• Korean Journal of Materials Research
• /
• v.8 no.4
• /
• pp.354-358
• /
• 1998

Effect of cold drawing ratio and aging time on the hardness of lnconel 718 wire aged at 11l6K were investi¬gated by hardness measurement and scanning & transmission electron microscopy. Hardness which was 245Hv in as¬solution treated condition increased very rapidly to 450Hv as cold drawing ratio increased to 50%. The hardness in the early stage of aging was increased by the precipitation of $\gamma^{'}$ and $\gamma^{'}$ phases and after the peak hardness, the hardness was decreased by the transformation of $\gamma^{'}$ phase to $\delta$ phase. The time to reach peak hardness during aging appeared to be reduced with the increase of cold drawing ratio, and those times were 30, 10, and 5 minutes for 0, 30 and 50% cold drawn materials, respectively. For the 50% cold drawn material. $\gamma^{'}$ and $\gamma^{'}$ were precipitated by aging for 5 minutes at 1116K. The hardness in the same material was largely decreased under the initial hardness by the recrystallization.

• Korean Journal of Metals and Materials
• /
• v.49 no.2
• /
• pp.121-127
• /
• 2011

The mechanical properties of the various heat treatment conditions on Ti-15Mo-3Nb-3Al-0.2Si alloy plates were examined. XRD patterns from the surface of Ti-15Mo-3Nb-3Al-0.2Si were analyzed as a solution-treated Ti alloy has the single-phase ${\beta}$ structure whereas the aged Ti alloys have the ${\beta}$ matrix embedded with ${\alpha}$ needles. High strength (~1500 MPa) with decent ductility (7%) was obtained by the Ti alloy double aged at $300^{\circ}C$ and $520^{\circ}C$ for 8 hours each. The double-aged alloy exhibits the finer structure than the single-aged alloy at $300^{\circ}C$ for 8 hours because of the higher nucleation rate of ${\alpha}$ needles at an initial low aging temperature ($320^{\circ}C$). TEM observation revealed that the fine nanostructure with ${\alpha}$ needles in the ${\beta}$ matrix ensured the excellent mechanical properties in the double aged Ti-15Mo-3Nb-3Al-0.2Si alloy. In the solution treated alloy, the yield drop, stress-serrations and the ductility minimum typically associated with dynamic strain aging can be attributed to the dynamic interaction between dislocations and oxygen atoms. The yield drop and the stress serration were not observed in aged samples because the geometrically introduced dislocations due to phase precipitates suppressed the dynamic strain aging.

• Transactions of Materials Processing
• /
• v.5 no.4
• /
• pp.327-336
• /
• 1996

The effect of dynamic strain aging on high temperature deformation behaviour of the A-Mg alloy was investigated by strain rate change tests and stress relaxation tests between 20$0^{\circ}C$and 50$0^{\circ}C$. Yield point, short stress transient and periodic discontinuities on the stress-strain curve were considered as an evidence of the effect of dynamic strain aging. With this criterion two distinct strain rate-temperature regimes could be manifested. Dynamic strain aging was considered to be effective in the high temperature-low strain rate regime, whereas dynamic recovery was a dominant deformation mechanism in the low temperature-high strain rate regime. It was found that dynamic strain aging in the high temperature deformation was governed by the mechcanism of diffusion-controlled, viscous dislocation movement.

• Journal of the Korean Society for Heat Treatment
• /
• v.14 no.6
• /
• pp.323-329
• /
• 2001

Artificial aging was performed to simulate the microstructural degradation in 2.25CrMo steel arising from long time exposure at $540^{\circ}C$. The carbide morphologies were classified as acicular, pipe and globular type, and the number of carbides per unit area was measured for each type of carbides. The fine acicular carbides were found to diminish drastically in the initial stage of aging. An attempt was made to evaluate the microstructural degradation in artificially aging heat treated 2.25CrMo steel by the magnetic property measurements such as saturation magnetization, coercivity and remanence. The saturation magnetization showed no distinct trend with aging time. However, the coercivity and remanence were observed to decrease rapidly in initial 920 hours of aging time and then decrease slowly afterwards.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.13 no.10
• /
• pp.847-858
• /
• 2000

The aging characteristics of 2 kinds of 3 years field-aged distribution polymer insulators which were dismounted from 5 regions have been investigated by electrical test and material characterization. Although the tan $\delta$of specimens prepared from weathershed was increased with surface aging, the tan $\delta$and leakage current of real products had no difference between virgin and dismounted ones. Due to the aging, all dismounted polymer insulators had micro-cracks on the surface of weathershed and only the products of manufacturer B showed the reduction of OIT(oxidation induction time). But, there were no differences between virgin and dismounted products in contact angle and chemical structure. Therefore, it can be considered that the aging is only limited on the surface of dismounted polymer insulators and that NMR technique are very useful to evaluate the aging of polymer materials.

• Bulletin of the Korean Chemical Society
• /
• v.21 no.6
• /
• pp.628-634
• /
• 2000

Crosslink is the most important chemistry in a rubber vulcanizate. Degree and type of crosslinks of the vulcanizate determine its physical properties. Change of crosslink density and deformation of a rubber vulcanizate by thermal aging were studied using natural rubber (NR) vulcanizates with various cure systems (conventional, semi-EV, and EV) and different cure times (under-, optimum-, and overture). All the NR vulcanizates were deformed by the thermal aging at 60-100 $^{\circ}C.$ The higher the aging temperature is, the more degree of the deformation is. The undercured NR vulcanizates after the thermal aging were deformed more than the optimumand overcured ones. The NR vulcanizates with the EV cure system were less deformed than those with the conventional and semi-EV cure systems. The deformation of the NR vulcanizates was found to be due to change of the crosslink density of the vulcanizates. The crosslink densities of all the vulcanizates after the extraction of organic materials were also changed by the thermal ging. The sources to change the crosslink densities of the vulcanizates by the thermal aging were found to be dissociation of the existing sulfur crosslink and the formation of new crosslinks by free sulfur, reaction products of curing agents, and pendent sulfide groups.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 1994.11a
• /
• pp.155-155
• /
• 1994

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2003.03a
• /
• pp.146-146
• /
• 2003

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2003.03a
• /
• pp.145-145
• /
• 2003

• Proceedings of the Materials Research Society of Korea Conference
• /
• 1996.11a
• /
• pp.121-121
• /
• 1996