• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.14 no.4
• /
• pp.1555-1560
• /
• 2013

The Column type Motor Driven Power Steering(CMDPS) systems are generally equipped among passenger vehicles ensuring better vehicle safety and fuel economy. In general to analyze systems and to develop a controller a full vehicle model from CarSim developed by Mechanical Simulation Incorporation interacting with MDPS control algorithm from Matlab Simulink was concurrently simulated. This paper describes the development of concurrent simulation technique in detail for analyzing Matlab Simulink MDPS control system with a dynamic vehicle system because the specific method has not been revealed in detail. The steering wheel angle input was evaluated and well compared with proving ground experimental data. The comparisons from concurrent simulation show an effective way to develop and validate the control algorithm. This concurrent simulation capability will be efficiently used for CMDPS performance evaluation and logic tuning as well as for vehicle handling performance.

• Journal of Electrical Engineering and Technology
• /
• v.3 no.3
• /
• pp.314-319
• /
• 2008

Power quality simulation plays an important role in many practical cases, for example, when deciding the capacity of the related mitigation devices, assessing the influence of installing a nonlinear load in the distribution part, dissolving the quality issues between utilities and customers, and so on. For these purposes, many dedicated tools have been used in order to assess the level of quality distortions by various kinds of PQ indices. However, there are few modules that can accurately simulate the flicker phenomenon, that is, $P_{st}$ and the nonlinear and chaotic behavior of the electrical arc furnace, which is one of the representative nonlinear loads. This paper deals with the useful and simple modules for the voltage flicker simulation in the distribution and transmission level under the environment of Matlab/Simulink. With these modules, the various conditions of distribution systems and the capacities of arc furnaces with the chaotic characteristic can be easily taken into account.

• The Journal of The Korea Institute of Intelligent Transport Systems
• /
• v.5 no.2 s.10
• /
• pp.11-18
• /
• 2006

In this paper, we present the algorithm for calculating the interference of the received Non-ideal receiver filter and present the method for calculating the interference faster than that of the conventional method. The algorithm is simulated by Matlab and the simulation procedure is described by the flow-chart. The algorithm is verified by comparing the simulated results by Matlab with the result by calculator.

• Proceedings of the KIEE Conference
• /
• 2000.07a
• /
• pp.449-451
• /
• 2000

Arcing fault on overhead lines can be detected by amplitude of the arc voltage using numerical algorithm. In the case of transient fault, the arc voltage has any high value. In the case of permanent fault, the arc voltage is near zero. Thus, fault distance estimation should be performed by digital distance relay algorithm[3]. The purpose of this study is to build a structure for modeling of arcing fault detection and fault distance estimation algorithm using Matlab programming. Additionally, this algorithm has been designed in Graphical User Interface(GHI). So, this method using GUI interface of Matlab can reduce the number of simulation steps in modeling the distance relay.

• Proceedings of the KIEE Conference
• /
• 2002.11d
• /
• pp.191-193
• /
• 2002

최근, 전기품질에 관한 중요성과 EMI에 의한 규정이 강화되면서 PFC 컨버터에 관한 연구가 많이 이루어지고 있다. 본 연구에서는 matlab을 활용하여 3상 PFC 컨버터를 효율적으로 시뮬레이션하는 연구를 수행한다. 단위역률을 위한 3상 컨버터 PFC 제어는 링크전압제어부, 전류제어부, SVPWM 제어부로 구성된다. 3상 PFC 컨버터를 matlab/simulink로 구성하여 시뮬레이션을 수행한 결과. 상전압과 상전류의 위상이 일치하여 단위역률이 잘 실현됨을 나타내고 있다. 본 연구는 PFC 컨버터의 설계 및 유사회로의 시뮬레이션에 유용하게 활용될 것이다.

