• 한국정밀공학회지
• /
• 제27권3호
• /
• pp.80-88
• /
• 2010

A simple computational model for modeling of subsurface crack growth under cyclic contact loading is presented. In this model, it is assumed that the initial fatigue crack will initiate in the region of the maximum equivalent stress at certain depth under the contacting surface. The position and magnitude of the maximum equivalent stress are determined by using the equivalent contact model, which is based on the Hertzian contact conditions with frictional forces. The virtual crack extension method is used for simulation of the fatigue crack growth from the initial crack up to the formation of the surface pit due to contact fatigue. The relationships between the stress intensity factor and crack length are then determined for various combinations of equivalent contact radii and loadings.

• 한국산학기술학회논문지
• /
• 제7권3호
• /
• pp.265-270
• /
• 2006

복합재로 된 판재에 대하여 동적 균열이 접합면을 따라서 진행되어 가면서 찢어져 나갈 때 그 계면 주위에서의 응력 상태 및 변형, 견인응력 등을 조사하였다. 최대의 등가응력 및 소성 변형율은 접촉이 바로 떨어지는 부분에서 그리고 판 끝부분의 휘어지는 부근에서 최대의 변형량이 되었다. 견인력은 0.015mm정도로 그 면이 떨어졌을 때 최대치 75 MPa로서 되었다가 서서히 낮아지면서 0.13mm이상 떨어졌을 때는 0으로 일정하게 되었다. 이러한 연구 자료로서 정확한 파괴강도 해석과 안전설계 및 새로운 고급재료의 개발에 필요한 자료를 제공할 수 있는 기초적인 연구를 수행함이 본 연구의 목적이다.

• 한국기계가공학회지
• /
• 제8권2호
• /
• pp.40-45
• /
• 2009

This study is analyzed by stress contour of automotive tire at contact on road surface. Maximum equivalent stress as 61200Pa is shown on the lower mid part in case of tire contacted on road surface. As the air pressure of tire increases, maximum total deformation as 5mm is shown on the side part of tire. It can be shown that the side part of tire is unstabilized. There is no load effect on tire at its upper and lower directions. When the moment applied on the side of tire is increased 1.4 times as its value, the value of maximum principal stress is increased 1.4 times. The stress at the tire is in proportion to the moment applied on the its side. The tire tends to incline toward its side by this moment.

• 한국생산제조학회지
• /
• 제18권5호
• /
• pp.477-482
• /
• 2009

This study analyzes the result with dynamic simulation about deformation according to time when a car impacts bollard. These results are shown as followings. The maximum deformation is shown at the lower part of front grass in case of the impact of front or passenger seat but this deformation is shown at the lower part of rear bumper in case of double impact. The maximum equivalent stress is shown at the upper part by the side grass of driver seat at the elapsed time of 0.00075 second after impact in case of the impact of front or passenger seat but this deformation is shown at the front bonnet at the elapsed time of 0.004 second after the additional impact in case of double impact. The maximum total deformation or equivalent stress is shown nearly same in case of the impact of front or passenger seat. But the value of this deformation or equivalent stress in case of the impact of front or passenger seat is shown with 2 times or more than 17% respectively as this value in case of double impact.

• 한국기계가공학회지
• /
• 제7권2호
• /
• pp.66-71
• /
• 2008

The data of the deformation and the stress according to time are studied at upper model of press and lower model of the blanking plate applied by press with the width, length and height of 0.4 m and 0.6 m respectively. The press is pushing downward on the plate fixed at the lower floor. These data are compared and investigated through this study. By using these results, there is the maximum deformation at 4 corners in the lower plate model of aluminium alloy fixed at lower floor. This deformation incase of elapsed time of 0.6 second becomes 4 times as much as in case of elapsed time of 0.2 second. The quantity of deformation at the lower plate model becomes more than at the upper press model to the extent of 10%. At the lower plate model of aluminium alloy, there is the maximum Von-Mises equivalent stress at 4 corners and both sides of middle area on the lower plate model of aluminium alloy. This stress in case of elapsed time of 0.6 second becomes 6 times as much as in case of elapsed time of 0.2 second. The Von-Mises equivalent stress of lower plate model becomes 2 times as much as that of upper press mode.

