• The Sea:JOURNAL OF THE KOREAN SOCIETY OF OCEANOGRAPHY
• /
• v.4 no.4
• /
• pp.400-404
• /
• 1999

The conventional mercury delay method to measure compressional wave velocity of unconsolidated sediment is inconvenient because the signal must be analyzed on the oscilloscope and the mercury column has to be calibrated between measurements. We developed an automated compressional wave velocity measurement technique by connecting an oscilloscope and a PC with a GPIB (General Purpose Interface Bus) card. The GPIB card buses signals from the oscilloscope to the PC where the signal from a sample is analyzed and compared to the input pulse thereby the compressional wave velocity of the sample is computed and recorded automatically. Differences between the mercury delay method and the automated measurement technique are negligible except the slightly greater velocity in the automated measurement technique. We concluded that the new technique can be used to measure the velocity for unconsolidated marine sediment. It also has an advantage to calculate sediment attenuation through the processing of waveform using the spectral ratio technique.

• Journal of the Korean Institute of Navigation
• /
• v.21 no.2
• /
• pp.47-58
• /
• 1997

The purpose of this study is to find out the impacts of VTS on the marine safety and users' opinion on the VTS which have been being operated in the port of Pohang for the last 3 years and is to suggest a guideline to the successful operation of VTS in the future. This study is based upon the questionnaire survey and the respondents include 236 masters/mates of merchant vessels who have visited the port of Pohang and 6 pilots who have been working in the port. From the questionnaire results, this study notes the following conclusions related to the VTS operations. (1) A few of the respondents (mainly foreigners) do not understand the entering procedure of the port and the fundamental concept of VTS. Accordingly, the more active VTS services have to be provided for the mariners. (2) It was found that themost dangerous factors in tehvicinity of the port were the floating materials, fishing nets, andillegal fishing activities inthe fairway. Therefore, the proper surveillance, stricter enforcement of Acts and the instructive education for the fishermen are required to avoid the risks. (3) A majority of the respondents agreed the VTS has contributed to the safety of vessel traffic, and they pointed out ' the assiatances in reduced visibililty conditions' is the most important task of VTS. The amount of 75.6% of the respondents answered that they have experienced the assistance from VTS more than 1 time since the system was established in the port of Pohang . Also 44.2% of the respondents considered they were able to avoid marine casualties such as collision, ramming or agrounding with the VTS assistances. (4) 49.2% of the respondents preferred the passive information services , while, 38.8% of them preferred the positive control advices in the case of encountering any potential risks. VTS iperators have to consider seriously when they provide the positive control advices of ship's course and speed. (5) A majority of the respondents confirmed that the prot and its approaches is suitable for the VTS coverge . To extend the service areas of the VTS and to improve radar detecting ability, the use of radar transponders are seen as the ideal method. (6) A minority of the respondents pointed out 'the improper orders or recommendatinos caused by the poor decision making' firstly, ' the language problem(sea-speaking in English)' secondly, as the deficiency of personal qualification. It seems, therefore, theat the personal efforts of the operators and systematic training programmes for them are necessary to solve the problems.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.28 no.5
• /
• pp.773-779
• /
• 2022

Deep-sea fisheries in Korea play an essential role in supplying popular seafood and providing food security. Countries, as well as the IMO (International Maritime Organization), have attempted to establish an internationally harmonized safety standard for fishing vessels. However, starting with the adoption of 'The Torremolinos International Convention for the Safety of Fishing Vessel 1977', the '2012 Cape Town Agreement' was adopted, but the requirements for enforcement were not met. However, with the 2019 Torremolinos Declaration, the effect of the agreement became visible. Korea is also about to ratify the agreement, and deep-sea fishing vessels are subject to the agreement. The length of the hull or the gross tonnage can be selected as the criteria for applying the 2012 Cape Town Agreement, and this is also partially applied to the existing vessels. Analyzing 188 deep-sea fishing vessels registered as members of the Korea Overseas Fisheries Association to confirm the effect on the existing vessels showed that the application of gross tonnage had little impact on the ratification of the agreement. In addition, laws must be revised for the compulsorization of GMDSS facilities such as two-way VHF and radar transponders and for the safety familiarization of fishermen. In the industry, the facilities required by the agreement must be provided, and the fishermen must be familiarized with safety.

