• KSTLE International Journal
• /
• 제2권2호
• /
• pp.150-153
• /
• 2001

The effects of humidity on friction performance of automotive brake materials were studied using a pad-on-disk type friction tester. Three different friction materials based on a simple formulation were investigated by changing the solid lubricant graphite, MoS$_2$, and Sb$_2$S$_3$. Friction materials without solid lubricants were also examined to study the effect of other ingredients in the matrix on humidity. The friction material containing graphite was strongly affected by the humidity showing lower friction coefficient at high humidity level than other conditions. On the other hand, the friction material containing MoS$_2$exhibited higher friction coefficient at initial stage under high humidity level. The friction material without solid lubricant or with Sb$_2$S$_3$ was not affected by humidity conditions. However, the friction material containing barite showed strong speed dependence.

• Tribology and Lubricants
• /
• 제23권6호
• /
• pp.318-322
• /
• 2007

The wear characteristics in supre-A dental material have been investigated. The wear tests were performed by using pin-on-disk wear tester at room temperature. Vickers hardness and fracture toughness measurement of dental materials were preformed. Microscopic observations on worn surfaces of specimens were conducted by SEM. The friction coefficient of supper-A material was investigated according to weight and slinging velocity. The hardness of supper-A material was a half of the enamel of natural teeth.

• Tribology and Lubricants
• /
• 제14권1호
• /
• pp.45-53
• /
• 1998

Friction and wear test for two kinds of Cu-based sintered metallic friction material against cast iron disk was carried out by plate-on-disk type friction and wear tester to investigate the friction and wear characteristics of brake system in severe condition. In this experimental study, the counter specimen was cast iron which is being used generally in brakes of heavy duty equipments. Test friction materials were A type which was manufactured by foreign company and B type by domestic company. Friction coefficient and wear volume were measured and compared with each other. The experiment was performed under room temperature. The worn surface of cast iron disk and friction material were observed by scanning electron microscope. The temperature of surface of disk was measured continuously by the non-contacting thermometer. It was found that A type friction material had stable friction coefficient over the wide range of sliding condition, but B type friction material had unstable friction coefficient and lower value of 0.2 under the severe sliding condition.

• 한국윤활학회:학술대회논문집
• /
• 한국윤활학회 1998년도 제28회 추계학술대회
• /
• pp.323-329
• /
• 1998

The effect of humidity on friction characteristics of friction materials were studied using a pad-on-disk type friction tester. Three different friction materials containing simplified ingredients were investigated by changing the solid lubricant, graphite, MoS$_2$, and $Sb_2S_3$. A friction material without solid lubricant was also examined to study the effect of ingredients in the matrix on humidity. Friction material containing graphite showed lower friction coefficient at high humidity level than other conditions, however, friction material containing MoS$_2$ indicated higher friction coefficient at initial stage under high humidity level. Friction materials without solid lubricant and with $Sb_2S_3$ were little affected by humidity conditions.

• 대한금속재료학회지
• /
• 제50권8호
• /
• pp.563-568
• /
• 2012

The wetting property and reflectivity of Sn-3.5Ag solder which was dip coated on a LED lead frame were investigated. The wettability of molten solder on Cu substrate was evaluated by the wetting balance tester, and surface tension was calculated from maximum withdrawal force and withdrawal time. Temperature of the molten solder in a bath was varied in the range of $250-290^{\circ}C$. With increasing temperature, the surface tension decreased a little. The reflectivity of Sn-3.5Ag coated on a substrate became a little lower than the highest current LED lead frame reflectivity.

• 한국생산제조학회지
• /
• 제8권5호
• /
• pp.102-107
• /
• 1999

In this paper hardened SCM440 material and annealed SCM440 material are for cutting experiments by the cutting con-dition which is chosen respectively by tool three components of cutting force are recorded using multicorder, Then the surface roughness for various force are measured by Roughness Tester. The results of the experiment are summarized as follow. The hardened material cut by ceramic tool(BX20) gives the highest radial component values among the cutting resistance radial components is increased higher for the higher cutting speed even though vertical component and axial component tend to decrease. But when the annealed material was cut increase in cutting speed results in the increase of three component forces. Since ceramic insert tip used the experiment hardly affect Built-up Edge and heat the cutting resistance decrease slightly regardless of the increased of cutting speed. The hardened material has higher three compo-nent force value than the annealed material because the material of high hardness is increased cutting resistance. The low-est cutting forces for hardened material and annealed material are shown in the cutting speed of 60m/min and 180m/min. respectively.

