• Journal of Magnetics
• /
• v.18 no.4
• /
• pp.487-493
• /
• 2013

The automotive industry is showing widespread interest in belt-driven electric motor-assisted (e-Assist) systems. A belt-driven assist system (BAS) starts and assists the combustion engine in place of the conventional generator. In this study, a water-cooled wound rotor synchronous motor (WRSM) for the e-Assist system was designed and analyzed. The performance of the WRSM was compared with that of an interior permanent magnet synchronous motor (IPMSM). The WRSM efficiency can be improved for the BAS by adjusting the field flux at high speeds. The field current map to obtain the maximum efficiency based on the speed and torque was developed. To control the field flux via field current control in the WRSM, a general H-bridge circuit was added to the WRSM inverter to get the rapid current response in the high-speed region; the characteristics were compared with the chopper circuit. A WRSM developed for the belt-driven e-Assist system and a prototype 115 V power electronic converter to drive the WRSM were tested with a 900 cc combustion engine. The test results showed that the WRSM-type e-Assist system had good characteristics and could successfully start and assist the 900 cc combustion engine.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.27 no.3
• /
• pp.291-298
• /
• 2016

In this paper, we studied about the radiated emission of EFT(Electrical Fast Transient)/Burst signal, referenced IEC-61000-4-4 of the international EMC standard and its effect on EUT(Equipment Under the Test) when EFT/Burst signal (Conducted noise) induced on a power cable to EUT. Firstly, we set up test sample by the standard and +4 kV standard signal is induced by EFT/Burst signal generator with 1 m length power cable for 1 minute. Consequently, we found not only induced EFT/Burst signal along power line, but also directly radiated emission signal from EFT/Burst signal generator (Radiated emission noise of EFT/Burst). The radiated emission signal of EFT/Burst was 30 dB which is higher than limit of CISPR 22 which is international EMC standard. Moreover, we measured the electric field strength by changing distance from maximum radiated emission point to electric field strength tester. As a result, this electric field strength was 23 V/m which is higher than international EMC standard test level(CISPR 24). Therefore, it was confirmed that the probability of malfunction may be high when radiated emission of EFT/Burst noise exists near the EUT.

• Journal of the Korean Ceramic Society
• /
• v.41 no.10 s.269
• /
• pp.771-776
• /
• 2004

[ $Ba(Zr_{0.08}Ti_{0.92})O_3$ ] polycrystal was grown by floating zone technique with two ellipsoidal mirrors using the $8\%$of Zr-modified BZT ceramics as both a feed rod and a seed crystal. In order to study the annealing effect, a part of the grown crystal was sliced and annealed in the oxygen atmosphere at $1,200^{\circ}C$ for 10 h. The dielectric constant and loss at 10 kHz, 100 kHz, and 1 MHz were measured in the temperature range between $-100^{\circ}C$ and $150^{\circ}C$ to investigate the dielectric properties of the grown polycrystal. The electric-field dependence of the dielectric constant at 10 kHz and 100 kHz was studied by measuring the dielectric constants as a function of the biased-electric fields which ran from -15 kV/cm to 15 kV/cm. Due to the effect of annealing in the oxygen atmosphere, the electric-field tunability of dielectric constants increased from $47.5\%$ to 5 to and the figure of merit for this material from 39.6 to 46.4. Since the figure of merit can be increased to more than 46.4 by increasing the maximum value of the biased-electric fields to more than 15 V/cm, this material nay have a possibility for applications in microwave tuning devices at room temperature.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.17 no.6 s.109
• /
• pp.501-510
• /
• 2006

In this paper, the electromagnetic coupling through a slit in a flanged parallel-plate waveguide with a conducting strip is studied. The coupled integro-differential equations for the electric field over the slit and the induced current over the strip are derived and solved by use of the method of moments. The characteristics of some types of maximum coupling phenomena are investigated from the examinations of the variations of the equivalent slit admittance and the coupled power against various parameters such as the location of conducting strip, operating frequency, and strip length.

• International Journal of Aerospace System Engineering
• /
• v.9 no.1
• /
• pp.1-15
• /
• 2022

Pyrotechnic initiators provide a source of pyrotechnic energy used to initiate a variety of space mechanisms. Pyrotechnic systems build in electromagnetic environment that may lead to critical or catastrophic hazards. Special precautions are need to prevent a pulse large enough to trigger the initiator from appearing in the pyrotechnic firing circuits at any but the desired time. The EMC verification shall be shown by analysis or test that the pyrotechnic systems meets the requirements of inadvertent activation. The MIL-STD-1576 and two range safeties, AFSPC and CSG, require the safety margin for electromagnetic potential hazards to pyrotechnic systems to a level at least 20 dB below the maximum no-fire power of the EED. The PC23 is equivalent to NASA standard initiator and the 1EPWH100 squib is ESA standard initiator. This paper verifies the two safety margins for electromagnetic potential hazards. The first is verified by analyzing against a RF power. The second is verified by testing against a DC current. The EMC safety margin requirement against RF power has been demonstrated through the electric field coupling analysis in differential mode with 21 dB both PC23 and 1EPWH100, and in common mode with 58 dB for PC23 and 48 dB for 1EPWH100 against the maximum no-fire power of the EED. Also, the EMC safety margin requirement against DC current has been demonstrated through the electrical isolation test for the pyrotechnic firing circuits with greater than 20 dB below the maximum no-fire current of the EED.

