• Journal of the Korean Society of Clothing and Textiles
• /
• v.34 no.2
• /
• pp.280-290
• /
• 2010

This study identifies the antecedents of trust in the examination of the effects of the antecedents of trust on trust in apparel manufacturer-contractor relationships. A total of 92 apparel manufactures participated in this study. A factor analysis, Cronbach's alpha coefficient, and multiple regression analysis were conducted for the statistical analysis. Five antecedents of trust were classified: flexibility, opportunistic behavior, communication, specific investment, reputation. Two factors of trust were identified: credibility and benevolence. Flexibility, communication, and reputation of a contractor positively influenced the credibility of an apparel manufacture in a contractor. Flexibility, communication, and specific investment of a contractor positively relate to the benevolence of an apparel manufacture in a contractor. However, the opportunistic behavior of a contractor did not relate to either the credibility of an apparel manufacture or the benevolence in a contractor. The results of this study provide empirical evidence of the impact of flexibility, communication, specific investment, reputation on trust in apparel manufacturer-contractor relationships, and additional insight for selecting contractors that seek to improve trust in apparel manufacturer-contractor relationships.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2009.11a
• /
• pp.121-125
• /
• 2009

The recycling of waste concrete is increasing for the environment protection and the shortage of aggregate according to the large scale construction project in Korea. The more manufacturing high quality recycled aggregate is produced, the more waste concrete powder generated from the manufacture process of recycled aggregate, and the consideration about the recycling of waste concrete powder is need. Waste concrete powder was used for the partial replacement of silica powder, which is a main raw material for the manufacture of autoclave foamed concrete. According to the results of research, the slurry density, flow, compressive strength mainly depend on the replacement ratio of particle size and waste concrete powder. At the SEM analysis, the more high-waste concrete powder was the less there are generated tobermorite. But we conclude that it is possible to replace WCP as silica source in the manufacture of the lightweight foamed concrete.

• Journal of the Korean Society of Costume
• /
• v.60 no.9
• /
• pp.77-94
• /
• 2010

It was the era, from 1876 to 1910, that some dramatic changes, including an influx of foreign dyes and the beginning of the modern dyeing manufacture, happened in Korea. This paper explores what dyes were sold in the market in this period, who was the main seller of the goods, and how the dyers produced their products. A wide range of natural dye stuffs coexisted with the various kinds of aniline dyes, alizarin dye and synthetic indigo in the market. Coloring materials had been sold by hwapi-jeon, a group of official merchants who acquired a privilege of monopoly from the government. However, the dyes were also traded by sang-jeon and yakguk merchants in the nineteenth century. Most of the synthetic dyes sold in Korea were produced in Germany or in Japan later, and imported in large amount by Chinese, Japanese and German merchants. Yet there also existed Korean merchants and peddlers who sold the goods to the local consumers. Dyers were male and female who belonged to the middle class. They received the orders and payments from the government or merchants. Not only did they dye textiles, threads, cotton, paper and leather, but they also redyed clothes. Indigo dyers were differentiated from other dyers. Modern dyeing manufacture, which was presumably forced to keep pace with the productivity of the weaving process, appeared in the 1900s. It was a branch of the modern weaving manufacture.

• Journal of the Korean Academy of Esthetic Dentistry
• /
• v.25 no.1
• /
• pp.50-63
• /
• 2016

Successful treatment in the anterior esthetic prosthetic can be a balance between aesthetics in the facial, tooth, and periodontal tissue in the oral. In the case of facial symmetry of patients with normal occlusal plane, If you establish criteria of finding balance of aesthetics such as a several books and articles and manufacture a prostheses by the established-criteria, you can manufacture a harmonious and aesthetic prostheses without any trouble. However, in the case of patients with facial asymmetry, if you manufacture a tooth as patient's facial aesthetic symmetry by force even facial asymmetry case, you can't get a result not only aesthetic but also functional prostheses. Also, to produce the prosthetic of harmonious and aesthetic with periodontal tissue, and excellent self-cleansing function, you must apply to the form of the prosthetic changed dental environment.

• Journal of the Korean Society of Safety
• /
• v.26 no.5
• /
• pp.65-72
• /
• 2011

The use of waste concrete can resolve the environmental pollution and shortage of natural aggregate. However, recycled aggregate includes substantial amount of cement paste. So, these aggregates are more porous, and less resistant to mechanical actions than natural aggregates. So, recently, the new manufacture processes of high quality recycled aggregates were suggested such as heating and solving to acid liquid. But the method of solving to acid liquid is not economical and produces additional environmental pollution. In this paper, for the purpose of manufacture of high quality recycled aggregates, the heating processes was added to the existing process of recycled aggregates. To find the optimum process, the experiment was performed by using the method of statistical experiment design, and the heating temperatures(4 levels : 300, 450, 600 and $750^{\circ}C$) and heating times(4 levels : 5, 20, 40, 60 minute) were main experimental variables. By the test results, the optimum manufacturing condition of coarse recycled aggregate was $600^{\circ}C$ and 40 minute, and for the fine recycled aggregate, a little heating made a satisfaction to the KS standard quality code.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.42 no.5
• /
• pp.47-53
• /
• 2010

