• Proceedings of the Korea Concrete Institute Conference
• /
• 2003.11a
• /
• pp.433-436
• /
• 2003

This paper proposes rheological creep and shrinkage model of FCM bridges made for HPC about 40Mpa. The proposed model separates time dependent part with characteristic material part and regards main variable as elastic modulus, which represents material characteristic and history. To find parameters of the model, we had creep, shrinkage and basic material tests about four FCM bridges. All specimens were tested with same condition, after 3days, 28days and 90days of curing. Also, exposed condition and closed condition were separately given to compare the data of each bridge. Finally, all creep data of four FCM bridges were compared to proposed rheological model and other proposed world code models, AASHTO, ACI, CEB-FIP, JSCE and etc.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.27 no.6
• /
• pp.914-922
• /
• 2003

In this paper, the strain localization of voided ductile material has been analyzed by nonlocal plasticity formulation in which the yield strength not only depends on an equivalent plastic strain measure (hardening parameter), but also on the Laplacian thereof. The gradient terms in yield criterion show an important role on modeling strain-softening phenomena of material. The influence of the mesh size on the elastic -plastic deformation behavior and the effect of the characteristic length parameter for localization prediction are also investigated. The proposed nonlocal plasticity shows that the load -strain curves converge to one curve. Results using nonlocal plasticity also exhibit the dependence of mesh size is much less sensitivity than that for a corresponding local plasticity formulation.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.20 no.5
• /
• pp.425-429
• /
• 2007

A linear ultrasonic motor was designed by a combination of the longitudinal and bending mode. linear ultrasonic motors are based on an elliptical motion on the surface of elastic body, such as bar or plates. The corresponding eigen-mode of one resonance frequency can be excited twice at the same time with a phase shift of 90 degrees in space and time. That is excite symmetric and anti-symmetric modes. Then it determines the thrust and speed of the motor. Linear ultrasonic motors are investigated experimentally in according to be fabricated a general classification to motor structure and material characteristic. There was the first to simulate as use of finite element analysis ANSYS 9.0. The AL-T2W8-ARM14-LEG18-ANGLE80 motor has a maxim efficiency 18 % under the speed 0.14 m/s, thrust 345 gf and preload 280 gf, operating frequency is 57.6 kHz.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.59 no.10
• /
• pp.1770-1775
• /
• 2010

An acceleration life test for rubber gasket of pole transformer was performed. The Arrhenius method was applied as an accelerated degradation test. The failure mode was considered as an elongation, and the failure mechanism is counted as a heat. It is found that both the current material(NBR: Nitrile Butadiene Rubber) and recommended alternative material(HNBR: Hydrogenated Nitrile Butadiene Rubber) have the same Weibull distribution as a life characteristic. For life expectation 95% reliability level of characteristic life is used at using temperature. The test results for NBR and HNBR are 7.7 years and 28.0 years on $50^{\circ}C$ of using temperature, respectively.

• The Journal of the Acoustical Society of Korea
• /
• v.7 no.2
• /
• pp.65-73
• /
• 1988

In this paper, V(z) curve has been analyzed theoretically and compared with the experimental result, and the relation between the V(z) curve and the material characteristic has been studied. Angular spectrum and ray optics theory have been used for theoretical analysis and the acoustic microscope operating at a center frequency of 3 MHz has been used for experiment. In experiment, it has been shown that each material has a V(z) curve of a unique form and the interval of dips appearing in the V(z) curves have been used to determine the Rayleigh wave velocity.

• KIEE International Transaction on Electrical Machinery and Energy Conversion Systems
• /
• v.2B no.4
• /
• pp.149-155
• /
• 2002

This paper presents magnetic field analysis technology that uses a vector magnetic characteristic. Recently the magnetic material was found to be measurable using the vector quantity technique. Therefore considering the anisotropy of the magnetic material in the vector field analysis is necessary. The magnetic field analysis method, which is considered the anisotropy by combining the finite element method with the E&$S^2$ (Enokizono, Soda, and Shimoji) modeling, is applied to a permanent magnet motor model.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2006.12a
• /
• pp.58-62
• /
• 2006

The purpose of this paper is characteristic analysis of permanent magnet generator (PMG) for automatic voltage regulator (AVR)power of brush less synchronous generator. However, this PMG has a spoke type permanent magnet rotor with large overhang for high power density, characteristic analysis considering concentration effect of air-gap flux density due to the overhang should be performed. 30 transient finite element method (FEM)analysis is good solution for overhang parameter, but this method needs too much calculation time. In this paper, we examined the overhang effects based on overhang length and material of rotor core by using 20 and 30 static FEM analysis, and proposed 20 dynamic FEA model considering overhang parameter which gives good and rapid results. The proposed method is verified by the test results of no load, load and short circuit test.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.20 no.3
• /
• pp.16-23
• /
• 2021

The fracture characteristic of the bonded interface under the application of a sliding load to a double cantilevered specimen manufactured using lightweight material was examined. Inhomogeneously bonded materials such as Al6061-T6, CFRP, and CFRP-Al were employed. In the experiment, the specimen was loaded on both directions by applying a shearing load to the bonding interface. The experimentally obtained stress, specific strength and energy release rate values were examined. CFRP exhibited excellent specific strength. The experimental results demonstrated that the inhomogeneous bonded material CFRP-Al exhibited an overall high performance in comparison with the single materials.

• Journal of Conservation Science
• /
• v.37 no.6
• /
• pp.738-747
• /
• 2021

This study attempted to investigate the metallurgical characteristic through material scientific analysis of hammer scale produced as a direct smelting method restoration experiment for each raw material of iron. To this end, four hammer scale groups were set up, respectively, by experimenting with Gyeongju-Gampo Iron sand and Yangyang Iron ore. For the analysis, principal component analysis, compound analysis, microstructure observation, and chemical composition were confirmed. As a result of principal component analysis, as forging and refining progressed, the content of Fe increased and the content of non-metallic objects decreased. As a result of compound analysis, iron oxide-based compounds were identified. As a result of confirming microstructure and chemical composition, Wüstite and Fayalite were observed overall, and agglomerated Wüstite were observed in some. Magnetite on shape of polygon and pillar was observed. In addition, it was confirmed that internal defects, impurities, and non-metallic interventions gradually decreased. In the future, it is necessary to investigate the metallurgical characteristic through material scientific analysis of hammer scale produced through restoration experiments using various raw material of iron, and compare them with those excavated from Iron manufacture ruins.

• Journal of KSNVE
• /
• v.6 no.6
• /
• pp.749-754
• /
• 1996

In this paper, a design method of matching layers is presented for the sandwich type broad band underwater acoustic vibrators. The characteristic impedances of matching layers are determined to be matched to the characteristic impedance of head mass material. For the dynamic characteristic analysis of the sandwich type transducers, one dimensional FEM technique is also introduced. A test vibrator with the quarter wave matching layers has been designed to verify the proposed method. And the wide band characteristics of the input impedance and transmitting voltage response (TVR) are investigated.