• Journal of the Korean Society of Safety
• /
• v.35 no.6
• /
• pp.32-45
• /
• 2020

The problem of determining the discharge rates of gases from pressurized vessels through pressure relief devices was dealt with comprehensively. First, starting from basic fluid flow equations, detailed modeling procedures were presented for isentropic nozzle flows and frictional flows in a pipe, respectively. Meanwhile, physical explanations were given to choking phenomena in terms of the acoustic velocity, elucidating the widespread use of Mach numbers in gas flow models. Frictional flows in a pipe were classified into adiabatic, isothermal, and general flows according to the heat transfer situation around the pipe, but the adiabatic flow model was recommended suitable for gas discharge through pressure relief devices. Next, for the isentropic nozzle flow followed by adiabatic frictional flow in the pipe, two equations were established for two unknowns that consist of the Mach numbers at the inlet and outlet of the pipe, respectively. The relationship among the ratio of downstream reservoir pressure to upstream pressure, mass flux, and total frictional loss coefficient was shown in various forms of MATLAB 2-D plot, 3-D surface plot and contour plot. Then, the profiles of gas properties and velocity in the pipe section were traced. A method to quantify the relationship among the pressure head, velocity head, and total friction loss was presented, and was used in inferring that the rapid increase in gas velocity in the region approaching the choked flow at the pipe outlet is attributed to the conversion of internal energy to kinetic energy. Finally, the Levenspiel chart reproduced in this work was compared with the Lapple chart used in API 521 Standatd.

• Journal of KIBIM
• /
• v.9 no.4
• /
• pp.51-61
• /
• 2019

In the general manufacturing sector, prototyping used to reduce the risks that can arise with new conceptual products. However, in AEC area, it does not mass-produce a building, so the prototype itself becomes a building. Therefore, it is challenging to have prototyping of the same scale as the real thing, and the prototyping process in architecture is very inefficient. The prototyping process in the design stage typically assumes making a scaled model, partial model, or digital model. However, it is difficult for these models to correspond to the actual building and the environment of time and space such as scale, material, environment, load, physical properties and deformation, corrosion, etc., unlike the actual building. When using the digital twin concept in the prototyping process, it is possible to measure performance from the design stage to the operation stage. The digital twin was found by a method for monitoring based on physical twins and real-time linkage in the operation stage. Therefore, if the digital twin concept is applied at the design stage, it is possible to predict performance using not only current performance but also history information using real-time information. In order to apply the digital twin concept to the prototyping design process, we analyze the theoretical considerations and the prototyping design process of the digital twin, analyze the cases and research results where the prototyping design was applied, Provide an applied prototyping design process. The proposed process is tested through a pilot project and analyzed for potential use.

• Journal of Microbiology and Biotechnology
• /
• v.31 no.2
• /
• pp.327-337
• /
• 2021

Fibrinolytic enzymes with a direct mechanism of action and safer properties are currently requested for thrombolytic therapy. This paper reports on a new enzyme capable of degrading blood clots directly without impairing blood coagulation. This enzyme is also non-cytotoxic and constitutes an alternative to other thrombolytic enzymes known to cause undesired side effects. Twenty-four Bacillus isolates were screened for production of fibrinolytic enzymes using a fibrin agar plate. Based on produced activity, isolate S127e was selected and identified as B. subtilis using the 16S rDNA gene sequence. This strain is of biotechnological interest for producing high fibrinolytic yield and consequently has potential in the industrial field. The purified fibrinolytic enzyme has a molecular mass of 27.3 kDa, a predicted pI of 6.6, and a maximal affinity for Ala-Ala-Pro-Phe. This enzyme was almost completely inhibited by chymostatin with optimal activity at 48℃ and pH 7. Specific subtilisin features were found in the gene sequence, indicating that this enzyme belongs to the BPN group of the S8 subtilisin family and was assigned as AprE127. This subtilisin increased thromboplastin time by 3.7% (37.6 to 39 s) and prothrombin time by 3.2% (12.6 to 13 s), both within normal ranges. In a whole blood euglobulin assay, this enzyme did not impair coagulation but reduced lysis time significantly. Moreover, in an in vitro assay, AprE127 completely dissolved a thrombus of about 1 cc within 50 min and, in vivo, reduced a thrombus prompted in a rat tail by 11.4% in 24 h compared to non-treated animals.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.24 no.5
• /
• pp.21-33
• /
• 2020

In this study, the program for system analysis of an expander cycle rocket engine using liquid hydrogen as a fuel was developed. The properties of hydrogen were considered by the ratio of isomers with temperature. The analysis procedure was established with the open and closed types of the expander cycle engine and the simulation methods were suggested for each component. To validation of the analysis program, we compared the performance of the engine operating point and the analysis results performed overseas for Vinci and SE-21D, which are expander cycle engines. As a result of the analysis, the main performance factors of the system, such as the mass flow of the propellant, specific thrust, and power, except for some of the inaccurate input information, showed high accuracy with an error of around 1-2%.

