• Korean Journal of Optics and Photonics
• /
• v.19 no.5
• /
• pp.381-385
• /
• 2008

We have analyzed the effect of the substrate removal and packaging schemes on light output characteristics in InGaN/Sapphire LEDs. The removal of the sapphire substrate helps to dissipate the heat generated in the junction, but the advantage comes only with the detrimental effect of degrading the photon extraction efficiency. If the substrate-removed chip is attached to a metallic mount with good thermal conductivity, the maximum driving current is increased drastically, producing significantly increased light output and therefore compensating the photon extraction efficiency degradation. On a dielectric mount with a relatively poor thermal conductivity, however, it produces smaller light output, over most input current range, than the regular type of chips with the sapphire substrate remaining. Thus, for low power applications, the regular chips may be preferred over the substrate-removed chips, regardless of the chip mounts employed.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2007.06a
• /
• pp.9-10
• /
• 2007

In this paper, we investigated the effect of solar cell breakage on maximum output power of PV module. The test result using artificial light source didn't give any change in output power in case of crack near electrical ribbon. Also, there was a reduction in output power in case of increasing of crack area far from electrical ribbon. But, this experiment is under artificial light source test method. So, when such a PV module is outdoor for a long time, there would be problems on electrical output power and durability because of thermal aging phenomenon of solar cell breakage.

• Journal of Power Electronics
• /
• v.18 no.4
• /
• pp.975-984
• /
• 2018

This work presents a high efficiency phase shifted full bridge (PSFB) DC-DC converter for use in the second stage of a battery charger for neighborhood electrical vehicle (EV) applications. In the design of the converter, Lithium-ion battery cells are preferred due to their high voltage and current rates, which provide a high power density. This requires wide range output voltage regulation for PSFB converter operation. In addition, the battery charger works with a light load when the battery charge voltage reaches its maximum value. The soft switching of the PSFB converter depends on the dead time optimization and load condition. As a result, the converter has to work with soft switching at a wide range output voltage and under light conditions to reach high efficiency. The operation principles of the PSFB converter for the continuous current mode (CCM) and the discontinuous current mode (DCM) are defined. The performance of the PSFB converter is analyzed in detail based on wide range output voltage and load conditions in terms of high efficiency. In order to validate performance analysis, a prototype is built with 42-54 V / 15 A output values at a 200 kHz switching frequency. The measured maximum efficiency values are obtained as 94.4% and 76.6% at full and at 2% load conditions, respectively.

• Nuclear Engineering and Technology
• /
• v.49 no.3
• /
• pp.592-597
• /
• 2017

Three plastic scintillators of 4.5 cm diameter and 2.5-cm length were fabricated for comparison with commercial plastic scintillators using polymerization of the styrene monomer 2.5-diphenyloxazole (PPO) and 1,4-bis benzene (POPOP). Their maximum emission wavelengths were determined at 426.06 nm, 426.06 nm, and 425.00 nm with a standard error of 0.2% using a Varian spectrophotometer (Agilent, Santa Clara, CA, USA). Compton edge spectra were measured using three gamma ray sources [i.e., cesium 137 ($^{137}Cs$), sodium 22 ($^{22}Na$), and cobalt 60 ($^{60}Co$)]. Energy was calibrated by analyzing the Compton edge spectra. The fabricated scintillators possessed more than 99.7% energy linearity. Light output was comparable to that of the BC-408 scintillator (Saint-Gobain, Paris, France). The fabricated scintillators showed a light output of approximately 59-64% of that of the BC-408 scintillator.

• Korean Journal of Materials Research
• /
• v.33 no.12
• /
• pp.511-516
• /
• 2023

Amorphous In-Ga-Zn-O (a-IGZO) thin film transistors (TFTs) with a coplanar structure were fabricated to investigate the feasibility of their potential application in large size organic light emitting diodes (OLEDs). Drain currents, used as functions of the gate voltages for the TFTs, showed the output currents had slight differences in the saturation region, just as the output currents of the etch stopper TFTs did. The maximum difference in the threshold voltages of the In-Ga-Zn-O (a-IGZO) TFTs was as small as approximately 0.57 V. After the application of a positive bias voltage stress for 50,000 s, the values of the threshold voltage of the coplanar structure TFTs were only slightly shifted, by 0.18 V, indicative of their stability. The coplanar structure TFTs were embedded in OLEDs and exhibited a maximum luminance as large as 500 nits, and their color gamut satisfied 99 % of the digital cinema initiatives, confirming their suitability for large size and high resolution OLEDs. Further, the image density of large-size OLEDs embedded with the coplanar structure TFTs was significantly enhanced compared with OLEDs embedded with conventional TFTs.

