• Bulletin of the Korean Chemical Society
• /
• v.25 no.11
• /
• pp.1661-1666
• /
• 2004

The reaction of titanium tetraisopropoxide with 2 equiv of N,N-diethyl acetoacetamide affords Ti($O^iPr)_2(CH_3COCHCONEt_2)_2$ (1) as colorless crystals in 80% yield. Compound 1 is characterized by spectroscopic (Mass and $^1H/^{13}C$ NMR) and microanalytical data. Molecular structure of 1 has been determined by a single crystal X-ray diffraction study, which reveals that it is a monomeric, cis-diisopropoxide and contains a six coordinate Ti(IV) atom with a cis($CONEt_2$), trans($COCH_3$) configuration (1a) in a distorted octahedral environment. Variable-temperature $^1H$ NMR spectra of 1 indicate that it exists as an equilibrium mixture of cis, trans (1a) and cis, cis (1b) isomers in a 0.57 : 0.43 ratio at -20$^{\circ}C$ in toluene-$d_8$ solution. Thermal properties of 1 as a MOCVD precursor for titanium dioxide films have been evaluated by thermal gravimetric analysis and vapor pressure measurement. Thin films of pure anatase titanium dioxide (after annealing above 500$^{\circ}C$ under oxygen) have been grown on Si(100) with precursor 1 in the substrate temperature range of 350- 500$^{\circ}$ using a bubbler-based MOCVD method.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.12 no.4
• /
• pp.33-41
• /
• 2008

The prelaunch thermal transients in the cryogenic oxidizer tank of liquid propulsion rocket subjected to uniform heat flux from outside are numerically analyzed through thermodynamic equations and heat and mass transfer relations. The prelaunch stage is assumed to be composed of five idealized sub-stages including pressurization process by helium gas injection. The Peng-Robinson equation of state is utilized in the lumped analysis of ullage gas. The liquid region is divided into a number of horizontal layers of uniform properties to account for the thermal stratification. The computational result for the typical case shows that the temperature rise of liquid oxidizer is less than 1K and the adsorbed helium into the liquid is approximately 10g.

• Journal of Ginseng Research
• /
• v.41 no.3
• /
• pp.379-385
• /
• 2017

In this study, white ginseng was used as the raw material, which was fermented with Paecilomyces hepiali through solid culture medium, to produce ginsenosides with modified chemical composition. The characteristic chemical markers of the products thus produced were investigated using rapid resolution liquid chromatography coupled with quadrupole time-of-flight mass spectrometry (RRLC-QTOF-MS). Chemical profiling data were obtained, which were then subjected to multivariate statistical analysis for the systematic comparison of active ingredients in white ginseng and fermented ginseng to understand the beneficial properties of ginsenoside metabolites. In addition, the effects of these components on biological activity were investigated to understand the improvements in the phagocytic function of macrophages in zebrafish. According to the established RRLC-QTOF-MS chemical profiling, the contents in ginsenosides of high molecular weight, especially malonylated protopanaxadiol ginsenosides, were slightly reduced due to the fermentation, which were hydrolyzed into rare and minor ginsenosides. Moreover, the facilitation of macrophage phagocytic function in zebrafish following treatment with different ginseng extracts confirmed that the fermented ginseng is superior to white ginseng. Our results prove that there is a profound change in chemical constituents of ginsenosides during the fermentation process, which has a significant effect on the biological activity of these compounds.

• Journal of the Korea Convergence Society
• /
• v.11 no.5
• /
• pp.61-72
• /
• 2020

An anti-aging peptide was prepared from fish collagen hydrolysate (FCH) by ultrafiltration (MWCO; 1 kDa) and reversed-phased high performance liquid chromatography (RP-HPLC). Its anti-aging properties were evaluated based on the procollagen-synthesizing and MMP-1-inhibiting activities in Hs68 cells. A potent anti-aging peptide (fraction I-I) increased collagen synthesis by 46% and also inhibited MMP-1 secretion by 77%, compared with unpurified FCH. The amino acid sequence of fraction I-I was identified to be Gly-Arg-Arg-Gly-Asn-Lys (GRRGNK; the repeating Gly-X-Y sequence in collagen), and it had a molecular mass of 686.175 Da. It revealed that the anti-aging activity of GRRGNK was mainly due to skin protective effects. These results demonstrated that fish collagen hydrolysate may be a potential source of anti-aging peptides, which could be utilized in various field, including foods, cosmetics, and pharmaceuticals.