• International Journal of Ocean System Engineering
• /
• v.2 no.3
• /
• pp.185-194
• /
• 2012

A Macroscopic combination of two or more distinct materials is commonly referred to as a "Composite Material", having been designed mechanically and chemically superior in function and characteristic than its individual constituent materials. Composite materials are used not only for aerospace and military, but also heavily used in boat/ship building and general composite industries which we are seeing increasingly more. Regardless of the various applications for composite materials, the industry is still limited and requires better fabrication technology and methodology in order to expand and grow. An example of this is that the majority of fabrication facilities nearby still use an antiquated wet lay-up process where fabrication still requires manual hand labor in a 3D environment impeding productivity of composite product design advancement. As an expert in the advanced composites field, I have developed fabrication skills with the use of machinery based on my past composite experience. In autumn 2011, the Korea government confirmed to fund my project. It is the development of a composite sanding machine. I began development of this semi-robotic prototype beginning in 2009. It has possibilities of replacing or augmenting the exhaustive and difficult jobs performed by human hands, such as sanding, grinding, blasting, and polishing in most often, very awkward conditions, and is also will boost productivity, improve surface quality, cut abrasive costs, eliminate vibration injuries, and protect workers from exposure to dust and airborne contamination. Ease of control and operation of the equipment in or outside of the sanding room is a key benefit to end-users. It will prove to be much more economical than normal robotics and minimize errors that commonly occur in factories. The key components and their technologies are a 360 degree rotational shoulder and a wrist that is controlled under PLC controller and joystick manual mode. Development on both of the key modules is complete and are now operational. The Korean government fund boosted my development and I expect to complete full scale development no later than 3rd quarter 2012. Even with the advantages of composite materials, there is still the need to repair or to maintain composite products with a higher level of technology. I have learned many composite repair skills on composite airframe since many composite fabrication skills including repair, requires training for non aerospace applications. The wind energy market is now requiring much larger blades in order to generate more electrical energy for wind farms. One single blade is commonly 50 meters or longer now. When a wind blade becomes damaged from external forces, on-site repair is required on the columns even under strong wind and freezing temperature conditions. In order to correctly obtain polymerization, the repair must be performed on the damaged area within a very limited time. The use of pre-impregnated glass fabric and heating silicone pad and a hot bonder acting precise heating control are surely required.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.28 no.1
• /
• pp.19-29
• /
• 2022

The result of a questionnaire survey conducted on fishermen using coastal fish traps shows that fall accidents during trap dropping and pulling constitute the highest proportion of accidents at 42.1 %, whereas slipping accidents on the deck or stricture accidents to the body due to the trap winding device constitute 21.1 % each. In addition, 53.2 % of all surveyed subjects responded that trap pulling is the most dangerous task, followed by fish sorting 33.8 %, and trap dropping 9.1 %. As for the main items requested by fishermen for improving the trap winding device, 36.8 % indicated a method to easily lift the trap from the water to the work deck, and 31.6 % indicated a method to overcome the rope tension and prevent slip when pulling the trap to reduce the accidents. The small trap fishing vessel winding device proposed herein can increase the winding force by strengthening the rope contact area and friction coefficient via an appropriate contact angle between the driving roller of the winding device and the rope. When the contact angles between the driving roller and the rope are 1°, 5°, 9°, 14° and 19°, the rope tension showed a difference according to each contact angle. When the contact angle is 9°, the rope tension is the highest at 392.62 kgf. Based on these experimental results, a prototype winding device is manufactured, and 25 traps are installed on a rope with a total length of 100 m at 4 m intervals in the sea, and then the rope tension is measured during trap pulling. As a result, the rope tension increases rapidly at the initial stage of trap pulling and shows the highest value of 31.89 kgf, which subsequently decreases significantly. Therefore, it is appropriate to design the winding force of a small trap fishing vessel winding device based on the maximum tension value of the rope specified at the beginning of the trap pulling operation.

