• Tribology and Lubricants
• /
• v.39 no.6
• /
• pp.256-261
• /
• 2023

This study is conducted to evaluate the durability of superhydrophobic surfaces, with a focus on two aspects: contact angle measurement and self-cleaning-performance analysis. Superhydrophobic copper and aluminum surfaces are fabricated using the immersion method and subjected to a rolling wear test, in which a 2 kg weight is placed on a rolling tester, under loaded conditions. To evaluate their durability, the contact angles of the specimens are measured for each cycle. In addition, the surface deformation of the specimens before and after the test is analyzed through SEM imaging and EDS mapping. The degradation of the self-cleaning performance is evaluated before and after the wear test. The results show that superhydrophobic aluminum is approximately 4.5 times more durable than superhydrophobic copper; the copper and aluminum specimens could endure 21,000 and 4,300 cycles of wear, respectively. The results of the self-cleaning test demonstrate that superhydrophobic aluminum is superior to superhydrophobic copper. After the wear test, the self-cleaning rates of the copper and aluminum specimens decrease to 72.7% and 83.4%, respectively. The relatively minor decrease in the self-cleaning rate of the aluminum specimen, despite the large number of wear cycles, confirms that the superhydrophobic aluminum specimen is more durable than its copper counterpart. This study is expected to aid in evaluating the durability of superhydrophobic surfaces in the future owing to the advantage of performing wear tests on superhydrophobic surfaces without damaging the surface coating.

• Journal of Korea Foundry Society
• /
• v.31 no.5
• /
• pp.262-266
• /
• 2011

The aim of this study is to investigate aging behavior of A356 alloy for turbo charger part. The specimen was fabricated by investment casting. Solution heat treatment was performed at $525^{\circ}C$ for 8h and followed by aging treated at $160^{\circ}C$, $170^{\circ}C$ for 0.5~20h. And their microstructures and mechanical properties of the aged specimens were analyzed by scanning electron microscope and hardness tester, respectively. All the cast A356 alloy included eutectic Si particles. In the cast A356 alloy, eutectic Si phase mainly was formed along Chinese script phase. Vickers hardness of the cast was improved by aging treatment due to formation of ${\beta}$" phase and ${\beta}$' phase.

• Tribology and Lubricants
• /
• v.16 no.5
• /
• pp.365-372
• /
• 2000

Tribological behavior of novolac resin-based friction materials with three different relative amounts of graphite and zirconium silicate was investigated by using a pad-on-disk type friction tester. The goal of this paper is to examine the effects of the relative amount of a lubricant and an abrasive in the automotive friction material on friction and wear characteristics at elevated temperature. Friction and wear of friction materials were affected by the existence of transfer film(3$\^$rd/ body layer) at friction interface and the composition of friction material, especially lubricant amount. The friction material with higher content of graphite indicated homogenized and durable transfer film, and resulted in stable friction coefficient regardless of the increase in friction heat. The experimental result also showed that the higher concentration of ZrSiO$_4$ in friction material aggravated friction stability and wear resistance due to the higher friction heat generated at fiction interface during high temperature friction test.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.20 no.1
• /
• pp.42-47
• /
• 2021

Recently, many structures using lightweight materials have been developed. This study was conducted by using Al6061-T6 and carbon fiber reinforced plastic (CFRP), two common lightweight materials. In addition, the failure characteristics of an interface bonded between a single material and a heterogeneous bonding material were analyzed. The specimens bonded with CFRP and Al6061-T6 were utilized by the combination of the heterogeneous bonding material. The specimens had a double cantilevered shape and the bonding between the materials was achieved by applying a structural adhesive. The experiments were conducted in opening mode: the lower part of the samples was fixed, while their upper part was subjected to a forced displacement of 3 mm/min by using a tensile tester. Under the tested amount of strength, energy release rate, and considering the specimens' fracture characteristics in opening mode, the specimen "CFRP-Al" presented the maximum stress, followed by "Al" and "CFRP". We can hence conclude that the inhomogeneous material "CFRP-Al" is useful for the construction of lightweight structures bonded with structural adhesive.

• Transactions of the Society of Information Storage Systems
• /
• v.3 no.3
• /
• pp.129-134
• /
• 2007

Boron nitride (BN) is a highly attractive material for wear resistant applications of mechanical components. BN is super hard and it is the second hardest of all known materials. It also has a high thermal stability, high abrasive wear resistance, and in contrast to diamond, BN does not react with ferrous materials. The motivation of this work is to investigate the tribological properties of BN for potential applications in ultra-precision components for data storage, printing, and other precision devices. In this work, the wear characteristics of BN thin films deposited on DLC or Ti buffer layer with silicon substrate using RF-magnetron sputtering technique were analyzed. Wear tests were conducted by using a pin-on-disk type tester and the wear tracks were measured with a surface profiler. Experimental results showed that wear characteristics were dependent on the sputtering conditions and buffer layer. Particularly, BN coated on DLC layer showed better wear resistant behavior. The range of the wear rates for the BN films tested in this work was about 20 to $100{\mu}m^3$/cycle.

