• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.21 no.6
• /
• pp.524-529
• /
• 2008

In this paper, in order to develop low loss multilayer actuator, piezoelectric properties of PZW-PMN-PZT multilayer actuator sintered at $900^{\circ}C$ low temperature were investigated according to the number of multilayer. The multilayer actuator was fabricated using tape casting method and used pure Ag internal electrode. The density above $8.0\;g/cm^3$ was obtained at all specimens. With increasing number of multilayer, effective electromechanical coupling factor($k_{eff}$) was increased. $k_{eff}$ of multilayer actuator shows the maximum value of 0.283 at 11 layers actuator. However, effective mechanical quality factor(Qm') was decreased according to the increase of number of multilayer. The Qm' of multilayer actuator showed the maximum value of 920 at 5 layers actuator.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2006.06a
• /
• pp.325-326
• /
• 2006

In this study, in order to develop piezoelectric device for multilayer piezoelectric ultrasonic motor, low temperature sintering $Pb(Mn_{1/3}Nb_{2/3})_{0.02}(Ni_{1/3}Nb_{2/3})_{0.12}(Zr_{0.48}Ti_{0.52})_{0.86}O_3$ system ceramics were fabricated according to the variations of forming pressure of casting sheet. At the 300[$kgf/cm^2$] forming pressure, the maximum density of 7.8[$g/cm^3$] was obtained. At the 350[$kgf/cm^2$] forming pressure, the maximum values of effective electromechanical coupling factor $k_{cff}\;=\;0.24$ and mechanical quality factor Qm=628 were obtained.

• Korean Journal of Fisheries and Aquatic Sciences
• /
• v.12 no.3
• /
• pp.161-166
• /
• 1979

To know the influence of temperature on the fermentation process, a strain of Lactobacillus bulgarius was experimentally cultured three different temperature conditions of $39^{\circ}C,\;42^{\circ}C\;and\;45^{\circ}C$, pH 5.8 and mechanical agitation of 500rpm. During 20 hour's fermentation, the microbial growth attained the maximum concentration under the conditions mentioned above. However, the culturing conditions resulted different outcomes in terms of maximum concentration of the microbes and the residual concentration of substrate. Among the three temperature conditions, the fermentation at $45^{\circ}C$ was most effective and the maximum specific growth temperature conditions, the fermentation at $45^{\circ}C$ was most effective and the maximum specific growth rate was 0.58/hr. Activation energy deduced from the Arrhenius equation was 9,220cal/mole and entropy was $-33.74\;cal/^{\circ}K$ mole. Activation enthalpy was 9,845 cal/mole and free energy was 19,800 cal/mole.

• Atmosphere
• /
• v.20 no.4
• /
• pp.427-436
• /
• 2010

The single-scattering optical properties of ice crystals in cirrus clouds by the aircraft measurement data were investigated, and the radiative equilibrium temperatures and radiative fluxes were calculated and analyzed by radiative convective model with the variations of ice crystal habits and sizes in cirrus clouds. The homogeneous cloud is assumed to be in the layer 200~260 hPa with an ice crystal content of $10gm^{-2}$ for the flux calculation. The profiles of temperature, humidity, and ozone typical of mid-latitude summer are used. The surface albedo is assumed to be 0.2 for all spectral bands and the cosine of solar zenith angles is 0.5. The result of radiative equilibrium temperature at surface was less than surface temperature of the standard atmosphere data in case of smaller effective ice crystal size and larger optical thickness. The column, aggregation and plate in 6 ice crystal habits were the most effective in positive greenhouse effect and bullet-4 was the worst in it. At the surface, the maximum difference of equilibrium temperature by 6 kinds of ice crystal habits were about 3~15 K with 30 sample aircraft measurement data.

• Nuclear Engineering and Technology
• /
• v.53 no.11
• /
• pp.3653-3664
• /
• 2021

In PWR three-dimensional transient coupling calculation software CORCA-K, the nodal Green's function method and diagonal implicit Runge Kutta method are used to solve the spatiotemporal neutron dynamic diffusion equation, and the single-phase closed channel model and one-dimensional cylindrical heat conduction transient model are used to calculate the coolant temperature and fuel temperature. The LMW, NEACRP and PWR MOX/UO₂ benchmarks and FangJiaShan (FJS) nuclear power plant (NPP) transient control rod move cases are used to verify the CORCA-K. The effects of burnup, fuel effective temperature and ejection rate on the control rod ejection process of PWR are analyzed. The conclusions are as follows: (1) core relative power and fuel Doppler temperature are in good agreement with the results of benchmark and ADPRES, and the deviation between with the reference results is within 3.0% in LMW and NEACRP benchmarks; 2) the variation trend of FJS NPP core transient parameters is consistent with the results of SMART and ADPRES. And the core relative power is in better agreement with the SMART when weighting coefficient is 0.7. Compared with SMART, the maximum deviation is -5.08% in the rod ejection condition and while -5.09% in the control rod complex movement condition.