• Journal of Navigation and Port Research
• /
• v.46 no.4
• /
• pp.338-343
• /
• 2022

As the revitalization of the global maritime industry continues, the number of foreign ships navigating the maritime territories of maritime neighboring countries has rapidly increased. However, large-scale marine accidents have occurred, caused by the insufficient establishment of a system for management and operation relative to vessels' safety-condition. To address that, the IMO has granted the right to exercise port state control, especially for foreign vessels, to countries with jurisdiction over maritime territories with strengthening regulations and guidelines. In particular, the Republic of Korea, as a member of the TOKYO MOU, is conducting PSC, but as of 2020, the proportion of foreign ships was three times higher than that of national ships that called in domestic ports. However, the inspection rate was low at 9% which has not met the recommended level by the TOKYO MOU. Thus, this study conducted an IPA analysis as well as content analysis, by collecting the practical opinions and views of PSCO through objective questionnaires and written expert interviews, for improving the efficiency and effectiveness of domestic PSC. As a result, it was derived that the importance and performance related to human factors such as life on board, working environment, and response to safety accidents should be improved in to raise the quality of PSC inspection. Additionally, the work environment and performance of PSC in domestic ports for foreign vessels could be improved, if multifaceted support bases are established, for administrative unification of related tests for PSC, recruitment of PSCO, activation of the defection-reporting system, reorganization of the PSC execution group, etc.

• The Journal of the Acoustical Society of Korea
• /
• v.43 no.4
• /
• pp.400-405
• /
• 2024

When cavitation noise occurs in ship propellers, the level of underwater radiated noise abruptly increases, which can be a critical threat factor as it increases the probability of detection, particularly in the case of naval vessels. Therefore, accurately and promptly assessing cavitation signals is crucial for improving the survivability of submarines. Traditionally, techniques for determining cavitation occurrence have mainly relied on assessing acoustic/vibration levels measured by sensors above a certain threshold, or using the Detection of Envelop Modulation On Noise (DEMON) method. However, technologies related to this rely on a physical understanding of cavitation phenomena and subjective criteria based on user experience, involving multiple procedures, thus necessitating the development of techniques for early automatic recognition of cavitation signals. In this paper, we propose an algorithm that automatically detects cavitation occurrence based on simple statistical features reflecting cavitation characteristics extracted from acoustic signals measured by sensors attached to the hull. The performance of the proposed technique is evaluated depending on the number of sensors and model test conditions. It was confirmed that by sufficiently training the characteristics of cavitation reflected in signals measured by a single sensor, the occurrence of cavitation signals can be determined.

• Journal of Korea Port Economic Association
• /
• v.32 no.4
• /
• pp.149-163
• /
• 2016

