• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 1998년도 봄 학술발표회논문집(II)
• /
• pp.433-438
• /
• 1998

Design lateral strength calculated by current seismic design code is prescribed to be much lower than the force level required for a structure to respond elastically during design level earthquake ground motion. Present procedures for calculating seismic design forces are based on the use of elastic spectra reduced by a strength reduction factor known as "response modification factor, R". This factor accounts for the inherent ductility, overstrength, redundancy, and damping of a structural system. This study considers ductility and overstrength of the wall-type structure for investigating R factor. This means that R factor is determined from the product of "ductility-based R factor($R_$\mu$$) and overstrength factor($R_s$). $R_$\mu$$ factor is calibrated to attain the targer ductility ratio (system ductility capacity) and produced in the from of $R_$\mu$$ spectra considering the influence of target ductility, natural period, and hysteretic model. On the other hand, $R_s$ is more difficult to quantify, since it depends on both material and system-dependent uncertain parameters. In this study Rs factor was determined from the result of push-over analysis.-over analysis.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2003년도 춘계학술대회
• /
• pp.734-739
• /
• 2003

Many types of smart materials and control laws are available to actively adjust the structure from various external disturbances. Usually, a certain type of control laws to activate a specific smart material is well established, but the effectiveness of the control scheme is limited by the choice of the smart materials and the responses of the structure. ER fluid is adequate to provide relatively large control force, on the other hand, the PZT patches are suitable to provide small but arbitrary control forces at any point along the structure. It was found that active vibration control mechanism using ER fluid failed to suppress the excitation off the resonant frequency with changed structural characteristics along the frequency response function of the closed loop of the control system. To compensate this additional peak of the closed loop system, PPF control using PZT as an actuator is added to construct a hybrid controller.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 1992년도 추계학술대회논문집; 반도아카데미, 20 Nov. 1992
• /
• pp.55-58
• /
• 1992

일반적으로 기계계 또는 기계요소가 외력을 받아 진동할 때 공진이 문제시 되는 경우가 많다. 이러한 계의 공진 제어에는 주로 댐핑재료(damping material)의 사용이 일반화 되어왔다. 그러나 댐핑재료를 사용한 제어에 있어 서는 계의 특성이나 규모등에 따라 많은 제한요소가 따르는데 특히 구조물 의 규모가 커지거나 복잡해지면, 제어 위치선정에도 어려움이 따르며 그 효 과도 기대하기 어렵다. 다른 방법으로는 기계계의 동적 특성치에 변화를 주 는 것이나, 이를 허용하지 않는 계가 많다. 따라서 이러한 단점들을 보완하 기 위해서 고안된 것이 동흡진기(dynamic absorber)이다. 기존의 선형 동흡 진기[1]는 주공진 부근영역에서 가진되는 계에만 적용이 가능하기 때문에, 흡진기와 기계계의 크기비(ratio)의 결정이 제한적이다. 이런 제한을 극복하 여 비교적 넓은 범위의 가진 주파수에 대해서 최대의 응답을 최소화하기 위 해서는 비선형 동흡진기[5]의 해석이 요구되고 있다. 제어대상의 최적응답을 얻기 위해 흡진기의 크기를 변화시키는 과정을 tuning이라 하는데, 이 과정 을 통해 최적의 감쇠값을 결정할 수 있다. 비선형 흡진기의 장점은 tuning 과정시 비선형 파라미터 변화에 의해 제어가 가능한 영역을 확장할 수 있다. 따라서 본 연구에서는 동흡진기의 tuning 과정시 흡진기의 크기비와 비선형 파라미터비에 따른 효과를 정규모우드를 활용하여 고찰한 후, 최적의 응답을 통해 비선형 동흡진기의 동적 거동을 연구하였다.

• 한국소음진동공학회논문집
• /
• 제24권5호
• /
• pp.390-398
• /
• 2014

Heavy-weight floor impact noise is directly related to the impact source and floor vibration property. Dynamic properties of the standard floating floor that is used in Korea was investigated using accelerance, acceleration energy spectral density(ESD), and structural modal test. In the standard floating floor, natural frequency was decreased by the finishing mortar mass and the damping ratio was increased. Bang-machine force spectrum acting on the concrete slab can be calculated using inverse system analysis. Impact force acting on concrete slab is changed by interaction of finishing mortar and resilient material. The amplitude of the bang-machine force spectrum was amplified in low frequency range(below 100 Hz), and over 100 Hz was decreased. Changed force spectrum influence to the response of structure vibration, so the heavy-weight floor impact noise level was changed.

