• 한국자동차공학회논문집
• /
• 제5권5호
• /
• pp.73-85
• /
• 1997

An automatic transmission is an important element of automotive power systems that allows a driving convenience. Compared to a manual transmission, however, it has a few problems in efficiency, shift feel, and maintenance. To improve these, it is imperative to understand the dynamics of automatic transmissions. This paper develops a dynamically-correct model of an automatic transmission, using the bond graph method. The bond graph method is ideally suited for modeling power systems, because the method is based on generalized power variables. The bond graph method is capable of providing correct dynamic constraints and kinematic constraints, as well as the governing differential equations of motion. The bond graph method is applied to 1-4 in-gear ranges, as well as various upshifts and downshifts of an automatic transmission, which allows an accurate simulation of an automatic transmission. Conventional automatic transmission models have no dynamic constraint, which do not allow correct simulation studies.

• 한국소음진동공학회논문집
• /
• 제13권2호
• /
• pp.116-125
• /
• 2003

Four models for stick-slip friction are presented and are adopted for a numerical simulation study for a manual transmission clutch damper in idle mode. Meaning of parameters for friction models are explained and proper values are suggested. Also explained ate the reason why those specific values for the parameters are chosen. Preferable model for the clutch damper In Idle mode is discussed in terms of calculation efficiency and fidelity of the model based on real measured data. For clutch damper idle mode simulation studies, all four models perform equally well.

• 한국자동차공학회논문집
• /
• 제12권4호
• /
• pp.146-153
• /
• 2004

This paper presents a discrete analysis approach to investigate the performance of dual mass flywheel (DMF). In the discrete analysis, arcspring installed between the flywheels is modeled as N- discrete elements. Each element consists of mass, spring and nonlinear friction element. LuGre friction model is used to describe nonlinear friction characteristic. Based on the dynamic models of the DMF, clutch, engine, manual transmission and vehicle, a DMF performance simulator is developed using MATLAB Simulink. Simulation results of the engine speed, driveshaft torque and vehicle velocity are compared with test results. It is found that the discrete DMF model describes the vehicle behavior closely, especially during the clutch actuation period.

• 한국자동차공학회논문집
• /
• 제4권4호
• /
• pp.107-117
• /
• 1996

The shift feeling, a driver experiences during gear shifting, is a major factor in manual transmission quality. Recently, the shift feeling has becoming more severe every year in proportion to the higher torque and revolution speed of today's automotive engine. In this paper, first, the diagram of a relation between cone angle, sleeve chamfer angle, and friction coefficient of ring is investigated for easy design of Synchromesh system. And then, methodology to solve the shift problems such as clashing noise and rough shift, ect. by analyzing the synchronization procedure in sequence and by investigating the shift waveform if presented.

• 한국자동차공학회논문집
• /
• 제17권3호
• /
• pp.102-109
• /
• 2009

The stumble (abrupt and big acceleration decrease) occurring in manual transmission vehicle while standing start is analyzed by simulation model. This model was verified by comparing to test results. Mechanism of the stumble is clarified by analyzing simulation results and the key mechanism of the stumble is angular vibration of powertrain including wheel and tires. As a result, several method that can reduce the stumble is proposed by carrying out parametric study, increasing low end torque of engine, increase gear ratio etc.

• 한국자동차공학회논문집
• /
• 제3권2호
• /
• pp.30-41
• /
• 1995

Gear rattle is a source of vibration and noise in automotive gearbox casing and generally occurs at or near system resonant frequencies. The neutral gear rattle of the gearbox. is affected by the stiffness and hysteresis torque in the clutch disk and drag torque determining balancing point of the clutch disk operating range. The experiment is carried out in the pre-damper type clutch and a manual transmission of a automobile equipped for inline four-sylinder four-cycle 1.5L MPI engine and the computer simulation is executed by 5th order Runge-Kutta method. The results of the simulation analysis and experimental studies show the dynamic behavior of clutch and a phenomenon of the neutral gear rattle with respect to drag torque and torsional characteristics of the clutch.

• 한국자동차공학회논문집
• /
• 제21권5호
• /
• pp.1-7
• /
• 2013

The present paper relates to a development of the Gear Detection Sensor for automotive manual transmission. To detect air gap from control finger to detecting zone of sensor based on non-contacted method, permanent magnet and linear type Hall IC are mounted in this sensor. Control finger is machined to 3 step heights to detect 3 gear stages such as In-Gear, Normal and Rear. After conducting actual experimentation based on exclusive Jig and FEM, it is described to consider possibility for automotive application of Gear Detection Sensor.

• 한국지능시스템학회:학술대회논문집
• /
• 한국퍼지및지능시스템학회 2001년도 추계학술대회 학술발표 논문집
• /
• pp.271-274
• /
• 2001

Recently, most vehicles has the Automatic transmission system as their transmission system. The automatic transmission system operates with fixed shift patterns. In the opposite of manual operation, it is easy and convenient for driving. Though these merit, the system can not evaluate the driver's intension because of usage of fixed shift pattern, To consider driver's intension, we must consider both the driving intensity of driver and the status of vehicle. In this paper, we developed flexible automatic transmission system by using the proposed moduled neural networks which can learn the status of the vehicle and driver's intensity As a result, we compare the transmission system using fixed shift pattern and the proposed transmission system and show the good performance in the change of shift position.

• 한국가스학회지
• /
• 제24권6호
• /
• pp.55-60
• /
• 2020

세계적으로 친환경자동차의 연구 및 개발이 확대되면서 주행거리를 증대시키기 위해 차량의 부가적인 장치를 축소·삭제하거나 경량화를 위한 연구를 진행하고 있다. 그 중 내연기관자동차에 적용되던 다단변속기를 삭제하고 감속기로 대체하여 모터출력 값 제어를 통해 토크증대로 초기구동력을 확보하고 있다. 하지만 잦은 모터의 속도변화로 부하가 상승되는 결과를 가져올 수 있기 때문에 본 연구에서는 일반적인 감속기구조를 갖는 소형·경량의 수동 2단 감속기를 개발하려고 한다. 따라서 평행축을 갖는 구조에 대기어와 소기어를 삽입하여 평행한 축의 감속기형태에서 V-벨트로 기어를 연결하고, 저단과 고단의 기어비를 각각 설정하여 2개의 기어비를 갖는 2단 변속기를 설계하였다. 또한 변속기의 회전속도와 부하에 따른 동력성능을 시험을 통해 확인하고 구동시 발생되는 발열특성을 확인하여 변속기의 타당성을 검증하였다.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2008년도 추계학술대회논문집
• /
• pp.105-111
• /
• 2008

The clutch with torsional damper is installed on a passenger car with manual transmission, which not only transmits the power generated by engine to the transmission but also absorbs the shock and vibration from the engine. The torsional damper in the clutch dissipates the torsional vibration energy and eliminates the resonance in the driveline but high damping in the damper causes the increase of the vibration level which is against the comfort and durability. In this study, a dynamic model for the passenger car driveline with manual transmission was developed to investigate the vibration and the effects of characteristics of the driveline. With the dynamic model, the vibration characteristics of driveline were examined by the mode analysis and driving simulation, and the effects of hysteresis torque and spring constant were investigated. The vehicle tests with prototype torsional dampers were preformed and the test results showed good agreements with the simulation.