• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.22 no.1
• /
• pp.74-80
• /
• 2021

This study investigated the process quality level of a K5 gas mask, which recently acquired its operational capability, through statistical process analysis for the mass production stages and their lots. The tensile adhesion strength was the only operating requirement in the manufacturing process of the K5 gas mask. For this purpose, the results of tensile adhesion strength between the lens and facial rubber during the initial and second mass production stages were analyzed using conventional statistical and statistical process analysis methods. The conventional statistical results indicated that the second mass production stage was better than the initial mass production stage. In cases of a control chart and process capability of tensile adhesion strength, the process quality level was also improved by following the mass production stages. The improvement was caused by process stabilization and work skill elevation. These results and methods are expected to be conducted and utilized in the third mass production stage. Moreover, quality improvement of K5 gas mask mass production can be achieved using the Lean 6 sigma procedure, MDAIC (Define, Measure, Analyze, Improve, Control).

• Journal of the Korean Society of Food Culture
• /
• v.35 no.3
• /
• pp.285-293
• /
• 2020

This study was conducted to monitor the residual pesticides on red pepper powder produced in five regions, which are the major producers of red pepper in Korea, such as Ham-pyeong, An-dong, Yeong-yang, Yeong-gwang, and Cheongyang from 2015 to 2016. Residual pesticides were detected on all samples. Among the 286 pesticides tested, 58 pesticides were detected, with the most frequently detected being chlorfenapyr (93.7%). Twelve types of pesticides (chlorfenapyr, cypermethrin, chlorpyrifos, pyraclostrobin, cyhalothrin, tebuconazole, bifenthrin, deltamethrin, fenvalerate, lufenuron, azoxystrobin, and indoxacarb) were detected in all regions, and 14 types of pesticides were used only in certain regions. An analysis of the residual pesticides showed that none of the pesticides detected exceeded the MRL (Maximum Residue Limits). The Positive List System (PLS) requirements were applied to eight pesticides that had no set MRLs. 0.01 mg/kg (PLS requirements) was exceeded in 12 cases. A comparison of the estimated daily intake (EDI) of pesticides with the acceptable daily intake (ADI) to access their risk revealed %ADI values of 0.001-0.756. Carbofuran showed the highest (0.756%), but most pesticides were below 1%. The results show that residual pesticides in red pepper powder are at safe levels.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.22 no.1
• /
• pp.372-378
• /
• 2021

A body armor vest is a form of munition related directly to the safety and life of combatants. Therefore, it must meet the requirements for ballistic resistance. The ROK demands the performance of body armor vest meet the Level IIIA specified by the NIJ STD-0101.06 published by the US National Institute of Justice. This study performed acceptance tests on body armor vests. The factors for evaluating the ballistic resistance evaluated were not only whether it penetrates when shooting but also whether the BFS (Backface Signature) depth does not exceed 44 mm when it does not penetrate. The factors were assessed to determine if they were consistent or not. The BFS depth is affected by various test factors, such as the physical properties of the backing material and the changes in the amount of impact with the bullet velocity. In this study, an analysis of the bulletproof performance was performed by extracting the data with the same conditions using ANOVA to remove the influence of these external factors. The analysis revealed a correlation between the BFS depth, bullet velocity, vest conditions, and protection area. The mass production process was analyzed by estimating the Interval of BFS on each lot. Through this, a new methodology for ballistic resistance evaluation and paradigm for future quality assurance is suggested.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.22 no.3
• /
• pp.25-32
• /
• 2014

There are many type vehicles in army. They are jeep and truck by basic type. Recently many countries are developing new conceptual military vehicles. And they try for export of those military vehicles to another countries. Also Korea Army is developing military tactical and combat vehicles, and considering various necessary factors for export. But as easing the cold war system tension and reducing of defense budget, decrease in quantity of military vehicles. We think this trend is accelerative. Therefore Government(Military) and defense industry make every effort to increasing sales and productions. In this study, I'll inquire '2013~2017 basic plan for defense industry promotion' for strengthen the power of international competitiveness, and then suggest the increasing method for productions of military vehicles.