• 정보저장시스템학회논문집
• /
• 제3권4호
• /
• pp.160-166
• /
• 2007

In this paper, the measured electrical resistance method is proposed to analyze the ramp-tab contact during the load/unload (L/UL) process. Since this method supplies the voltage change due to the resistance change, we can easily and conveniently identify the ramp-tab contact from the acoustic emission (AE) signal. At first, we carefully deposit the conductive material on the surface of the conventional ramp by sputtering method. The ratio frequency (RF) magnetron co-sputtering system is applied to accomplish the deposited double-layers on the ramp surface. One layer is the stainless steel for the conductive layer and the other is the titanium layer for the cohesive function between the ramp surface and the stainless steel layer. In order to guarantee the stiffness and damping properties of the original ramp, the deposited conductive layer is intended to have very thin thickness. After integration the proposed ramp device into the L/UL system and networking the electrical resistance circuit, the L/UL performance is experimentally evaluated by comparing the measured electrical resistance signal and AE signal.

• Structural Engineering and Mechanics
• /
• 제71권5호
• /
• pp.485-502
• /
• 2019

In this research, the nonlinear static, buckling and vibration analysis of viscoelastic micro-composite beam reinforced by various distributions of boron nitrid nanotube (BNNT) with initial geometrical imperfection by modified strain gradient theory (MSGT) using finite element method (FEM) are presented. The various distributions of BNNT are considered as UD, FG-V and FG-X and also, the extended rule of mixture is used to estimate the properties of micro-composite beam. The components of stress are dependent to mechanical, electrical and thermal terms and calculated using piezoelasticity theory. Then, the kinematic equations of micro-composite beam using the displacement fields are obtained. The governing equations of motion are derived using energy method and Hamilton's principle based on MSGT. Then, using FEM, these equations are solved. Finally the effects of different parameters such as initial geometrical imperfection, various distributions of nanotube, damping coefficient, piezoelectric constant, slenderness ratio, Winkler spring constant, Pasternak shear constant, various boundary conditions and three material length scale parameters on the behavior of nonlinear static, buckling and vibration of micro-composite beam are investigated. The results indicate that with an increase in the geometrical imperfection parameter, the stiffness of micro-composite beam increases and thus the non-dimensional nonlinear frequency of the micro structure reduces gradually.

• Tribology and Lubricants
• /
• 제39권2호
• /
• pp.61-71
• /
• 2023

This study proposes a procedure for designing a labyrinth seal that meets both leakage flow rate and rotordynamic performance criteria (effective damping, amplification factor, separation margin, logarithmic decrement, and vibration amplitude). The seal is modeled using a one control volume (1CV) bulk flow approach to predict the leakage flow rate and rotordynamic coefficients. The rotating shaft is modeled with the finite element (FE) method and is assumed to be supported by two linearized bearings. Geometry, material and operating conditions of the rotating shaft, and the supporting characteristics of the bearings were fixed. A single labyrinth seal is placed at the center of the rotor, and the linearized dynamic coefficients predicted by the seal numerical model are inserted as linear springs and dampers at the seal position. Seal designs that satisfy both leakage and rotordynamic performance are searched by modifying five seal design parameters using the multi-grid method. The five design parameters include pre-swirl ratio, number of teeth, tooth pitch, tooth height and tooth tip width. In total, 12500 seal models are examined and the optimal seal design is selected. Finally, normalization was performed to select the optimal labyrinth seal designs that satisfy the system performance requirements.