• Korean Chemical Engineering Research
• /
• v.54 no.2
• /
• pp.175-180
• /
• 2016

The fluorine-containing modified polyurea was synthesized using the PTPE-diol to improve the ozone-resistance. Three types (PFDIA-10C, PFDIA-20C, PFDIA-30C) of the modified polyurea containing the fluorine content from 10 wt% to 30 wt% were prepared. After ozone treatment on the prepared films, the weight loss of film was investigated and analyzed the film properties such as hardness, wear resistance, tensile stress, elongation, etc. Also, the film surfaces were observed by the optical microscopy after ozone-resistance tests at 10 ppm for 336 h. It was shown that the defects such as the cracking, the bleaching and the mass loss were reduced and the ozone-resistance of films were improved when the contents of PFPE-diol are more than 20 wt%. It was found that the intensity of O-H peak in PFDIA compounds confirmed by FT-IR was decreased as fluorine contents were increasing.

• Journal of the Korean Ceramic Society
• /
• v.56 no.3
• /
• pp.211-232
• /
• 2019

Porous ceramics are promising materials for a number of functional and structural applications that include thermal insulation, filters, bio-scaffolds for tissue engineering, and preforms for composite fabrication. These applications take advantage of the special characteristics of porous ceramics, such as low thermal mass, low thermal conductivity, high surface area, controlled permeability, and low density. In this review, we emphasize the direct foaming method, a simple and versatile approach that allows the fabrication of porous ceramics with tailored microstructure, along with distinctive properties. The wet foam stability is achieved under the controlled addition of amphiphiles to the colloidal suspension, which induce in situ hydrophobization, allowing the wet foam to resist coarsening and Ostwald ripening upon drying and sintering. Different components, like contact angle, adsorption free energy, air content, bubble size, and Laplace pressure, play vital roles in the stabilization of the particle stabilized wet foam to the porous ceramics. The mechanical behavior of the load-displacements curves of sintered samples was investigated using Herzian indentations testes. From the collected results, we found that microporous structures with pore sizes from 30 ㎛ to 570 ㎛ and the porosity within the range from 70% to 85%.

• KEPCO Journal on Electric Power and Energy
• /
• v.1 no.1
• /
• pp.115-120
• /
• 2015

$K_2CO_3$-based dry regenerable sorbents were prepared by spray-drying techniques to improve mass produced $K_2CO_3-Al_2O_3$ sorbents (KEP-CO2P, hereafter), and then tested for their $CO_2$ sorption capacity by a $2,000Nm^3/h$ (0.5 MWe) $CO_2$ capture pilot plant built for Unit 3 of the Hadong thermal power station in 2010. Each of the sample sorbents contained 35 wt.% $K_2CO_3$ as the active materials with various support materials such as $TiO_2$, MgO, Zeolite 13X, $Al_2O_3$, $SiO_2$ and hydrotalcite (HTC). Their physical properties and reactivity were tested to evaluate their applicability to a fluidized-bed or fast transport-bed $CO_2$ capture process. The $CO_2$ sorption capacity and percentage utilization of $K_2CO_3$-MgO based sorbent, Sorb-KM2, was $8.6g-CO_2/100g$-sorbents and 90%, respectively, along with good mechanical strength for fluidized-bed application. Sorbs-KM2 and KT were almost completely regenerated at $140^{\circ}C$. No degradation of Sorb-KM by $SO_2$ added as a pollutant in flue gas was observed during a cycle test.

