• Journal of the Society of Naval Architects of Korea
• /
• v.55 no.6
• /
• pp.490-496
• /
• 2018

The consistency of the initially designed waves in the domain is essential for accurate calculation of the added resistance in waves through CFD. In particular, unwanted reflected waves at domain boundaries can cause incorrect numerical solutions due to the superposition with initially designed waves. Euler Overlay Method(EOM) is one of the methods for reducing wave reflections by adding an additional source term to momentum and phase conservation equations, respectively. In this study, we apply the Euler Overlay Method(EOM) to the open-source CFD library, OpenFOAM(R), to simulate the accurate free-surface waves in the domain and the parametric study is performed for efficient implementation of Euler Overlay Method(EOM). Considering that the damping efficiency depends on the selection of the overlay parameter in the added source terms, the size of overlay zone and the wave steepness, the influences of these factors are tested through the wave elevation measured at constant time intervals in the 2D numerical wave tank. Through this process, guidelines for selection of optimal overlay parameter and overlay zone size that can be applied according to the scaling law are finally presented.

• Journal of Welding and Joining
• /
• v.32 no.6
• /
• pp.56-63
• /
• 2014

To develop and understand dissimilar metals joining of Stainless steel and Copper, ultra-high speed laser lap welding was studied using single mode fiber laser in this study. SUS304 and Cu have large differences in materials properties, and Cu and Fe have no intermetallic compounds by typical binary phase of Cu and Fe system. In this study, ultra-high speed lap welds of SUS304 and Cu dissimilar metals using single-mode fiber laser was generated, and weldability of the weld fusion zone was evaluated using a tensile shear test. To understand the phenomenon of tensile shear load, weld fusion zone of interface weld area and fracture parts after tensile shear test were observed using scanning electron microscopy (SEM) and energy dispersive X-ray spectroscopy (EDX) analysis system. And it was confirmed that Cu was easily melting and penetrating in the grain boundaries of SUS304 because of low melting temperature. And high thermal conductivity of copper occurred dissipate heat energy rapidly. These properties cause the solidification cracking in weld zone.

• Journal of Fisheries and Marine Sciences Education
• /
• v.27 no.6
• /
• pp.1717-1726
• /
• 2015

Acceleration of globalization in almost all industries, including fisheries, already had been a major paradigm of the age. And It has been weakened its meaning of geographical, cultural and economic boundaries between the nations. In particular, various changes in the fisheries environment have exceeded the area of problem for conventional single country is resolved. And if there is no cooperation with international cooperation other problems also almost nearly impossible to alleviate or solve. So it has emerged in this context, the concept of sustainable development and conceptual diagram of responsible fisheries. However, it has been passed about 20 years since the FAO documents published, there is little interest in it. In this study, analyzed the characteristics of the changes and its constitutive trends and contents of the FAO's responsible fisheries documents. And proposed both the need for analysis and research for the fisheries in an international context for the future and educational aspects. The results of this study show that FAO related documents are hardly to find that have been translated into Korean, in particular since the 2000s. And it is fairly skeptical whether there is a direct effective in fisheries in terms of language barriers. Therefore, the study on responsible fisheries much more important to develop the current status and future-oriented policy of international fisheries even in fisheries related education.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2004.03b
• /
• pp.491-498
• /
• 2004

In recent years, as an effort to grasp the leading position in the field of maritime trading, new ports and container terminals arc now under construction. Old ports are extended. At the beginning, stones were thrown down to form stone embankments, that is stone-dams, in the outer and inner boundaries of the planned reclamation-land. S.C.P(Sand Compaction Pile) works are often needed to improve the stability of stone-dams, where marine sediments arc relatively thick. Here, interests are centered on the shape of stone body. In this, drilling work won't provide a sufficient resolution. In addition, the result corresponds to only one borehole point information. Thus, the aim of this paper is to introduce an affordable technology, that is, a combined geophysical method(seismic tomography + Televiewer) enables to get the whole information about stone-dam section. The measuring and evaluating procedure is described in detail with an emphasis on dealing with the use of seismic detonator, proper borehole deployment and integrated data analysis. Examples of field experiments at Busan new port are illustrated, which will prove the benefit of combined geophysical method.

• Journal of Advanced Marine Engineering and Technology
• /
• v.28 no.8
• /
• pp.1270-1278
• /
• 2004

This paper describes the effectiveness of laser pulse shaping in eliminating weld defects such as porosity, cracks and undercuts in pulsed Nd:YAG laser welding. A large porosity was formed in a keyhole mode of deeply penetrated weld metal of any stainless steel. Solidification cracks were present in STS 310S with above 0.017%P and undercuts were formed in STS 303 with about 0.3%S. The conditions for the formation of porosity were determined in further detail in STS 316. With the objectives of obtaining a fundamental knowledge of formation and prevention of weld defects, the fusion and solidification behavior of a molten puddle was observed during laser spot welding of STS 310S through a high speed video photographing technique. It was deduced that cellular dendrite tips grew rapidly from the bottom to the surface, and consequently residual liquid remained at the grain boundaries in wide regions and enhanced the solidification cracking susceptibility. Several laser pulse shapes were investigated and optimum pulse shapes were proposed for the reduction and prevention of porosity and solidification cracking.