• Journal of Microbiology and Biotechnology
• /
• v.32 no.1
• /
• pp.99-109
• /
• 2022

This study is the first report on production and characterization of the enzyme from an Ornithinibacillus species. A 4.2-fold increase in the extracellular protease (called L9^T) production from Ornithinibacillus caprae L9^T was achieved through the one-factor-at-a-time approach and response surface methodological optimization. L9^T protease exhibited a unique protein band with a mass of 25.9 kDa upon sodium dodecyl sulfate-polyacrylamide gel electrophoresis. This novel protease was active over a range of pH (4-13), temperatures (30-80℃) and salt concentrations (0-220 g/l), with the maximal activity observed at pH 7, 70℃ and 20 g/l NaCl. Proteolytic activity was upgraded in the presence of Ag⁺, Ca²⁺ and Sr²⁺, but was totally suppressed by 5 mM phenylmethylsulfonyl fluoride, which suggests that this enzyme belongs to the serine protease family. L9^T protease was resistant to certain common organic solvents and surfactants; particularly, 5 mM Tween 20 and Tween 80 improved the activity by 63 and 15%, respectively. More importantly, L9^T protease was found to be effective in dehairing of goatskins, cowhides and rabbit-skins without damaging the collagen fibers. These properties confirm the feasibility of L9^T protease in industrial applications, especially in leather processing.

• Archives of Plastic Surgery
• /
• v.49 no.4
• /
• pp.494-500
• /
• 2022

Background Seroma formation is the most common donor site complication following autologous breast reconstruction, along with hematoma. Seroma may lead to patient discomfort and may prolong hospital stay or delay adjuvant treatment. The aim of this study was to compare seroma rates between the deep inferior epigastric perforator (DIEP), transverse musculocutaneous gracilis (TMG), and superior gluteal artery perforator (SGAP) donor sites. Methods The authors conducted a retrospective single-center cohort study consisting of chart review of all patients who underwent microsurgical breast reconstruction from April 2018 to June 2020. The primary outcome studied was frequency of seroma formation at the different donor sites. The secondary outcome evaluated potential prognostic properties associated with seroma formation. Third, the number of donor site seroma evacuations was compared between the three donor sites. Results Overall, 242 breast reconstructions were performed in 189 patients. Demographic data were found statistically comparable between the three flap cohorts, except for body mass index (BMI). Frequency of seroma formation was highest at the SGAP donor site (75.0%), followed by the TMG (65.0%), and DIEP (28.6%) donor sites. No association was found between seroma formation and BMI, age at surgery, smoking status, diabetes mellitus, neoadjuvant chemotherapy, or DIEP laterality. The mean number of seroma evacuations was significantly higher in the SGAP and the TMG group compared with the DIEP group. Conclusion This study provides a single center's experience regarding seroma formation at the donor site after microsurgical breast reconstruction. The observed rate of donor site seroma formation was comparably high, especially in the TMG and SGAP group, necessitating an adaption of the surgical protocol.

• Food Science of Animal Resources
• /
• v.42 no.1
• /
• pp.46-60
• /
• 2022

In this study, angiotensin-I-converting enzyme inhibitory (ACEI) activity was evaluated in fermented goat milk fermented by lactic acid bacteria (LAB) from fermented foods and breast milk. Furthermore, the potential for ACEI peptides was identified in fermented goat milk with the highest ACEI activity. The proteolytic specificity of LAB was also evaluated. The 2% isolate was inoculated into reconstituted goat milk (11%, w/v), then incubated at 37℃ until pH 4.6 was reached. The supernatant produced by centrifugation was analyzed for ACEI activity and total peptide. Viable cell counts of LAB and titratable acidity were also evaluated after fermentation. Peptide identification was carried out using nano liquid chromatography mass spectrometry (LC-MS/MS), and potential as an ACEI peptide was carried out based on a literature review. The result revealed that ACEI activity was produced in all samples (20.44%-60.33%). Fermented goat milk of Lc. lactis ssp. lactis BD17 produced the highest ACEI activity (60.33%; IC₅₀ 0.297±0.10 mg/mL) after 48 h incubation, viable cell counts >8 Log CFU/mL, and peptide content of 4.037±0.27/mL. A total of 261 peptides were released, predominantly derived from casein (93%). The proteolytic specificity of Lc. lactis ssp. lactis BD17 through cleavage on the amino acid tyrosine, leucine, glutamic acid, and proline. A total of 21 peptides were identified as ACEI peptides. This study showed that one of the isolates from fermented food, namely Lc. lactis ssp. lactis BD17, has the potential as a starter culture for the production of fermented goat milk which has functional properties as a source of antihypertensive peptides.

