• Resources Recycling
• /
• v.19 no.4
• /
• pp.41-50
• /
• 2010

A fundamental study was carried out to develop a process for recycling tungsten and cobalt from WC-Co hardmetal sludge generated in the manufacturing process of hardmetal tools. The complete extraction of cobalt and simultaneous formation of tungstic was achieved by treating the sludge using aqua regia. The effect of aqua regia concentration, reaction temperature and time, pulp density on cobalt leaching and tungstic acid formation was investigated. The complete leaching of cobalt was attained at the optimum conditions: 100 vol.% aqua regia concentration, $100^{\circ}C$ temperature, 60 min. reaction time and 400 g/L pulp density. A complete conversion of tungsten carbide of the sludge to tungstic acid was however, obtained at the pulp densities lower than 150 g/L under the above condition. The progress of reaction during the aqua regia treatment of the sludge was monitored through the XRD phase identification of the residue. The metallic impurities in the tungstic acid so produced could be further removed as insoluble residues by dissolving the tungsten values in ammonia solution. The ammonium paratungstate($(NH_4)_{10}{\cdot}H_2W_{12}O_{42}{\cdot}4H_2O$) of 99.85% purity was prepared from the ammonium polytungstate solution by the evaporation crystallization method.

• Resources Recycling
• /
• v.22 no.1
• /
• pp.64-71
• /
• 2013

Mineral carbonation has been proposed as a possible way for $CO_2$ sequestration. The electric arc furnace slags consist of calcium, magnesium and aluminum silicates in various combinations. If they could be used instead of natural mineral silicates for carbonation, considerable energy savings and $CO_2$ emissions reductions could be achieved. Indirect aqueous carbonation of the slags consists of two steps, extraction of calcium and carbonation. Acetic acid leaching of electric arc furnace slags had been already studied to extract Ca in them, but it was reported that the carbonation of the extracted $Ca^{2+}$ in the leached solution would suffer from too slow kinetics, even at high pressure of $CO_2$. In this work, to develop more efficient extraction of the electric arc furnace slags, hydrochloric acid leaching to separate calcium from them was studied, and the results were compared with the acetic acid ones. The phase boundary between $Ca^{2+}$ and $CaCO_3$ in the solution with pH was determined by thermodynamic calculations. Hydrochloric acid was more effective than acetic acid for the extraction of Ca in electric arc furnace slag, and there is a possibility to recycle an unreacted hydrochloric acid in the leached solution by electrolysis or evaporation.

• Journal of Korean Society of Environmental Engineers
• /
• v.32 no.6
• /
• pp.587-592
• /
• 2010

A numerical analysis of reactive flow in a MILD(Moderate and Intense Low oxygen Dilution) combustor is accomplished to elucidate the characteristics of combustion phenomena in the furnace with the variation of air fuel ratio. For the smaller magnitude of air injection velocity(10 m/s), the air flow could not penetrate toward upper part of furnace. On the other hand, the air flow suppresses the fuel flow for the case of air injection velocity 30 m/s. The air velocity 18 m/s is corresponding to the stoichiometric air flow velocity, and for that case, the air flows to relatively more upper part of the furnace when compared with the case of air injection velocity 10 m/s. The reaction zone is produced with the previous flow pattern, so that the reaction zone of the air injection velocity 10 m/s is biased to the air nozzle side and for the case of air injection velocity 30 m/s, the reaction zone is inclined to the fuel nozzle side. For the cases with the air injection velocities 16, 18, 20 m/s, the reaction zone is nearly located at the center between air nozzle and fuel nozzle. The maximum temperatures and NOx concentrations for the cases of air injection velocity 16, 18, 20 m/s are lower than the cases with air injection velocity 10, 30 m/s. From the present study, the stoichiometric air fuel ratio is considered as the most optimal operating condition for the NOx reduction.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.33 no.2
• /
• pp.173-180
• /
• 2013

Compacted graphite iron(CGI), also known as vermicular graphite iron, is a metal which is gaining popularity in applications that require either greater strength, or lower weight than cast iron. Recently compacted graphite iron has been used for diesel engine blocks. Considering that using in exhaust manifold of the diesel engine, CGI340 was conducted the heat treatment during 1 hour to 96 hours from 873 to 1273 K. Mechanical characteristics were evaluated. The obtained results are as follows; The tensile strength of the heat treated specimens showed overall lower tensile strength than that of the base metal. Tensile strength decreases with increasing of heat treatment time, and the higher heat treatment temperature and the longer time, were more reduced. The fatigue limit by the ultrasonic fatigue test was approximately 130 MPa of base metal, 100 MPa of 1173 K (96 hrs) specimen, respectively. The hardness decreases with increasing heat treatment time, and the higher the heat treatment temperature was lowered hardness distribution. In CGI340, average hardness of nodular graphite was 120 Hv, average hardness of vermicular graphite was 114 Hv. This showed lower hardness than the base structure ferrite. The nodular graphite and vermicular graphite according to the heat treatment temperature and time didn't have a consistent change. However, the grain size of base structure grew with increasing of heat treatment time.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.14 no.6
• /
• pp.2596-2603
• /
• 2013

The precision and endurance of tire mold are very important factors to decide the quality of tire. However, the investigation on the thermal deformation of tire mold has a lot of trouble because the tire mold is produced in airtight permanent casting material. In this study, the thermal deformations such as temperature, displacement and stress distributions inside the AC7A tire mold casting material were analyzed by numerical analysis according to the preheating temperature of permanent casting device. In order to verify the results of numerical analysis, the experiments for temperature measurement of the AC7A casting material were carried out under the same condition with numerical analysis. For the numerical analysis, "COMSOL Multiphysics" was used. The preheating temperatures were set up $150^{\circ}C$, $200^{\circ}C$, $250^{\circ}C$ and $300^{\circ}C$, respectively. The thermal deformations were calculated in each case. When the preheating temperature is $300^{\circ}C$, displacement and stress are the lowest with 0.25mm and 0.351GPa, but the temperature is the highest with $374.27^{\circ}C$. When the experimental results were compared with the numerical results, there were some temperature differences because of the latent heat by phase change heat transfer. However, the cooling patterns were almost similar except for the latent heat section.