• 한국생산제조학회지
• /
• 제20권5호
• /
• pp.528-534
• /
• 2011

This study analyzes thermal stress and durability fatigue on the modelling of EGR valve. In case of 10% opening at its inlet, the minimum temperature gets cool as 3 times as inlet temperature. The maximum equivalent stress becomes lowest as the value of $2.6274{\times}109$ Pa and fatigue life becomes highest as 23.657 Cycle. But the minimum temperature gets cool as 2.2 times as inlet temperature in case of 50% opening at its inlet. The equivalent stress becomes higher and fatigue life becomes lower than in case of 10% opening. In case of 100% opening at its inlet, the minimum temperature gets cool as 0.2 times as inlet temperature. The equivalent stress becomes lower and fatigue life becomes higher than in case of 50% opening. Maximum equivalent stress and total deformation are shown at the closing of EGR valve by the pressure of inflow gas. The structural analysis result of this study can be effectively utilized with the design of EGR valve by investigating prevention and durability against its damage.

• 한국세라믹학회지
• /
• 제31권10호
• /
• pp.1141-1146
• /
• 1994

Cyclic fatigue experiment was carried out to predict the life time of alumina ceramics. Four kinds of model were suggested to obtain the adequate representative static stress corresponding to the cyclic stress applied to the alumina specimens. Arithmetic mean stress model gives 21.81 of the crack growth exponent, integrated stress model gives 22.15, maximum stress model gives 24.57, and equivalent static stress model gives 24.43. It is considered that the equivalent static stress model is the most reasonable and gives the best adequate crack growth exponents value.

• 한국생산제조학회지
• /
• 제18권3호
• /
• pp.279-284
• /
• 2009

This study investigates the stress at gear by modelling differential gear and using FEM. When gear is driven under power, high equivalent stress of 1596.2MPa is occurred at the stationary shaft. Maximum equivalent stress of 1596.2MPa is also occurred at the bottom and root of tooth and its fatigue life becomes 12.4 as the shortest cycle. As much as it becomes away from the center of gear, the maximum deformation becomes occurred. As exact power is delivered with the precise design of gear, the loss of power energy can be decreased.

• 한국자동차공학회논문집
• /
• 제21권6호
• /
• pp.166-174
• /
• 2013

This study investigates the strength durability on the results of structural and vibration analysis due to the shape of excavator wheel. As model 2 has the least stress by comparing three models with maximum equivalent stress, model 2 has most durability among three models at static analysis. Maximum equivalent stress is shown at the bottom part contacted with ground and this part on wheel is most affected by load in cases of all models. Safety factor can be decided with the value of 2.3 by considering the yield stress of this model. The range of maximum harmonic response frequencies becomes 6900 to 7000Hz. As model 2 has the least total deformation and equivalent stress at these critical frequencies, model 2 has the most durability at vibration analysis among three models. The structural and vibration analysis results in this study can be effectively utilized with the design of excavator wheel by investigating prevention and durability against its damage.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2002년도 추계학술대회 논문집
• /
• pp.210-213
• /
• 2002

The Purpose of this study is to know temperature and thermal stress distribution in specimens during processing of WEDM. If it is constant to the cutting speed and the thickness of material, it is very important to the effect of temperature and the thermal stress distribution after cutting processing. This paper show the analysis result of the distribution of temperature and the residual stress along the direction of thickness before processing of WEDM and after when the cooling temperature is$20^{\circ}C$. The maximum temperature of edge of specimens is $1600^{\circ}C$. It has little temperature gradient in the depth which is 5mm away from edge of specimens. Equivalent residual stress is result in 180.7 MPa at maximum temperature.