• Journal of Surface Science and Engineering
• /
• v.29 no.5
• /
• pp.345-349
• /
• 1996

The wetting property of polymer surfaces is very important for practical applications. Plasma source ion implantation technique was used to improve the wetting properties of polymer surfaces. Poly(ethylene terephtalate) and other polymer sheets were mounted on the target stage and an RF plasma was generated by means of an antenna located inside the vacuum chamber. High voltage pulses of up to -10kV, 10 $\mu$sec, and up to 1 kHz were applied to the stage. The samples were implanted for 5 minutes with using Ar, $N_2,O_2,CH_4,CF_4$ and their mixture as source gases. A contact angle meter was used to measure the water contact angles of the implanted samples and of the samples stored in ambient conditions after implantation. The modified surfaces were analysed with Time-Of-Flight Mass Spectrometer (TOF-SIMS) and Auger Electron Spectroscopy (AES). The oxygen-implanted samples showed extremely low water contact angles of $3^{\circ}C$ compared to $79^{\circ}C$ of unimplanted ones. Furthermore, the modified surfaces were relatively stable with respect to aging in ambient conditions, which is one of the major concerns of the other surface treatment techniques. From TOF-SIMS analysis it was found that oxygen-containing functional groups had been formed on the implanted surfaces. On the other hand, the $CF_4$-implanted samples turned out to be more hydro-phobic than unimplanted ones, giving water contact angles exceeding $100^{\circ}C$ . The experiment showed that plasma source ion implantation is a very promising technique for polymer surface modification especially for large area treatment.

• The Journal of Engineering Geology
• /
• v.18 no.2
• /
• pp.177-183
• /
• 2008

In the study, we carried out a 3-D analysis to assess the influence of groundwater level changes on the slope stability, conducting a series of back-numerical analysis to delineate the critical line of the shear strength of the failure surface of a landslide, and a laboratory test to determine the geo-mechanical properties of soil samples. The analysis result shows that the shear strength determined by the laboratory test was distributed below the critical line of shear strength estimated by back-analysis. Differences between driving and resisting force were also analyzed in groundwater conditions of dry and saturation. It appeared that the stress gets greater towards the slope center of the landslide, and the debris mass moves downwards. According to the analysis, the factor of safety becomes 1 with the rise of foundwater level up to -0.85 m from the slope surface, while the slope tends to stay stable during dry seasons.

• Journal of Microbiology and Biotechnology
• /
• v.18 no.5
• /
• pp.852-858
• /
• 2008

An extracellular protease (Mc1) was isolated from the nematode-trapping fungus Monacrosporium cystosporium by gel filtration, anion-exchange, and hydrophobic interaction chromatographies. This protease had a molecular mass of approximately 38 kDa and displayed an optimal activity at pH 7-9 and $56^{\circ}C$ (over 30 min). Its proteolytic activity was highly sensitive to the serine protease inhibitor PMSF (phenylmethylsulfonylfluoride, 0.1 mM), indicating that it belonged to the serine-type peptidase group. The Michaelis constant ($K_m$) and $V_max$ for substrate N-Suc-Ala-Ala-Pro-Phe-pNA were $1.67{\times}10^{-4}\;M$ and 0.6071 $OD_{410}$ per 30 s, respectively. This protease could degrade a broad range of substrates including casein, gelatin, BSA (bovine serum albumin), and nematode cuticle. Moreover, the enzyme could immobilize the free-living nematode Panagrellus redivivus and the pine wood nematode Bursaphelenchus xylophilus, suggesting that it might playa role in infection against nematodes. The encoding gene of Mc1 was composed of one intron and two exons, coding for a polypeptide of 405 amino acid residues. The deduced amino acid sequence of Mcl showed 61.4-91.9% identity to serine proteases from other nematode-trapping fungi. Our results identified that Mcl possessed biochemical properties including optimal reaction condition and substrate preference that are different from previously identified serine proteases.