• 한국안전학회지
• /
• 제33권4호
• /
• pp.8-14
• /
• 2018

In the industrial chemical process involving combustible materials, reliable safety data are required for design prevention, protection and mitigation measures. The accurate combustion properties are necessary to safely treatment, transportation and handling of flammable substances. The combustion parameters necessary for process safety are lower flash point, upper flash point, fire point, lower explosion limit(LEL), upper explosion limit(UEL)and autoignition temperature(AIT) etc.. However, the combustion properties suggested in the Material Safety Data Sheet (MSDS) are presented differently according to the literatures. In the chemical industries, tetralin which is widely used as a raw material of intermediate products, coating substances and rubber chemicals was selected. For safe handling of tetralin, the lower and flash point, the fire point, and the AIT were measured. The LEL and UEL of tetralin were calculated using the lower and upper flash point obtained in the experiment. The flash points of tetralin by using the Setaflash and Pensky-Martens closed-cup testers measured $70^{\circ}C$ and $76^{\circ}C$, respectively. The flash points of tetralin using the Tag and Cleveland open cup testers are measured $78^{\circ}C$ and $81^{\circ}C$, respectively. The AIT of the measured tetralin by the ASTM E659 apparatus was measured at $380^{\circ}C$. The LEL and UEL of tetralin measured by Setaflash closed-cup tester at $70^{\circ}C$ and $109^{\circ}C$ were calculated to be 1.02 vol% and 5.03 vol%, respectively. In this study, it was possible to predict the LEL and the UEL by using the lower and upper flash point of tetralin measured by Setasflash closed-cup tester. A new prediction method for the ignition delay time by the ignition temperature has been developed. It is possible to predict the ignition delay time at different ignition temperatures by the proposed model.

• 한국도로학회논문집
• /
• 제7권3호
• /
• pp.1-10
• /
• 2005

본 연구에서는 일반 아스팔트 포장에 비해 설계수명을 2배 이상 증대시켜 보수주기를 증진하고 보수비용 및 사용자 비용을 절감할 수 있는 장수명 아스팔트 포장에 대한 포장가속시험 (APT)을 수행하였다 먼저 본 연구에서 개발된 장수명 포장용 고강성기층 혼합물에 대한 기초적인 물성시험을 수행하였다. 포장의 지지력을 비교하고 피로 및 소성변형에 대한 저항성을 평가하기 위하여 일반 및 고강성 기층으로 구성된 총 4개의 시험단면을 건설하였다. 또한 일반 및 고강성 단면은 각각 얇은 단면과 두꺼운 단면으로 구성되었다. 다양한 교통하중에 대한 아스팔트 기층하단의 인장변형률을 측정하였으며 시험결과 고강성 단면의 인장변형이 일반단면에 비해 적게 발생되는 것을 확인하였다. 기층 단면이 얇은 포장단면에 대한 APT 시험결과 윤하중이 180,000회 재하될 때까지 균열은 발생하지 않았다. 기층단면이 두꺼운 포장에 대해 윤하중 90,000회 재하시 일반단면은 5.3mm, 고강성 단면은 3m의 소성변형이 발생하였다. 본 연구에서 개발된 고강성 혼합물은 소성변형 및 피로균열에 대한 저항성이 우수하기 때문에 장수명 포장용 기층재로서 적합한 것으로 판단된다. 또한 다양한 구조해석 결과 일반 혼합물 대신 고강성 혼합물을 사용할 경우 포장의 하중지지력이 증가하기 때문에 아스팔트층의 단면두께를 최소 5cm 이상 줄일 수 있을 것으로 판단된다.

• 한국윤활학회:학술대회논문집
• /
• 한국윤활학회 1996년도 제23회 춘계학술대회
• /
• pp.99-107
• /
• 1996

Examined in this paper is the effect of B$_{4}$C addition on the frictional characteristics of Cu-Sn based sintered friction material. For the specimens 1%, 2% and 4% of B$_{4}$C were added into the reference material. A pin-on-disk type friction tester was used to measure the friction and wear with respect to the surface temperature and sliding distance. Wear mechanism of each specimen is analyzed in the view point of the oxide film formation. The specimen containing 4% of B$_{4}$C showed stable friction and low wear since the oxide film was sustained up to higher surface temperature ranges.

• 한국공작기계학회:학술대회논문집
• /
• 한국공작기계학회 2003년도 춘계학술대회 논문집
• /
• pp.393-397
• /
• 2003

Recently, rotating elements which use mechanical and electrical systems have been utilized for high speed and accuracy to increase the performance. The most important thing to get a more reliable system is to understand the friction, wear and characteristics which has an effect on various coated surfaces. In this study, the tribologicali characteristics of various soft/hard materials were investigated by using a custom-built pin-on-reciprocator tester From the experimental results, it was found that the friction coefficients of the soft material coated surfaces were lower under various normal loads due to trier self-lubricating ability and material transfer to the counter surface.