• Composites Research
• /
• 제35권3호
• /
• pp.134-138
• /
• 2022

본 연구에서는 기존 폴리머 콘크리트의 진동 감쇠 효과를 향상시키기 위해 압전 재료 중 하나인 PZT 파우더를 첨가하여 티타늄 파우더/폴리머 콘크리트 복합재료를 제작하였다. 티타늄 파우더는 압전 효과를 이용한 진동특성 변화를 극대화하기 위해 일정한 비율로 유지하였고, PZT 파우더를 첨가하지 않은 시편, PZT 파우더를 2.5 wt%, 5 wt% 첨가한 세 가지 종류의 복합재료 시편을 제작하였으며, 모든 시편에 대해 진동 특성 및 압축 물성 분석을 진행하였다. 그 결과, PZT 파우더 첨가 비율이 높아질수록 티타늄 파우더/폴리머 콘크리트에서 발생한 진동이 전달될 때 압전 효과로 인해 공진주파수에서 전달 함수 Inertance 값이 작아지는 것을 확인하였고, 특히 PZT 파우더 5 wt% 첨가 시편의 경우, 공진주파수에서 Inertance 값은 PZT가 첨가되지 않은 시편에 비해 약 19.3% 감소하는 것으로 나타났다. 시간에 따른 가속도 변화 폭 역시 PZT 파우더가 첨가됨에 따라 크게 감소하는 것으로 나타나 PZT 첨가에 따른 효과를 확인할 수 있었다. 또한, 압축강도 시험을 통해 5 wt%까지의 PZT 첨가에 의한 압축 물성 저하 정도는 미미한 것으로 나타났고, 시편 단면 분석을 통해 파우더가 고르게 분산된 것을 확인하였다.

• Structural Engineering and Mechanics
• /
• 제64권3호
• /
• pp.361-379
• /
• 2017

In this article, the vibration behavior of double-bonded sandwich microplates with homogeneous core and nanocomposite facesheets reinforced by carbon nanotube and boron nitride nanotube under multi physical fields such as 2D magnetic and electric fields is investigated. Symmetric and un-symmetric distributions of nanotubes are considered for facesheets of sandwich microplates such as uniform distribution and various functionally graded distributions. The double-bonded sandwich microplates rest on visco-Pasternak foundation. Material properties of sandwich microplates are obtained by the extended rule of mixture. The sinusoidal shear deformation theory (SSDT) is employed to describe displacement fields of sandwich microplates. Also, the dimensionless natural frequency is obtained by classical plate theory (CPT) and compared with the obtained results by SSDT. It can be seen that the obtained dimensionless natural frequencies by CPT are higher than SSDT. In order to study the material length scale parameters, modified strain gradient theory at micro scale is utilized and then, the equations of motion are derived using Hamilton's principle. The effects of different parameters such as foundation parameters including Winkler, shear layer and damping coefficients, various distributions and volume fraction of nanotubes, core to facesheet thickness ratio, aspect and side ratios on the dimensionless natural frequencies are discussed in details. The results of present work can be used to optimum design and control of similar systems such as micro-electro-mechanical and nano-electro-mechanical devices.

• 한국구조물진단유지관리공학회 논문집
• /
• 제20권4호
• /
• pp.94-103
• /
• 2016

궤도가 역사의 상부에 위치하여 열차운행으로 인하여 발생한 진동이 직접 전달되는 선하역사에서 구조물 진동과 이로 인한 구조물기인 소음이 기준치보다 높은 것으로 나타남에 따라, 기존 선하역사에 대하여 열차 운행의 중단 없이 진동저감이 가능한 경제적, 효율적 방안이 요구된다. 이에 본 연구에서는 진동전달 경로상의 기둥에 워터젯 공법으로 기둥단면에서 피복재 부분을 파쇄한 후 진동전달 절연기능을 가지는 에폭시 소재의 방진재를 보강하여 진동을 저감시키기 위한 구조진동절연시스템을 개발하였다. 방진재의 보강체적을 변수로 한 진동절연 시스템을 실제역사 기둥의 1/4축소모형에 적용하고, 충격가진 시험을 통한 진동저감 성능과 횡하중 반복가력시험을 통한 구조적 성능을 검증하고자 하였다. 충격가진 실험결과로부터 구조진동절연시스템을 적용할 경우 고유 진동주기가 하향되어 진동응답 특성이 변화되고 감쇠비는 약 15~30%까지 증가를 나타내어 진동저감 성능이 있음을 알 수 있었다. 또한 반복하중 가력에 의한 구조성능 실험에서 하중-변위 및 강성변화에 대한 고찰과 연성도 및 에너지 소산의 증가를 보인 결과로 부터 구조부재로의 기능을 유지함을 확인 할 수 있었다.