• E2M - 전기 전자와 첨단 소재
• /
• 제7권2호
• /
• pp.107-116
• /
• 1994

In the manufacturing of VLSI circuits, variations of device characteristics due to the slight differences in process parameters drastically aggravate the performances of fabricated devices. Therefore, it is very important to establish optimal process conditions in order to minimize deviations of device characteristics. In this paper, we used one-dimensional process simulator, SUPREM-II, and two dimensional device simulator, MINIMOS 4.0 in order to extract optimal process parameter which can minimize changes of the device characteristics caused by process parameter variation in the case of short channel nMOSFET and pMOSFET device. From this simulation, we have derived the dependence relations between process parameters and device characteristics. Here, we have suggested a method to extract process parameters from design trend curve(DTC) obtained by these dependence relations. And we have discussed short channel effects and device limitations by scaling down MOSFET dimensions.

• Architectural research
• /
• 제14권3호
• /
• pp.93-98
• /
• 2012

The objective of the study is to analyze the relative performance of factors affecting indoor air quality in multi-residential buildings in Korea. A study of the factors affecting indoor air quality is essential for establishing indoor air quality management strategies effectively. To observe the indoor air quality response following a modification of a given parameter, a sensitivity analysis was performed. The factors examined for the analysis include; wall/ceiling paper, adhesive for wall/ceiling paper, floor material, adhesive for floor material, and ventilation rate. The Experimental Design which identifies main effects among the design parameters with a few experiments was used to decrease the number of experiments. The simulation for indoor air quality was undertaken using a validated equation. Then, ANOVA(Analysis of Variance) was performed to evaluate the relative importance of each parameter affecting the indoor air quality. The result of the study indicates that the indoor air quality may be influenced most by adhesive for wall/ceiling paper, followed by ventilation rate and adhesive for floor material.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2001년도 하계학술대회 논문집
• /
• pp.243-246
• /
• 2001

Thyristor devices have 3-dimensional complicated structure and were sensitive to temperature characteristics. Therefore, it was difficult to optimize thyristor devices design. We have to consider many design parameter to characterize, and trade-off relations. The important parameters to design thyristor devices are cathode structure, effective line width, cathode-emitter shunt structure, gate structure, doping profile and carrier lifetime. So, we must consider that these design parameters were not acted separately. However, there are many difficulties to determine optimized design parameters by experiment. So, We used specific design software to design thyristor devices, and estimated the thyristor devices characteristics.

• Tribology and Lubricants
• /
• 제20권5호
• /
• pp.259-265
• /
• 2004

The sealing performance of O-rings is affected by working conditions such as applied pressure, operation temperature, pre-compressed ratio and material properties. In this paper, a pressurized and compressed elastomeric bi-polymer O-ring in which is inserted into a rectangular groove is analyzed by non-linear MARC finite element program based on the Taguchi experimental method. O-rings with 9 different profile models are analyzed for design parameters that are related to the diameter ratio between outer diameter and inner one of bi-polymer O-ring, compressive ratio, groove angle and groove depth. The calculated FEM results showed that the affection ratio of design parameter dlD, which may control sealing pressure of O-rings, is the most influential parameter among the groove angle, groove depth and compression ratio.

• Transactions on Electrical and Electronic Materials
• /
• 제12권5호
• /
• pp.204-208
• /
• 2011

In this paper, the design area of a fabricated solar cell has been analyzed with respect to its charge density. The mathematical calculation used for charge-density derivation was obtained from the 2001 version of a MATHCAD program. The parameter range for the calculations was ${\pm}1{\times}10^{17}cm^{-3}$, which is in the normal parameter range for n-type doping impurities ($7.0{\times}10^{17}cm^{-3}$) and also for p-type impurities ($4.0{\times}10^{17}cm^{-3}$). Therefore, it can be said that the fabricated solar-cell design area has a direct effect on charge-density changes.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2002년도 추계학술대회논문집
• /
• pp.599-604
• /
• 2002

Substructures position is considered as design parameter to obtain optimal structural changes to raise its dynamic characteristics. In conventional SDM (structural dynamics modification) method, the layout of modifying substructures position is first fixed and at that condition the structural optimization is performed by using the substructures size and/or material property as design parameters. But in this paper as a design variable substructures global translational and rotational position is treated. For effective structural modification the eigenvalue sensitivity with respect to that design parameter is derived based on measured frequency response function. The optimal structural modification is calculated by combining eigenvalue sensitivities and eigenvalue reanalysis technique iteratively. Numerical examples are presented to the case of beam stiffener optimization to raise the natural frequency of plate.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2004년도 추계학술대회논문집
• /
• pp.666-669
• /
• 2004

Substructures position is considered as design parameter to obtain optimal structural changes to raise its dynamic characteristics. In conventional SDM (structural dynamics modification) method, the layout of modifying substructures position is first fixed and at that condition the structural optimization is performed by using the substructures size and/or material property as design parameters. But in this paper as a design variable substructures global translational and rotational position is treated. For effective structural modification the eigenvalue sensitivity with respect to that design parameter is derived based on measured frequency response function. The optimal structural modification is calculated by combining eigenvalue sensitivities and eigenvalue reanalysis technique iteratively. Numerical examples are presented to the case of beam stiffener optimization to raise the natural frequency of plate.

• 한국지능시스템학회논문지
• /
• 제19권1호
• /
• pp.96-101
• /
• 2009

본 논문에서는 제안된 진화적 알고리즘을 바탕으로 한 비탄성 구성방정식의 파라미터를 결정하기 위한 방법을 제시한다. 이 방법의 장점은 오차를 갖고 있는 측정된 데이터들이나 모델 방정식들이 부정확하더라도 적절한 파라미터들이 결정되어진다는 것이다. 실험설계는 단축하중과 일정 온도조건하의 샤보쉬 재료모델의 파라미터 결정에 적합하였다. 동시에 모델의 파라미터들은 실험데이터들과 제안한 방법에 의한 값들과 일치하였다. 다른 방법들에 의한 값들과 비교해 본 결과, 제안한 방법에 의한 응력-변형률 선도는 실제적인 재료거동에 비해 좋게 나타났다.

• 한국공작기계학회논문집
• /
• 제15권2호
• /
• pp.66-72
• /
• 2006

The old technique of sandblasting which has been used for paint or scale removing, deburring and glass decorating has recently been developed into a powder blasting technique for brittle materials, capable of producing micro structures larger than $100{\mu}m$. In this paper, we studied on the predictive modeling of material removal and surface roughness in powder blasting of glass by design of experiments. The surface characteristics and surface shape of powder blasted glass surface were tested under different blasting parameter. Finally, we proposed a predictive model for powder blasting process, and compared with experimental results.

• 한국전기전자재료학회논문지
• /
• 제22권3호
• /
• pp.257-261
• /
• 2009

In this study, we have researched the optimum design method of the lenticular lens sheet for 3D displays on a TFT-LCD panel, to offer a more stable stereoscopic image, improved 3D quality, and a wider viewing zone. Especially, we have defined the viewing zone width (a parameter denoted as Z) to apply it to the optimum design. The results of this new design method have been compared with the existing design method. As a result, it is revealed that the proposed design method improves the stereoscopic image quality by reducing the black matrix zone width.