voltage stability, and superconductor cable could be one of the countermeasure to enhance heat transfer limit as well as voltage stability limit. Steady state voltage stability approach by P-V curve is used to calculate the maximum transfer capability of initial system and superconductor applied system. IEEE-14 bus system is used to demonstrate its applicability.

• Proceedings of the KSME Conference
• /
• 2000.04b
• /
• pp.199-204
• /
• 2000

A low temperature differential model stirling engine is manufactured, and its operation characteristics are measured and analyzed by SIMPLE analysis model, in which heat transfer processes are simply considered. The heat transfer coefficients between working fluid and heat sources in the analysis are estimated by comparing the P-V diagrams by experiment and by analysis. This result may be very useful for further design and manufacture of model Stilting engines as well as real engines because it provides a comparatively correct predictions of the operation conditions and power output. It will be also conveniently used as an educational material for mechanical engineering students because it can be a nice example of optimal design process to decide the phase angle and compression ratio of engine design with a simple but realistic simulation.

• Journal of Power Electronics
• /
• v.17 no.1
• /
• pp.305-313
• /
• 2017

A novel interference isolation method is proposed by using several designed coils in capacitive power transfer systems as isolation impedances. For each designed coil, its stray parameters such as the inter-turn capacitance, coil resistance and capacitance between the coil and the core, etc. are taken into account. An equivalent circuit model of the designed coil is established. According to this equivalent circuit, the impedance characteristic of the coil is calculated. In addition, the maximum impedance point and the corresponding excitation frequency of the coil are obtained. Based on this analysis, six designed coils are adopted to isolate the interference from power delivery. The proposed method is verified through experiments with a power carrier frequency of 1MHz and a data carrier frequency of 8.7MHz. The power and data are transferred parrallelly with a data carrier attenuation lower than -5dB and a power attenuation on the sensing resistor higher than -45dB.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.41 no.11
• /
• pp.1574-1579
• /
• 2016

This paper presents a self-powered sensor-node scheme using a RF wireless power harvesting techniques for improve drone time of flight. Sensor-node that is proposed is turned when two conditions satisfy: The one is input RF ID data from master-node should be same with sensor-node's ID, and the other one is RF wireless power harvesting system is turned on by hysteresis switch. In this paper, master-node's output is 26 dBm at 263 MHz. Maximum RF to DC power conversion efficiency is about 55% at 4-6 dBm input power condition (2 meter from master-node). The maximum RF wireless power harvesting range is about 13 meter form master-node. And power consumption of the sensor-node's load elements such as transmitter, MCU and temperature sensors is approximately average 15 mA at 5.0 V for 10 msec.

• Journal of Electrical Engineering and Technology
• /
• v.5 no.3
• /
• pp.389-399
• /
• 2010

Available transfer capability (ATC) is a measure of the transfer capability remaining in a transmission system. Application of unified power flow controllers (UPFCs) could have positive impacts on the ATC of some paths while it might have a negative impact on the ATC of other paths. This paper presents an approach to evaluate the impacts of UPFCs on the ATC from a cost/worth point of view. The UPFC application worth is considered as the maximum cost saving in enhancing the ATC of the paths due to the UPFC implementation. The cost saving is considered as the cost of optimal application of other system reinforcement alternatives (except for UPFC) to reach the same ATC level obtained by UPFC application. UPFC application costs include the maximum cost of alleviating the probable negative impact on the ATC of some paths caused by implementing UPFCs. Optimal system reinforcement is used for systems with UPFCs to determine the aforementioned cost. The proposed method is applied to the IEEERTS and the results are evaluated through a sensitivity analysis. The cost/worth of UPFC application is also used to develop an index for optimal UPFC location and the results are compared with those of other indices. A comparison is finally made with the results obtained using an existing ATC allocation profit-based approach to determine UPFC application worth.