Seafarers are an essential resource in maritime industries, which provide navigation skills, vessel maneuvering skills and fishing skills in the fishery industry. They also work as a driving force in pilotage, port operation, vessel traffic service, and marine safety. Other areas in maritime services, which rely on seafarer include safety management of ships, supervisory activities, and maritime accident assessment. In these ways, Korean seafarers have contributed to the growth of Korean economy. However, there have been issues of high separation rate, shortage of supply, multi-nationality, multiplicity of culture caused by employment of foreign seafarers, and aging. The present paper finds that maritime officers and fishery officers demonstrate differences in the statistics of on-board job taking and separation: the separation rate of fishery officers is higher than that of maritime officers. The existing data and statistics by the Korea Seafarer's Welfare & Employment Center could be improved by changing its structure from time series to panel data. The Korea Seafarer's Welfare & Employment Center is the ideal institution for collecting the panel data, as it has already accumulated and published relevant statistics regarding seafarer. The basic design method of the panel data is to adopt and improve it by including the information on ratings of maritime and fishery industries, ranks in a ship, personal information, family life, and career goal. Panel data are useful in short- and long-term forecasts of supply of Korean seafarers; demand evaluation of education, training, and reeducation of the seafarers; demographical dynamic analysis on Korean seafarers; inducement policy of long-term on board job taking in harmony with man-power demands in marine industries such as pilotage service; implementation of job attractiveness policy on Korean seafarers; and employment stabilization of Korean seafarers.

• Journal of Korea Port Economic Association
• /
• v.30 no.1
• /
• pp.175-194
• /
• 2014

Because the thawing of the Arctic ocean is slowly accelerating due to global warming, recently exploring resources in Arctic ocean and transporting resources by using the North Pole route have been getting spotlight. Since the original route transported by the Suez Canal from Korea to Europe could be shorten about 8,000km in distance(decreased about 38% compared to the original route), which means shortening about 10 voyage dates, it is expected to bring huge logistics cost reduction. Once the North Pole route is commercialized successfully, it would be one of the most important variables that affects future of Busan port and guides for economic development of Busan. Therefore, the purpose of this study is to analyze Busan port and the economic growth of Busan area by researching promising industry, based on the effect of freight transporting by the Northern sea route on the economy of Busan. For this study, questionnaire surveys and interviews were conducted for 64 people of experts in the shipping and port industry, relevant government, and academics. The survey finding shows that port logistics industry is a promising business in Busan in terms of its growth and competitiveness. It is necessary to develop feeder network facilities that prepare for commercialization of the Northern sea route as a short and medium term plan and provide professional manpower training in polar regions. Ship supply business would also play an important role. It is identified that revitalization of shipbuilding and ocean plant industry should be done in terms of Arctic business. With regard to the fishery industry it is found that modernization of fishery ship and development of fishery equipment used in polar areas should be carried out.

• Korean Security Journal
• /
• no.48
• /
• pp.147-176
• /
• 2016

Korean Peninsula is surrounded by ocean on three sides. Because of this geographical quality over 97% of export and import volumes are exchange by sea. Foreign ship and international passenger vessels carries foreign tourist and globalization and internationalization increases this trends. Leisure population grows with national income increase and interest of ocean. And accidents and incidents rates are also increases. Korea Coast Guard's jurisdiction area is 4.5 times bigger than our country. The length of coastline is 14,963km including islands. One patrol vessel is responsible for 24,068km and one coast guard substation is responsible for 94km. Efficient patrol activities can not be provided. This research focus on this problem. Analyze the status and trends of maritime crime and suggest efficient patrol activities. To deal with increasing maritime crime rate this study suggest to use geographical profile method which developed early 1900s in USA. This geographical profile analyse the spatial characteristic and mapping this result. With this result potential crime zone can be predicted. One of the result is hot spot management which gives data about habitual crime zone. In Korea National Police Agency adopt this method in 2008 and apply on patrol and crime prevention activity by analysis of different criteria. Korea National Police Agency analyse the crime rate with crime type, crime zone and potential crime zone, and hourly, regionally criteria. Korea Coast Guard need to adopt this method and apply on maritime to make maritime crime map, which shows type of crime with regional, periodical result. With this geographical profiling we can set a Criminal Point which shows the place where the crime often occurs. The Criminal Points are set with the data of numerous rates such as homicide, robbery, burglary, missing, collision which happened in ocean. Set this crime as the major crime and manage the data more thoroughly. I expect to enhance the reinforcement of marine crime using this Criminal Points. Because this points will give us efficient way to prevent the maritime crime by placing the patrol vessel where they needed most.