• Proceedings of the KIEE Conference
• /
• 2003.07e
• /
• pp.70-74
• /
• 2003

The buck-boost converter is employed as the variable output PFC power stage. From the loss analysis, this topology has a high efficiency from light load to heavy load. A modified input current sensing scheme is presented to overcome the problem of the insufficient phase margin for the PFC circuit near the maximum output voltage. The variable output PFC circuit has a good performance in the wide output voltage range, under both the Boost mode when the output voltage is high and the Buck+Boost mode when the output voltage is low.

• Proceedings of the KIEE Conference
• /
• 1996.07c
• /
• pp.1421-1423
• /
• 1996

In this study, the effect of solar cell cover glass on the solar cell performance is evaluated. Silicon solar cell (active area:4*6cm, efficiency:12.6% at AMO condition) is used for this study. ITO(Indium tin Oxide) film thickness of the ITO/AR/substrate glass/solar cell structure samples are $40{\AA}$, $60{\AA}$, $160{\AA}$, $240{\AA}$ respectively. The solar cell maximum output power on the stacking structure variations showed 465mW in the AR/ITO/substrate glass/solar cell, and minimum output power showed 403mW in the AR/substrate glass/solar cell. The maximum output power of the solar cell on the ITO thickness variations of the ITO/AR/substrate glass/solar cell showed 460mW at $40{\AA}$ then decrease output power as ITO thickness increase. For environment tests, all samples are exposed UV light in the vacuum chanber. The output power degradation of AR(UVR)/substrate glass/solar cell stacking structure is small compared with ITO/AR(UVR)/substrate glass/solar cell stacking structure.

• Korean Journal of Materials Research
• /
• v.25 no.9
• /
• pp.487-491
• /
• 2015

In photovoltaic power generation where minority carrier generation via light absorption is competing against minority carrier recombination, the substrate thickness and material quality are interdependent, and appropriate combination of the two variables is important in obtaining the maximum output power generation. Medici, a two-dimensional semiconductor device simulation tool, is used to investigate the interdependency in relation to the maximum power output in front-lit Si solar cells. Qualitatively, the results indicate that a high quality substrate must be thick and that a low quality substrate must be thin in order to achieve the maximum power generation in the respective materials. The dividing point is $70{\mu}m/5{\times}10^{-6}sec$. That is, for materials with a minority carrier recombination lifetime longer than $5{\times}10^{-6}sec$, the substrate must be thicker than $70{\mu}m$, while for materials with a lifetime shorter than $5{\times}10^{-6}sec$, the substrate must be thinner than $70{\mu}m$. In substrate fabrication, the thinner the wafer, the lower the cost of material, but the higher the cost of wafer fabrication. Thus, the optimum thickness/lifetime combinations are defined in this study along with the substrate cost considerations as part of the factors to be considered in material selection.

• Journal of the korean academy of Pediatric Dentistry
• /
• v.28 no.3
• /
• pp.363-368
• /
• 2001

It is well known that numerous factors influence the light output of curing units, but many dentists are un aware that the output of their curing lights are inadequate. This study was conducted to evaluate the light in tensity of visible-light curing units in some private dental clinics and hospital dental clinics. In order to determine the maximum light intensity of the curing units, lamps, filters and fiber optic bundles, they were replaced with new ones and light intensity was remeasured. Light intensity was measured by employing a digital radiometer (EFOS model #8000, USA). Light intensity ranged in $29\sim866mW/cm^2$ (below $150mW/cm^2$ ; 17.8%, $150\sim300mW/cm^2$ : 46.6%, above $300mW/cm^2$ ; 35.6%). The replacement of the components increased the light intensity, with maximum increases of 94.8% for lamps, 82.3% for filters, 200.8% for fiber optics and 361.5% for all three parts. According to the manufacturer of radiometer, curing light is considered as unsuitable for use with a reading of above $300mW/cm^2$ by the radiometer. Applying these criteria to the present study, 64.4% of the curing units required repair or replacement. The results of this study indicated that the light intensities of the curing units used in dental practice were lower than optimum level.

• New & Renewable Energy
• /
• v.5 no.3
• /
• pp.26-31
• /
• 2009

Using MBE growth method, GaAs/AlGaAs solar cell structure was grown. Deposited electrodes are Au/Ni/Ge for n-type and Au/Pt/Ti for p-type electrodes were deposited by E-beam evaporator. Indoor light concentrators were devised and fabricated in order to concentrate artificial solar rays. Also mirror and prism and Fresnel lens concentration system with solar simulator were devised and fabricated. Results of solar cell characteristics were measured with shutting system which can control the amount of light. Maximum power density was 2.13 W/$cm^2$ and maximum concentration was 124 sun, when mirror with Fresnel lens was used at $7854\;mm^2$ of shutter hole.