• Journal of the Korean institute of surface engineering
• /
• v.42 no.6
• /
• pp.272-275
• /
• 2009

The purpose of this study is to show the friction and wear characteristic behaviors of TiN and CrN coated SKD61 which is applied to Al 6xxx extrusion mold material. The friction and wear characteristic behaviors of both coating layers were investigated by the reciprocating friction wear tester under atmospheric pressure and un-lubricated state. The processing parameters in this study were temperature (50 and $120^{\circ}C$) and load (3, 5, and 11 kgf). This study was carried out while comparing the coefficient of friction and microstructure of TiN and CrN coating layers on SKD61. The coefficient of friction of CrN became lower than that of TiN at all conditions. Therefore, CrN was suggested to be more advantageous than TiN for extrusion mold.

• Tribology and Lubricants
• /
• v.25 no.5
• /
• pp.330-334
• /
• 2009

Hydraulic servo cylinders have been used to control accurately a large machine in power plant. Especially, Piston head and bush of servo cylinder is assembled sleeve and piston head and bush made of Cu alloy and pad sealing part. A damages of sleeve and piston head, bush are caused by friction and wear. Thus, It is necessary to examine friction and wear characteristics of Cu alloys for the piston head and bush. In this study, to be reliable on the piston and cylinder parts, dry friction and wear experiments were carried out with Cu alloys of four kinds of AlBC, PBC, BC and BS using reciprocating friction tester of pin on disk type. From this study, the result was shown that the AlBC and PBC with alloy elements were excellent to resistance wear. As the sliding speed was increased, the wear loss of PBC decreased than another Cu alloy.

• Proceedings of the KWS Conference
• /
• 2002.10a
• /
• pp.139-144
• /
• 2002

Ti-50.9at%Ni wires were welded using pulsed YAG laser. The laser welded wires were tested for investigating the shape memo교 effect and the ability of super elasticity. The fatigue properties of the welded wires were investigated using the rotary bending fatigue tester specially designed for wires. Moreover, the effect of defocusing distance during laser welding on the static and fatigue properties was investigated. The shape memory effect and super elasticity of the laser welded wires were approximately identical with that of base metal at the test temperature below 353K. However, the welded wires were broken within elastic limit at the test temperature above 353k. Under the cyclic bending loading conditions, the welded wires could be useful only below the elastic limit, while the base metal had sufficient fatigue life even the stress induced M-phase region. The fatigue strength of the welded wires was about half of that of the base metal. The deterioration of the static and fatigue properties in the welded wires was proven to be from the large difference of the transformation behavior between the base metal and welded part that is caused by vaporization of Ni-content at the welded part during the welding process. The defocusing distance below 3mm acted more largely on lowering the strength of the welded wires than that of 6mm or 8mm.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2009.11a
• /
• pp.443-446
• /
• 2009

In this study, a series of degradation test for structural adhesives was performed to investigate the possibility of replacement of the alternative adhesives to the conventional adhesives. Four types of the adhesives were exposed to combined environmental conditions over 1000 hours at an accelerated aging tester, which can simulate natural weather conditions such temperature, moisture and ultraviolet. Mechanical and chemical properties of the adhesives were evaluated through material testing system and FT/IR spectrometer. According to the results, the conventional adhesives can be replaced by the alternative adhesives because the alternative adhesives were more stable to environmental conditions rather than the conventional adhesives.

• Fire Science and Engineering
• /
• v.25 no.3
• /
• pp.119-124
• /
• 2011

In this study, we measured the smoke density characteristics to find the fire risk of Wood-Plastic composites (WPCs) which are one of spotlighting materials for landscape architecture and residential construction material with the cone calorimeter tester (by ISO 5660-2) and the smoke density tester (by ASTM E 662). In addition, the identical test was implemented to compare the smoke density characteristics between the red pine and the antiseptic wood. The result of cone calorimeter test showed that emissions of carbon monoxide, carbon dioxide and total smoke production rate of WPCs were higher than those of red pine and antiseptic wood. And the result of smoke density test showed that maximum specific optical smoke density(Dm) of WPCs was higher than that of red pine and antiseptic wood as well.