• Journal of Korean Society of Coastal and Ocean Engineers
• /
• v.2 no.4
• /
• pp.223-230
• /
• 1990

Suspended materials during maritime construction works may cause surrounding environmental changes Therefore, it is important to know the behavior of the muddy water lumps caused by dropping soil in coastal areas. Two-dimensional behaviors of the muddy water moving along the inclined boundaries are investigated experimentally, which are the change of height, length, and moving velocity, the properties of movement at the head of muddy water, the coefficient of entrainment and shape, and the accumulation shape. The shape of the muddy water lumps was similar with the slope thermal. Therefore, the moving characteristics were found to be described using turbulence theory.

• Journal of the Korean Society of Industry Convergence
• /
• v.26 no.1
• /
• pp.133-141
• /
• 2023

Accurate measurement of seafloor topography plays a crucial role in developing marine industries such as maritime safety, resource exploration, environmental protection, and coastal management. The seafloor topography is constructed using side scan sonar (SSS) and single beam echosounder (SBES) or multibeam echosounder (MBES), which transmit and receive ultrasound waves through a device attached to a marine survey vessel. However, the use of a sonar system is affected by noise pollution areas, and the single beam has a limited scope of application. At the same time, the multibeam is mainly applicable for depth observation. For these reasons, it is difficult to determine the boundaries and areas of seafloor topography. Therefore, this study proposes a method to improve the backscatter data of multibeam echosounder, which has a relationship with the seafloor quality, by using digital image processing to classify the shape of the underwater surface.

• The Sea:JOURNAL OF THE KOREAN SOCIETY OF OCEANOGRAPHY
• /
• v.28 no.2
• /
• pp.63-93
• /
• 2023

This study aims to examine the history of naming the strait between the Yellow and East China Seas and the East Sea to suggest a consistent nomenclature and to demarcate the geographic region of the strait. Although the strait is internationally known as 'Korea Strait', it is commonly referred to as the 'South Sea' in Korean common usage. This review ultimately recommends the use of 'Korea Strait' as an appropriate geographical name for this area. To support this recommendation, the historical boundaries typically assigned to the Korea Strait were investigated. We also analyzed the evolution of geographical labels assigned to Korea Strait and to the Western and Eastern Channels (labels given to the two maritime areas surrounding Tsushima). Resources for this analysis included historic maps and charts, International Hydrographic Organization Special Publications (S-23), and maps published in the Ocean Science Journal (OSJ) and Journal of Oceanography (JO), which are two international journals representing Korean and Japanese sources, respectively, from 2005 to 2021. In these two international journals, the most frequently used names assigned to the strait of interest were Korea Strait (appearing 42.9% of OSJ maps, and 7.5% of JO maps), and Tsushima Strait (appearing 60.4% of JO maps, and 0% of OSJ maps). Other names were South Sea and Korea Strait/Tsushima Strait. On maps in the two reviewed journals, the boundaries of Korea Strait were defined explicitly or implicitly in five different ways: a broad region between the Yellow and East China Seas and Ulleung Basin (Type 1), the region between Ulleung Basin and Tsushima (Type 2), the western channel of the strait (Type 3-1), the eastern channel of the strait (Type 3-2), and both the western and eastern channels of the strait (Type 4). Overall, Type 1 was the most frequently used boundary, taking up 71.4% of OSJ and 60.4% of JO maps. Lastly, we suggest in this paper that the current flowing through Korea Strait from the East China Sea to the East Sea should be labeled the 'Korea Strait Warm Current' to indicate its full path through the strait. Currently, this current is internationally referred to as the 'Tsushima Warm Current', which does not link well to the commonly used geographic name of the strait.

• Journal of the Korea Society of Computer and Information
• /
• v.16 no.9
• /
• pp.69-76
• /
• 2011

According to the related reports, about 60 percents of ship collisions have resulted from operating mistake caused by human factor. Specially, the report said that negligence of observation caused 66.8 percents of the accidents due to a human factor. Hence automatic detection and tracking of an object from an IR images are crucial for safety navigation because it can relieve officer's burden and remedies imperfections of human visual system. In this paper, we present a method to detect an object such as ship, rock and buoy from a sea IR image. Most edge directions of the sea image are horizontal and most vertical edges come out from the object areas. The presented method uses them as a characteristic for the object detection. Vertical edges are extracted from the input image and isolated edges are eliminated. Then morphological closing operation is performed on the vertical edges. This caused vertical edges that actually compose an object be connected and become an object candidate region. Next, reference object regions are extracted using horizontal edges, which appear on the boundaries between surface of the sea and the objects. Finally, object regions are acquired by sequentially integrating reference region and object candidate regions.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.20 no.1
• /
• pp.96-103
• /
• 2014

A liquefied natural gas(LNG) in cryogenic liquid is converted back into gaseous form for distribution to residential and industrial consumers. In this re-gasification process, LNG supplies a plenty of cold thermal energy about $83.7{\times}10^4kJ/kg$. The LNG cold thermal energy is utilized for the re-liquefaction process of cryogenic fluids such as Nitrogen, Hydrogen and Helium, and ice manufacturing process and air-conditioning system in some advanced countries. Therefore, it is also necessary to establish the recovery systems of the LNG cold thermal energy around Incheon, Pyungtaek and Tongyung LNG import terminals in our country. Methane is used as working fluid in this paper, which is the major component of LNG over 85 % by volume, in order to investigate the flow behavior characteristics of LNG with phase change at low heat flux. This paper presents the effects of pipe diameters, pipe inclinations and saturation pressures on the flow boundaries of methane flowing in a cryogenic heat exchanger tube, together with those of nitrogen, propane, R11 and R134a. The outcomes obtained from this theoretical researches are also compared with previous experimental data. It was also found that the effect of pipe inclination on the methane flow boundaries was significant.