• Journal of the Korean Geotechnical Society
• /
• v.19 no.5
• /
• pp.49-58
• /
• 2003

Underground flexible pipes for electric cables are subject to external loads and surrounding soil pressure. Particularly, strain of flexible pipes is of great concern in terms of safety and maintenance for electric cables. In this paper, stress and strain of flexible pipes with various installation depth are compared using traditional formula, FEM analysis, model soil box test and field test. from the findings of various analyses, considering the strain criteria-maximum 3.5%, it is suggested that flexible pipes can be buried at the depth of 80cm without additional soil improvement.

• Journal of the Korean Magnetics Society
• /
• v.7 no.5
• /
• pp.225-231
• /
• 1997

Sulphur Spinel $Co_{0.95}Fe_{0.05}Cr_2S_4$ has been studied with Mossbauer Spectroscopy between 4.2 K and room temperature. The $Fe^{2+}$ ion in a tetrahedral site is the Jahn-Teller active and the dynamic Jahn-Teller distortion starts below the magnetic ordering temperature. The distortion cause a quadrupole shift to appear which increases with decreasing temperature. The magnetic hyperfine field has a maximum at 100 k and then decreases with decreasing temperature. The magnitude of the interaction ratio R between the electric quadrupole and magnetic dipole interaction increases from 0 near the magnetic ordering temperature to 5.4 at 4.2 K. The optimum values of 0, the polar angle of the magnetic hyperfine field with respect to the principle axis of the electric field gradient (EFG) remains zero and the asymmetry of the EFG n is about 0.25. The simulations of Mossbauer spectra coincidence with the experimental results.

• Korean Journal of Materials Research
• /
• v.9 no.6
• /
• pp.551-555
• /
• 1999

The deposition condition to obtain stoichiometric $Ta_2$O\ulcorner films, which is still controversial, using magnetron reactive sputtering was studied. The films were deposited by varying $O_2$gas flow rate with sputtering power and Ar gas flow rate of 200W and 60 sccm fixed. At the conditions of $O_2$ gas flow rate over 20 sccm, amorphous Tantalum oxide films with the refractive index of 2.1 and dielectric constant of 25 were deposited. Among those films, the capacitors dielectric properties of the film deposited at the condition of $O_2$ gas flow rate 50 sccm was best, the leakage current was 1$\times$10\ulcornerA/$\textrm{cm}^2$ at the electric field strength of 0.5 MC/cm and the breakdown field strength was over 2.0 MV/cm. This result could be explained from the analysis comparing with a standard sample using RBS because the composition of the film deposited at this condition was closest to the stoichiometric $Ta_2$O\ulcorner. The result of XPS analysis convinced that this film was stoichiometric $Ta_2$O\ulcorner film. A maximum cathode voltage was observed when $O_2$gas flow rate was 30 sccm. This shows that the Schiller's proposition that one can obtain stoichiometric films at the condition of maximum cathode voltage is not correct and more oxygen than that of the maximum voltage condition is necessary to deposit the stoichiometric Ta$_2$O\ulcorner films.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.47 no.4
• /
• pp.300-308
• /
• 2019

For drones to be used for industrial or agricultural applications, it is necessary to increase the payload and endurance. Currently, the payload and endurance are limited by the battery technology for electric powered drones. In addition, charging or replacing the batteries may not be a practical solution at the field that requires near continuous operation. In this paper, a procedure to optimize the power system of an electric hybrid drone that consists of an internal combustion engine, a generator, a battery, and electric motors is presented. The example drone for crop dusting is sized for easy transportation with a maximum takeoff weight of 200 kg. The two main rotors that are mechanically connected to the internal combustion engine provides most of the lift. The drone is controled by four electric motors that are driven by the generator. By analyzing the flow of the energy, a methodology to select the optimum propeller and motor among the commercially available models is described. Then, a procedure of finding the optimum operational condition along with the proper gear reduction ratios for the internal combustion engine based on the test data is presented.

• Journal of the Korean Ceramic Society
• /
• v.35 no.7
• /
• pp.679-684
• /
• 1998

Dielectricand pyroelectric properties of {{{{ { { {Ba }_{0.67 }Sr }_{0.33 } }`TiO_{3 } ^{ } }} (BST) thin plates and films were investigated. For BST thin plates maximum dielectric constant and pyrolelectric coefficient were observed at around 24$^{\circ}C$ and pyroelectric characteristics were improved as applied bias field was increased. When the electric field of 4kV/cm was applied to the thin plates sintered at 140$0^{\circ}C$ the pyroelectric coefficients over 4$\times$10-7C/{{{{ { cm}^{2 }K }} were obtained in the range of 0-4$0^{\circ}C$ BST thin films deposited using rf magnetron sputtering showed [001] preferred orientation at substrate temperatures above 50$0^{\circ}C$ On the contrary to the thin plates the dielectric constants of the thin films gradually increased above 15$^{\circ}C$ and decreased as applied bias field in-creased. The pyroelectric coefficients of thin films were lower than 1/10 those of thin plates.