It is important to utilize the citrus sludge in terms of the reuse of waste materials in the manufacture of corrugated medium. Especially, the mandarin industry occupies the first place in Jeju province. In this paper, the application of citrus sludge mixed with KOCC recycled fibers into the manufacture of corrugated medium was studied. The citrus sludge was acidic in pH value. Also, the constituents of citrus sludge contain some short fibers, fines, and mucus which contain flavonoids, pectins and so on. In papermaking application, these components cause some troubles like foams, bad smell, fouling on the paper machine, and bad drainage and web breaks of wet web. The strength properties of handsheets prepared from KOCC and citrus sludge was decreased, compare to handsheets made of only KOCC. To compensate the problems on strength properties, some kinds of additives were tried to apply into papermaking wet-end system in laboratory scale. As a result, mixing conditions of alum, starch and anionic additives showed the best options in the recovery of strength properties and formations of corrugated medium.

• Proceedings of the KSR Conference
• /
• 2008.11b
• /
• pp.1710-1716
• /
• 2008

The Loop Heat Pipe (LHP) operates to pump the working fluid by means of the capillary force in a wick structure. Particularly, it is difficult to design and manufacture the evaporator consisted of a grooved container and a compensation chamber as well as the wick structure. This study is related to design and manufacture the grooved container coupled with wick structure, the properties of the wick structure such as the permeability, the porosity, and the maximum capillary pressure were measured to apply the cooling technology for Insulated Gate Bipolar Transistor (IGBT). The container of the LHP was manufactured by the electrical discharge process and the wick structure was sintered with the nickel particle by an axial-press apparatus with the pulse electronic discharge. As results, the properties of the wick were experimentally obtained about 60% of the porosity, 35kPa of the maximum capillary force and $1.53{\times}10-13m2$ of the permeability.

• The Research Journal of the Costume Culture
• /
• v.27 no.1
• /
• pp.57-63
• /
• 2019

Due principally to the desire to seek lower production costs, the bulk of the world's textile and clothing manufacture migrated to low-cost zones, mainly outside Europe, over the course of the late-twentieth century. In the early-twenty-first century, fast fashion became a dominant force worldwide, with 'Western' retail buyers hunting cheaper deals from clothing manufacturers (mainly in Asia), and with occasional disasters not changing matters beyond the duration of a fashion season. Progressively, seams became narrower, cheaper raw materials were used and durability was no longer an aim. Why bother to do otherwise? This was what the 'Western' consumer wanted: fashion to be worn only a few times and then discarded, despite the fact that vast amounts of human, technological and financial resources were wasted in such a quest. By the end of the second decade of the twenty-first century, the production of textile and clothing products continued to contribute substantially to global warming. This paper reviews briefly the current conditions of manufacture, and argues that the research agenda should be focused on addressing the implications of a progressively changed focus, not on fast-fashion products, but instead on the production of products with greater durability. Meanwhile 'Western' consumers need to turn away from fast fashion and realise that waste is bad for their economy and their society. It is argued further, that after a period of re-adjustment, substantial financial rewards await the national textile and clothing industries that undergo such a turn around.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2020.11a
• /
• pp.12-13
• /
• 2020

Free-form buildings usually have large curved shapes on the outside. In order to construct this curved shape, the exterior of the building must be divided into easy-to-manufacture shapes, and the segmented panel is called the FCP(Free-form Concrete Panel). These FCPs have different shapes and cannot reuse molds. To solve these problems, the researchers developed FCP manufacturing equipment to manufacture a mould of FCP. However, the developed equipment alone cannot completely manufacture FCP's mould. This is because there is no mould to implement side of FCP. Therefore, it is necessary to develop a side form of FCP that can be applied to FCP manufacturing equipment. To this end, this study analyzes the basic requirements that side mould should have before developing side mould.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2023.11a
• /
• pp.21-22
• /
• 2023

In order to manufacture high-quality free-form concrete panel (FCP), it is necessary to analyze the limitations of free-form silicone mold (FSM) and conduct technology development research. Currently, the FSM used in FCP manufacture is classified into a side silicon mold(SSM) and a lower silicon mold(LSM). In this study, the limitations of each silicon mold were analyzed and solutions were proposed. In the case of side silicon mold, there is a limit to cannot supporting the side pressure of concrete. Therefore, a mold stacking method was proposed, and at the same time, a process of correcting the movement value of the rod was proposed. In the case of the lower silicon mold, there is a limit to completely implementing the design shape. Therefore, a real-time scanning method and a process of displaying FCP shape coordinates were proposed. The results of this study are expected to be used as basic data for manufacturing high-quality FCP.