• Journal of IKEEE
• /
• v.21 no.2
• /
• pp.166-169
• /
• 2017

In this paper, maximum boost discrete PWM(DPWM) method of Z-Source Inverter(ZSI) is proposed. In general, a DPWM method is used to reduce the switching losses of the inverters and increase the efficiencies. The maximum boost PWM method of Z-Source Inverters is combined with the DPWM method. The proposed Maximum boost DPWM of ZSI is analyzed and it shows how to reduce the switching losses of ZSI. An experimental system has been built and tested to verify the effectiveness of the proposed method.

• Proceedings of the KIEE Conference
• /
• 2002.11d
• /
• pp.286-293
• /
• 2002

Photovoltaic systems normally use a maximum power point tracking (MPPT) technique to continuously deliver the highest possible power to the load when variations in the insolation and temperature occur. A simple method of tracking the maximum power points (MPPs) and forcing the boost converter system to operate close to these Points is presented through deriving small-signal model and transfer function of boost converter. This paper aims at modeling boost converter including equivalent series resistance of input reservoir capacitor by state-space-averaging method and PWM switch model. In the future, properly designed controller for compensation will be constructed in real system for maximum photovoltaic power tracking control.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2011.10a
• /
• pp.404-407
• /
• 2011

This paper presents a design of current mode PWM/PFM DC-DC Boost converter. This DC-DC Boost Converter operates with PWM mode at the heavy loads and with PFM mode at light loads. The DC-DC boost converter is designed with CMOS 0.35${\mu}m$ technology. It operates at 500KHz and can drive a load current up to 600mA. It has a maximum power efficiency of 92.1%. The total chip area is $1300{\mu}m{\times}1070{\mu}m$ including pads. The DC-DC boost converter operates in a wide range of load currents while occupying a small chip area.

• Proceedings of the KIEE Conference
• /
• 2003.04a
• /
• pp.341-348
• /
• 2003

Photovoltaic systems normally use a maximum power point tracking (MPPT) technique ta continuously deliver the highest possible power to the load when variations in the insolation and temperature occur. A simple method of tracking the maximum power points (MPPs) and forcing the boost converter system to operate close to these points is presented through deriving small-signal model and transfer function of boost converter. This paper aims at modeling boost converter including equivalent series resistance of input reservoir capacitor by state-space-averaging method and PWM switch model with properly designed controller for maximum photovoltaic power tracking control.

• Journal of IKEEE
• /
• v.16 no.3
• /
• pp.203-210
• /
• 2012

Since the non-overlapping gate driver used in conventional DC-DC boost converters generates fixed dead-times, the converters suffer from the body-diode conduction loss or the charge-sharing loss. To reduce the efficiency degradation due to these losses, this paper presents a PWM DC-DC boost converter with adaptive dead-time control. The proposed DC-DC boost converter delivering 3.3V output from a 2.5V input is designed with CMOS $0.3{\mu}m$ technology. It operates at 500kHz and has a maximum power efficiency of 97.3%.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.48 no.10
• /
• pp.15-19
• /
• 2011

We have proposed a maximum power point tracking (MPPT) circuit for thermoelectric generator (TEG) using a Boost converter. The key point of the proposed MPPT circuit is that the duty ratio of the boost converter automatically moves to Maximum Power Point by comparing of consecutive sampling voltage using two comparators. From the simulation results, we showed that the proposed circuit can find the maximum power point within 2 CLK periods and to generate optimal PWM signal within 3 CLK periods. The proposed MPPT circuit was designed by using a CMOS 0.18 um process, and it is now on the fabrication.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2012.10a
• /
• pp.285-288
• /
• 2012

Since the non-overlapping gate driver used in conventional DC-DC boost converters generates fixed dead-times, the converters suffer from the body-diode conduction loss or the charge-sharing loss. To reduce the efficiency degradation due to these losses, this paper presents a PWM DC-DC boost converter with adaptive dead-time control. In light loads, power switching is also employed to increase the efficiency. The designed DC-DC boost converter can thus achieve high efficiency at wide current range. The proposed DC-DC boost converter has 3.3V output from a 2.5V input with 0.18um technology. It operates at 500KHz and has a maximum power efficiency of 97.8%.

• Journal of IKEEE
• /
• v.19 no.1
• /
• pp.73-79
• /
• 2015

In this paper, maximum boost space vector pulse-width modulation(MBSVPWM) strategy of Z-Source Inverters(ZSIs) is proposed. Conventional space vector pulse-width modulation(SVPWM) method of Voltage Source Inverters(VSIs) is modified to produce unique PWM patterns that realize the maximum boost control of ZSIs. This proposed method minimizes the switching power losses of ZSIs by reducing the numbers of the shoot-through states. Moreover, some switches keep ON state and the switching transitions do not occur during the specific sectors. An experimental system has been built and tested to verify the effectiveness of the proposed strategy.

• The Transactions of the Korean Institute of Electrical Engineers B
• /
• v.55 no.4
• /
• pp.224-230
• /
• 2006

The conventional way to implement a bidirectional converter with boost/buck has been to use two general purpose PWM ICs with a single supply voltage. In this case, when one direction mode is in operation, the other is disabled and the output of the error amplifier of the disabled IC may be saturated to a maximum value or zero. Therefore, during mode transition, a circuit which can disable the switching operation for a certain time interval is required making it impossible to get a seamless transition. In this paper, the limitations of the conventional 42V/14V bi-directional DC/DC converter implemented with general current mode PWM ICs with a single supply voltage are reviewed and a new current mode PWM controller circuit with a dual voltage system is proposed. The validity of the proposed circuit is investigated through simulation. and experiments.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.17 no.6
• /
• pp.471-477
• /
• 2012

In this paper, in order to use module integrated converter using cascaded buck-boost converter for a low battery charger in stand-alone system, a charging algorithm which considers photovoltaic and battery status and PWM controllers which are changed according to charging modes are proposed. The proposed algorithm consists of constant current mode, constant voltage mode and maximum power point tracking mode which enables the battery to charge with maximum power rate. This paper also presents design of cascaded buck-boost converter that is the photovoltaic charger system. A 150W prototype system is built according to verify proposed the charger system and the algorithm.