• Journal of Microbiology and Biotechnology
• /
• v.32 no.4
• /
• pp.522-530
• /
• 2022

In this study we aimed to develop novel ZnO-NP/chitosan/β-glycerophosphate (ZnO-NP/CS/β-GP) antibacterial hydrogels for biomedical applications. According to the mass fraction ratio of ZnO-NPs to chitosan, mixtures of 1, 3, and 5% ZnO-NPs/CS/β-GP were prepared. Using the test-tube inversion method, scanning electron microscopy and Fourier-transform infrared spectroscopy, the influence of ZnO-NPs on gelation time, chemical composition, and cross-sectional microstructures were evaluated. Adding ZnO-NPs significantly improved the hydrogel's antibacterial activity as determined by bacteriostatic zone and colony counting. The hydrogel's bacteriostatic mechanism was investigated using live/dead fluorescent staining and scanning electron microscopy. In addition, crystal violet staining and MTT assay demonstrated that ZnO-NPs/CS/β-GP exhibited good antibacterial activity in inhibiting the formation of biofilms and eradicating existing biofilms. CCK-8 and live/dead cell staining methods revealed that the cell viability of gingival fibroblasts (L929) cocultured with hydrogel in each group was above 90% after 24, 48, and 72 h. These results suggest that ZnO-NPs improve the temperature sensitivity and bacteriostatic performance of chitosan/β-glycerophosphate (CS/β-GP), which could be injected into the periodontal pocket in solution form and quickly transformed into hydrogel adhesion on the gingiva, allowing for a straightforward and convenient procedure. In conclusion, ZnO-NP/CS/β-GP thermosensitive hydrogels could be expected to be utilized as adjuvant drugs for clinical prevention and treatment of peri-implant inflammation.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.35 no.4
• /
• pp.377-385
• /
• 2022

Thermal batteries are specialized as primary reserve batteries that operate when the internal heat source is ignited and the produced heat (450~550℃) melts the initially insulating salt into highly conductive eutectic electrolyte. The heat source is composed of Fe powder and KClO₄ with different mass ratios and is inserted in-between the cells (stacks) to allow homogeneous heat transfer and ensure complete melting of the electrolyte. An ideal heat source has following criteria to satisfy: sufficient mechanical durability for stacking, appropriate heat calories, ease of combustion by an igniter, stable combustion rate, and modest peak temperature. To satisfy the aforementioned requirements, Fe powder must have high surface area and porosity to increase the reaction rate. Herein, the hydrothermal and spray drying synthesis techniques for Fe powder samples are employed to investigate the physicochemical properties of Fe powder samples and their applicability as a heat source constituent. The direct comparison with the state-of-the-art Fe powder is made to confirm the validity of synthesized products. Finally, the actual batteries were made with the synthesized iron powder samples to examine their performances during the battery operation.

• Membrane and Water Treatment
• /
• v.13 no.5
• /
• pp.235-243
• /
• 2022

The paper presents the effect of operating temperatures and flow rates on the distillate flux that can be obtained from a hydrophobic membrane having the characteristics: pore size of 0.15 ㎛; thickness of 130 ㎛; and 85% porosity. That membrane in the present investigation could be the direct contact (DCMD) or the air-gap membrane distillation (AGMD). To model numerically the membrane distillation processes, the two-dimensional computational fluid dynamic (CFD) is used for the DCMD and AGMD cases here. In this work, DCMD and AGMD models have been validated with the experimental data using different flows (Parallel and Counter-current flows) in non-steady-state situations. A good agreement is obtained between the present results and those of the experimental data in the literature. The new approach in the present numerical modeling has allowed examining effects of the nature of materials (Polyvinylidene fluoride (PVDF) polymers, copolymers, and blends) used on thermal properties. Moreover, the effect of the area surface of the membrane (0.021 to 3.15 ㎡) is investigated to explore both the laminar and the turbulent flow regimes. The obtained results found that copolymer P(VDF-TrFE) (80/20) is more effective than the other materials of membrane distillation (MD). The mass flux and thermal efficiency reach 193.5 (g/㎡s), and 83.29 % using turbulent flow and an effective area of 3.1 ㎡, respectively. The increase of feed inlet temperatures and its flow rate, with the reduction of cold temperatures and its flow rate are very effective for increasing distillate water flow in MD applications.