• 한국CDE학회논문집
• /
• 제17권1호
• /
• pp.1-6
• /
• 2012

The End Coupling is main component of the aluminum hot roll process. The End Coupling is used for transmission of rotational power with heavy-duty load. Fracture of the End Coupling cause serious economic losses because an End Coupling is a very expensive component and it takes a long time to repair it. Therefore, preventing the destruction of the End Coupling is essential for ensuring a long mechanical life cycle. In this paper, the parametric study on the End Coupling was performed in order to minimize maximum stress under operation loads. To verify the interference of spindle assembly with modified End Coupling, kinematics simulation was performed by applying the various combination type and dynamic boundary condition of the spindle assembly. The interference of optimized model was not occurred during combination process and driving process. As a result of an optimum design for life extension on End Coupling, the maximum stress of modified End Coupling was lower than that of the initial model by 26%.

• 한국전자파학회논문지
• /
• 제15권11호
• /
• pp.1116-1122
• /
• 2004

플랜지된 평행 평판 도파관의 슬릿을 통한 전자기적인 결합문제를 고려하였다. 결합 슬릿 근처 도파관 내 $.$외부의 무효전력을 반영한 슬릿의 등가 어드미턴스를 구하고, 슬릿의 폭이 매우 좁은 경우에서의 최대결합 메커니즘을 규명하였다. 도파관의 높이, 슬릿의 폭 및 슬릿의 변위 등과 같은 구조적인 파라미터들이 복사 특성에 미치는 영향을 관찰하였다.

• 대한전자공학회:학술대회논문집
• /
• 대한전자공학회 2001년도 하계종합학술대회 논문집(5)
• /
• pp.9-12
• /
• 2001

Optical aligning process to archive the maximum optical coupling is crucial in many optical device manufacturing line such as laser diode module. Due to the three-dimensional nature of housing module and the aligning process for laser diode coupler, large amount of the manufacturing time, typically ranging from tens of minutes to an hour has to be devoted to the aligning process alone. In this thesis, we propose a new optical aligning process that employee a two-pass algorithm: coarse-to-fine search. Coarse search is a kind of blind search that finds the candidate region where the maximum optical coupling might mostly occur, followed by a fine searching that finds the maximum within the candidate region. The algorithm has been tested on 50 samples of cam-type laser diode modules, and the experimental results are analyzed in terms of aligning time and coupling efficiency.

• 대한건축학회논문집:구조계
• /
• 제35권10호
• /
• pp.181-190
• /
• 2019

In this study, four reinforced concrete coupling beams were subjected to cyclic lateral loading test to evaluate the structural performance of coupling beam according to volume fraction of steel fiber. For this purpose, the volume fraction of steel fiber(0%, 1%, 2%) and transverse reinforcement spacing were determined as the main parameter. According to the test results, the maximum strength of D-40C-s100-0 was 1.15, 1.13, 1.05 times higher than D-40C-s300-0, D-40C-s300-1, D-40C-s300-2, respectively. The maximum strength of coupling beams with mitigated rebar details increases as the volume fraction of steel fiber increases. Although steel fiber 2% reinforced specimen(D-40C-s300-2) did not satisfy the amount of transverse reinforcement required for seismic design of coupling beam, the overall performance including to maximum strength, ductility and energy dissipation capacity was similar to the control specimen(D-40C-s100-0). As a result, the use of steel fiber with 2% reinforcement can partially replace the transverse reinforcement in diagonally reinforced concrete coupling beam.

• 한국생산제조학회지
• /
• 제22권5호
• /
• pp.774-781
• /
• 2013

A structural analysis was carried out for a 60 N.m class flexible disk coupling. Flexible disk couplings are used to transmit power between two shafts. When a flexible coupling is used, some amount of misalignments such as angle of deviation and end play can be allowed in assembling the shafts. However, the maximum allowable misalignment should be decided to guarantee the fatigue life. In this study, the effect of the angle of deviation and end play on the maximum stress was investigated. From the analysis results, it was shown that the angle of deviation has a greater effect on the maximum stress than the end play. Furthermore, the dimensions of the disk plate were optimized to realize a better design. From the optimization, the maximum stress could be reduced by up to 5.2%.