• Water Engineering Research
• /
• v.6 no.1
• /
• pp.1-15
• /
• 2005

The numerical model, FLUENT, was employed to investigate the effect of the heated water discharged from the diffuser of Boryung Power Plant. Temperature patterns of the thermal effluent discharged from two proposed types of the diffusers was evaluated for maximum flood and maximum ebb tide. The hydraulic model experiments were also performed in the reduced scale of 1/150 to verify the numerical simulation results. The buoyant jets discharged from the diffusers were found to be significantly affected by the ambient flows beyond the region where the effluent momentum was dissipated. Both the numerical and experimental results showed that the area of the excess isotherm for Type 1 diffuser was larger than that for Type 2 diffuser. Type 2 diffuser system was observed to be a more effective diffuser design than Type 1 diffuser system based on the temperature reduction and excess isotherm obtained from the numerical simulation in the ambient flows.

• Tribology and Lubricants
• /
• v.11 no.1
• /
• pp.27-36
• /
• 1995

Maximum allowable PV values of oilless composite bearing materials (70% epoxy-resin/30% Graphite) were measured and compared at various types of test rigs that have different contact geometry and the operating conditions. Test results showed that material failure was mainly characterized by the sharp increase in both coefficient of friction and surface temperature, and different PV values were measured under different Contact geometry. The discrepancy in measurement of PV values was analyzed in the light of theoretical frictional heating analysis. Results show that surface temperature rise depends on its contact geometry, and PV values could be overestimated in the testing conditions of high sliding velocity. Test data of different contact geometry were normalized by using a normalized contact pressure and sliding velocity; it showed a good correlation. This work suggests that normalized PV values could be more effective in evaluating bearing materials than conventional PV values for a design parameter of journal bearings.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2007.11a
• /
• pp.270-271
• /
• 2007

In this study, piezoelectric properties of PZW-PMN-PZT multilayer actuator sintered at $900^{\circ}C$ low temperature have been investigated. The multilayer actuator was fabricated by tape casting methods. The density above $8[g/cm^3]$ was obtained at all the specimens. Also, according to increasing the number of multilayer, effective electromechanical coupling factor$(k_{eff})$ showed increasing trend. The $k_{eff}$ of multilayer actuator showed the maximum value of 0.283 at 11 layer. However, according to increasing the number of multilayer, mechanical quality factor(Qm') showed decreasing tend. The Qm' of multilayer actuator showed the maximum value of 920 at 5 layer.

• Proceedings of the KSME Conference
• /
• 2000.04b
• /
• pp.311-315
• /
• 2000

A numerical investigation is made of time-dependent buoyant convection in a square of a non-Boussinesq fluid. The density-temperature$({\rho}-T)$ relation is modeled by a quadratic function, with the maximum density ${\rho}_M$ at temperature $T_M$. The horizontal walls of the square are insulated, and a pulsating temperature $T_H=T_M+{\Delta}T'\;sin({\omega}{\tau})$ is imposed on the hot vertical sidewall. The temperature at the cold wall $T_c$ is constant. Extensive numerical solutions to the governing Navier-Stokes equations are portrayed. Resonance is identified by monitoring the amplitude of the mid-plane Nusselt number, $A(Nu^*)$. The primary resonance frequency is found by matching ${\omega}$ to the nondimensional basic mode $N_1$ of internal gravity oscillations. Due to the quadratic$({\rho}-T)$ relationship, the effective pulsation frequency for density, $2{\omega}$, is meaningful, which brings forth the secondary resonance frequency, i.e., $2{\omega}=N_1$

• Journal of Microbiology and Biotechnology
• /
• v.14 no.2
• /
• pp.312-316
• /
• 2004

Five strains, producing bacterial thermostable L-arabinose isomerase, were isolated from Korean soil samples obtained from compost under high temperature circumstances. Among these strains, the CBG-Al showed the highest L-arabinose isomerase activity at $60^\circ{C}$ and was selected as a D-tagatose producing strain from D-galactose. This strain was identified as Geobacillus thermodenitrificans based on the 16S rRNA analysis, and biological and biochemical characteristics. The isolated strain was aerobic, rod-shaped, Gram-positive, nonmotile, and an endospore-forming bacterium. No growth was detected in culture temperature below $40^\circ{C}$. The maximum growth temperature and maximum temperature of enzyme activity were $75^\circ{C}$ and $65^\circ{C}$, respectively. In metal ion effects, $Ca^{2+}$ was the most effective enzyme activator with the reaction rate by 150%. In a 5-1 jar fermentor with 3-1 MY medium, L-arabinose isomerase activity was growth-associated and pH decreased rapidly after the initial logarithmic phase.