• Journal of Institute of Control, Robotics and Systems
• /
• v.16 no.7
• /
• pp.655-660
• /
• 2010

As increasing the number of Electronic Control Units in a vehicle, the proportion for reliability and stability of the software is going increasingly. Accordingly, the traditional CAN network has occurred the situation that the requirement of developing vehicle software is not sufficient. To solve these problems, the FlexRay network which is ensured the high bandwidth and real-time is generated. However it is difficult to implement FlexRay based application software because of complex protocol than traditional CAN network. Accordingly the system for analysis and verification of network state is needed. Also vehicle vendor develops application software using Matlab/Simulink in order to increase productivity. But this development method is hard to solve the network problem of node to node. Therefore this paper implements Matlab/Simulink based FlexRay network system and verifies it through comparing with existing embedded system.

• Proceedings of the KIEE Conference
• /
• 2003.07d
• /
• pp.2630-2632
• /
• 2003

본 연구는 철도 선로변에 설치되는 LDTS(Local Data Transmission System)와 EIS(Electronic Interlocking System) 사이의 인터페이스를 위한 정보전송 프로토콜에 대한 성능검증 시뮬레이션을 위한 것으로, LDTS와 EIS사이의 링크사양, 전송 메시지 정보 및 형식, 장치간 전송 프로토콜 기준 등을 분석하여 파라미터들을 추출한 후, 이들을 ARQ, FEC, HARQ 방식들에 적용하여 처리율(Throughput) 및 여러 설계변수들에 대한 시뮬레이션 결과를 비교하였다. 시뮬레이션 프로그램은 Matlab과 Matlab GUI 툴을 이용하여 작성하여 사용자가 손쉽게 시뮬레이션 파라미터들을 조정할 수 있도록 하였고, Matlab 프로그램 완성후에는 이를 Stand-alone C++ 프로그램으로 코드변환하여 Matlab이 설치되지 않은 컴퓨터에서도 프로그램 사용이 가능하도록 하였다.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.57 no.8
• /
• pp.1383-1391
• /
• 2008

This paper presents an implementation of vector control for SPMSM using model based controller design in MATLAB/SIMULINK. The model based controller design enables fast development of control system for motor by designing controllers and performing simulation on the GUI (Graphic User Interface) platform, converting program code directly into real-time programs, and then performing tests for the responses from controllers. The controllers designed in this paper are PI speed controller and decoupling PI current controller. Also space vector modulation method using offset voltage is used in PWM scheme. And system stability is also secured by close magnitude overmodulation method, maintaining dynamics of load when overmodulation occurs. The validity of vector control implemented is verified through simulations and experiments.

• Proceedings of the KIEE Conference
• /
• 2007.07a
• /
• pp.1954-1955
• /
• 2007

This paper presents a modeling method of speed controller for DC motor drive system by using the Embedded Target for TI C2000 DSP in MATLAB/SIMULINK. Speed controller is easily designed and implemented by using the MATLAB/SIMULINK program, and speed control response and stability of the DC motor can be improved. Feedback of motor speed is processed through C28x QEP(Quadrature Encoder Pulse) from encoder pulse. The controller is designed as PI speed controller. Simulation program is drawn using SIMULINK. Then a real-time program for speed control of the DC motor is downloaded into the eZdsp F2811 control board. Speed control response is verified through simulations and experiments.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.22 no.8
• /
• pp.18-25
• /
• 2008

The paper presents a modeling of the grid-connected wind turbine generation system on MATLAB/Simulink and aims to perform simulations for analysis of the system's characteristics. It performs a pitch regulation for control of the wind generator's output with respect to wind speed variation, and presents a relationship between interconnecting transformer's connections and fault current by reviewing the variations of fault current according to transformer connections in a grid-connected wind power generation system. It also investigates the effect of grounding methods of the interconnecting transformer's neutral point on fault current variations. The simulation results show the differences of fault currents, voltages and generator's characteristics for a line-to-ground fault according to interconnecting transformer's four different connections, and the differences of fault currents of the system according to grounding methods of the transformer neutral point. Therefore, the case studies demonstrate the effectiveness of the proposed simulation model on Simulink.