• Journal of the Korean Magnetics Society
• /
• v.16 no.1
• /
• pp.45-50
• /
• 2006

Oxygen-deficient anatase and rutile titanium dioxide $(TiO_{2-\delta})$ thin films were prepared by a sol-gel method and their structural, electronic, and magnetic properties were investigated. Both anatase and rutile $TiO_{2-\delta}:Fe$ Fe films exhibited ferromagnetism at room temperature for a limited range of Fe doping. For the same amount of Fe doping, the anatase sample exhibited a higher magnetic moment than the rutile one. Result of conversion electron Mossbauer spectroscopy measurements indicates that $Fe^{3+}$ ions substituting the octahedral $Ti^{4+}$ sites mainly contribute to the room-temperature ferromagnetism. Some of the anatase $TiO_{2-\delta}:Fe$ films exhibited p-type character but the observed feromagnetism turns out to be independent of the hole concentration. The room-temperature ferromagnetism can be explained in terms of a direct ferromagnetic coupling between two neighboring $Fe^{3+}$ ions via an electron trapped in oxygen vacancy in $TiO_{2-\delta}:Fe$.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.14 no.1
• /
• pp.11-18
• /
• 2019

This paper explores desirable status of block chain electronic government in relation to the prevention of cybercrimes and corruption. After the research, we suggest four measures to establish desirable status of block chain electronic government. Eventually, transparency is ensured thanks to the core concept of block chain technology, sharing, not only allowing all of the participants to share information and but also preventing them from forging or falsifying information. Furthermore, a wide variety of participants can play a role as monitors in the horizontal structure of governance system, which also assures credibility and reliability on electronic government through trust on block chain itself. Electronic government aims at virtue of expanded electronic democracy which strengthens information democracy. Also, establishment of electronic governance, that emphasizes networking and guarantees, is a desirable image of the future of the fourth industrial revolution. Therefore, the establishment of future electronic government according to the four principles drawn from this paper can be the most suitable model.

• Nuclear Engineering and Technology
• /
• v.18 no.3
• /
• pp.218-227
• /
• 1986

Studies were conducted to determine the extent of oxidation and same of the mechanical property changes of Zircaloy-4 fuel cladding after it was exposed to hot steam environment. The purpose of these tests was to provide some informations on the embrittlement behavior of CANDU type fuel cladding, which could be experienced under the loss-of-coolant accident conditions. The Zircaloy fuel cladding tubes were exposed in a steam environment at the temperature of 90$0^{\circ}C$, 1,00$0^{\circ}C$. The growth of the ZrO$_2$ layer combined with an oxygen rich $\alpha$-phase layer into the Zircaloy tube material was found as a function of time t and temperature of steam exposure, E=1.1√Dt+0.002 where D is a temperature dependent diffusion coefficient. The tensile strength of the specimens exposed for a short period increased but decreased continuously with further exposure. The circumferential elongation was drastically changed with the exposure time while the hoop strength did't decrease greatly. The X-ray measurement of preferred orientation of the Zircaloy tube material indicated that grains in the as received tube were oriented such that the poles of the basal (0001) planes were predominantly radial, while the poles of the basal plane in the tube materials heattreated at 1,00$0^{\circ}C$ were oriented tangentially. It appears that this reoriented texture may contribute to lessening the decrease of the hoop strength of the heat treated Zircaloy tube material.

• Journal of the Society of Cosmetic Scientists of Korea
• /
• v.37 no.4
• /
• pp.337-345
• /
• 2011

In this report, we have investigated the functional properties change of phytochemicals by the encapsulation using water soluble host, ${\beta}$-cyclodextrin. The cream, shampoo, bodywash, and hair tonic containing phytochemical supramolecules were produced by mixing the surfactants, fragrances and the oriental herbal extracts encapsulated with ${\beta}$-cyclodextrin. Shampoo and bodywash including the encapsulated phytochemicals exhibited anti-growth activity against Gram (+) and Malassezia furfur which is known to cause dandruff. In cytotoxicity test against HDF (human dermal fibroblast), we could not detect any toxicity when the supramolecules content was less than 1 mg/mL. Our results suggest that the supramolecule of ${\beta}$-cyclodextrin with phytochemicals could be a safe anti-bacterial agent for cosmeceuticals.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.11 no.12
• /
• pp.5216-5220
• /
• 2010

Rheological measurement of a thermotropic liquid crystalline poymer (TLCP) is not an easy task since their rheological responses are strongly influenced by a thermal history during a processing and thus the reproducibility of the measurement is poor. In order to find out a cause for the strong influence of the thermal history, rheological measurements and DSC observations of the TLCP having various thermal histories were carried out. It was observed that the TLCP used in this study shows liquid-like behavior at a temperature above a crystal-nematic transition temperature ($280^{\circ}C$), but at the same time crystallization can occur at this temperature range and as a consequence the viscosity of the polymer continuously increases. When the samples are heated beyond the $320^{\circ}C$, all crystals thus formed and the thermal histories were observed to disappear. Crystallization rate of the samples annealed above $320^{\circ}C$ was very low at even the lowed temperature ($280^{\circ}C\;{\sim}\;320^{\circ}C$). Therefore, it is concluded that rheological measurements of TLCP used in this study must be performed after annealed above the nematic-isotropic transition temperature for better reproducibility.