• Current Optics and Photonics
• /
• 제5권5호
• /
• pp.538-543
• /
• 2021

The evanescent wave coupling of a microring resonator is controlled by changing the gap distance between the bus waveguide and the microring waveguide. However, the interdependence of the bus waveguide's width and the coupling is not well understood. In this paper, we investigate the dependence of coupling strength on the bus waveguide's width. The strength of the evanescent wave coupling is analytically calculated using coupled-mode theory (CMT) and numerically calculated by three-dimensional finite-difference-time-domain (FDTD) simulation. The analytic and numerical simulation results show that the phase-matching condition in evanescent wave coupling does not provide maximum coupling strength, because both phase-matching and mode confinement influence the coupling. The analytic and simulation results for the evanescent coupling correspond to the experimental results. The optimized bus-waveguide width that provides maximum coupling strength results in intrinsic quality factors of up to 1.3 × 10⁶. This study provides reliable guidance for the design of microring resonators, depending on various applications.

• 국제초고층학회논문집
• /
• 제3권2호
• /
• pp.107-120
• /
• 2014

A Reinforced concrete (RC) shear wall system with coupling beams has been known as one of the most promising structural systems for high-rise buildings. However, significantly large flexural and/or shear stress demands induced in the coupling beams require special reinforcement details to avoid their undesirable brittle failure. In order to solve this problem, one of promising candidates is frictional hysteretic energy dissipating devices (HEDDs) as an alternative to the coupling beams. The introduction of frictional HEDDs into a RC shear wall system increases energy dissipation capacity and maintains the frame action after their yielding. This paper investigates the strength demands (specifically yield strength levels) with a maximum allowable ductility of frictional HEDDs based on comparative non-linear time-history analyses of a prototype RC shear wall system with traditional RC coupling beams and frictional HEDDs. Analysis results show that the RC shear wall systems coupled by frictional HEDDs with more than 50% yield strength of the RC coupling beams present better seismic performance compared to the RC shear wall systems with traditional RC coupling beams. This is due to the increased seismic energy dissipation capacity of the frictional HEDD. Also, it is found from the analysis results that the maximum allowable ductility demand of a frictional HEDD should increase as its yield strength decreases.

• Journal of the Optical Society of Korea
• /
• 제20권2호
• /
• pp.291-299
• /
• 2016

We have investigated the ultimate limits of nonuniform grating couplers (NGCs) for optimized fiber coupling to silicon waveguides, compared to uniform grating couplers (UGCs). Simple grating coupler schemes, which can be fabricated in etching steps of the conventional complementary metal-oxide semiconductor (CMOS) process on silicon-on-insulator (SOI) wafers without forming any additional overlay structure, have been simulated numerically and demonstrated experimentally. Optimum values of the grating period, fill factor, and groove number for ultimate coupling efficiency of the NGCs are determined from finite-difference time-domain (FDTD) simulation, and confirmed with experimentally demonstrated devices by comparison to those for the UGCs. Our simulated results indicate that maximum coupling efficiency of NGCs is possible when the minimum pattern size is below 50 nm, but the experimental value for the maximum coupling efficiency is limited by the attainable fabrication tolerance in a practical device process.

• 한국전자파학회논문지
• /
• 제17권6호
• /
• pp.501-510
• /
• 2006

본 논문에서는 플랜지된 평행 평판 도파관의 슬릿을 통한 도체 스트립과의 전자기적인 결합을 연구하였다. 슬릿의 전계와 스트립의 유기 전류에 관한 결합 적미분 방정식을 유도하고 모멘트 방법으로 풀었다. 몇 가지 슬릿을 통한 최대 결합 현상들의 특성을 도체 스트립의 위치, 동작 주파수, 스트립의 길이 등 다양한 파라미터에 대한 슬릿의 등가 어드미턴스와 결합 전력의 변화를 통해 조사하였다.

• 한국안전학회지
• /
• 제18권2호
• /
• pp.119-124
• /
• 2003

Despite rapid technological advance and increased automation facilities, many jobs and activities in our living require manual materials handling(MMH). These include wide variety of activities such as moving things, lifting bags. boxes or cartons, etc. Many studies found that handle could affect on maximum acceptable weight of lifting, but there were few studies f3r the effects of work posture and coupling in lifting tote box. This study performed that ten male college students were required to lift a tote box with and without handle for three postures (bending, straight, right angle posture). From the experiment, following results were obtained. (1) MVC reduced maximum 23% by type of handle. (2) MVC was highest in straight posture, but was lowest in right angle posture. (3) As a result of ANOVA, MVC paid attention to posture and coupling. (p<0.01) (4) To all handle types, biceps brachii activity was increased in right angle posture. but reduced in straight posture. (5) To all posture, biceps brachii activity was most lively in no handle. The results of MVC measurement, subjective rating, EMG analysis, statistic analysis showed that maximum acceptable weight of lifting was influenced by type of handle and straight posture was more comfortable than other postures. Based on these results, it was concluded that acceptable weight of lifting has to differ for work posture and coupling.