• Journal of Institute of Control, Robotics and Systems
• /
• v.12 no.9
• /
• pp.850-855
• /
• 2006

This is concerned with the development and design of automatic maneuvering system using Differential Global Positioning System(DGPS). To achievement of autonomous maneuvering controller for giant ship, first, we investigated automatic maneuvering controller using DGPS in motor car. The sensors are configured with DGPS and digital compass. We calculated velocity and steering angle of motor car based on sensor signal. To design the controller, we derived the bicycle model and developed critically damped controller. The critically damped controller can be tracing previously appointed position in the fastest time. We are used a laptop computer to realize and the control algorithm is programmed by visual basic software. The obtained experimental results from developed system show unmanned motor car is good tracing planed positions. Hence, the system is looking forward to use the autonomous maneuvering control fur giant ship.

• 제어로봇시스템학회:학술대회논문집
• /
• 2003.10a
• /
• pp.728-733
• /
• 2003

In human-mechanical cooperative systems, a significant issue is to improve the control performance and the maneuvering feeling of human operation. However, since it is not easy to evaluate the feeling of operators numerically, control engineers design controllers only through experience. Thus, in this paper, a new evaluation method for control performance of human-mechanical cooperative system is proposed based on the reserge waveform. Various distortions of waveform represent deteriorations of control performance and maneuvering feeling. In some cases, since there is a tradeoff between the control performance and the maneuvering feeling, it is difficult to compensate for both of them by usual feedback controllers. To overcome this situation, the two degrees of freedom control system is applied to human-mechanical cooperative system. Some numerical simulation results for an electric power steering system are shown to confirm the effectiveness of proposed control design method.

• Nuclear Engineering and Technology
• /
• v.42 no.3
• /
• pp.329-338
• /
• 2010

We developed an achievable control logic for the reactor power level during a power maneuvering event and set up some constraints for the control of the reactor power in a conceptual sodium-cooled fast reactor (KALIMER-600) that was developed at KAERI. For simulating the dynamic behaviors of the plant, we developed a fast-running performance analysis code. Through various simulations of the power maneuvering event, we evaluated some suggested control logic for the reactor power and found an achievable control logic. The objective of the control logic is to search for the position of the control rods that would keep the average temperature of the primary pool constant and, concurrently, minimize the power deviation between the reactor and the BOP cycle during the power maneuvering. In addition, the flow rates of the primary pool and the intermediate loop should be changed according to the power level in order to not violate the constraints set up in this study. Also, we evaluated some movement speeds of the control rods and found that a fast movement of the control rods might cause the power to fluctuate during the power maneuvering event. We suggested a reasonable movement speed of the control rods for the developed control logic.

• Journal of the Korea Institute of Military Science and Technology
• /
• v.16 no.3
• /
• pp.240-249
• /
• 2013

This paper discusses the maneuvering control algorithm based on all-wheel independent driving and steering control techniques for special purpose 6WD/WS vehicles. The maneuvering control algorithms considering superior dynamic characteristics of high power in-wheel motors and independent steering system are designed to perform driving, steering, vehicle stability, and fault tolerant control. The maneuvering controller applies sliding and optimal control theories considering optimal torque distribution and friction circle related to the vertical tire force. The fault tolerant control algorithm is applied to obtain the similar maneuverability to that of the non-faulty vehicle. The simulations using the Matlab/Simulink dynamics model and experiments using HIL simulator mounting the real controllers with the designed control algorithms prove the improved performances in terms of vehicle stability and maneuverability.

• International Journal of Control, Automation, and Systems
• /
• v.5 no.4
• /
• pp.456-462
• /
• 2007

Tracking error performance is investigated for the typical maneuvering pattern of the anti-ship missile for tracking filters based on IMM filter in both clear and cluttered environments. Threatening targets to a navel vessel can be categorized into having three kinds of maneuvering patterns such as Waver, Pop-Up, and High-Diver maneuvers, which are classified according to launching platform or acceleration input to be applied. In this paper, the tracking errors for three kinds of maneuvering targets are represented and are investigated through simulation results. Studying estimation errors for each maneuvering target allows us to have insight into the most threatening maneuvering pattern and to construct the test maneuvering scenario for radar system validation.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2012.04a
• /
• pp.701-706
• /
• 2012

This research is concerned with the derivation of equations of motion for a slewing beam and the application of input shaper to the bang-bang control to achieve vibration suppression. When a uniform beam with a tip mass rotates about the axis perpendicular to the undeformed beam's longitudinal axis, it experiences inertial loading. Hence, the beam vibrates. In this paper, we used the input shaper for the maneuvering control to suppress vibrations. The maneuvering control which can achieve a minimum-time control is a bang-bang control. The input-shaped bang-bang maneuvering is used to suppress vibrations both theoretically and experimentally. The slewing beam experiment is not an easy subject because of the inherent damping existing inside the rotor. We propose the use of a negative damping to eliminate the rotor damping. Numerical and experimental results show that the input-shaper can be effectively used for the vibration suppression of a slewing beam.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.22 no.6
• /
• pp.542-549
• /
• 2012

This research is concerned with the derivation of equations of motion for a slewing beam and the application of input shaper to the bang-bang control to achieve vibration suppression. When a uniform beam with a tip mass rotates about the axis perpendicular to the undeformed beam's longitudinal axis, it experiences inertial loading. Hence, the beam vibrates. In this paper, we used the input shaper for the maneuvering control to suppress vibrations. The maneuvering control which can achieve a minimum-time control is a bang-bang control. The input-shaped bang-bang maneuvering is used to suppress vibrations both theoretically and experimentally. The slewing beam experiment is not an easy subject because of the inherent damping existing inside the rotor. We propose the use of a negative damping to eliminate the rotor damping. Numerical and experimental results show that the input-shaper can be effectively used for the vibration suppression of a slewing beam.

• Proceedings of the Korean Institute of Navigation and Port Research Conference
• /
• 1998.04a
• /
• pp.101-110
• /
• 1998

The safe passing maneuver of a large vessel along the designed course through a narrow channel in the flow of strong current is greatly related with her maneuvering characteristics. This paper treats maneuvering characteristic of a large vessel changing her course with the use of her control surface in a narrow channel with strong current. In this paper, the author proposed mathematical models of calculating maneuvering motions of the very large LNG tanker altering course using her control surface and calculated passing tracks of the vessel through the channel and compared the calculated results with those of maneuvering simulations by a desk-top simulator. In general the motions with the calculated values and the simulated motions are well coincided with each other.

• 제어로봇시스템학회:학술대회논문집
• /
• 2000.10a
• /
• pp.152-152
• /
• 2000

In this paper, we propose a new approach to intelligent motion and autonomous maneuvering of mobile robots using hybrid system. In high Level, the discrete states are defined by using the sensor-based search windows and the reference motions of a mobile robot as a low vevel are specified in the abstracted motions, The mobile robots can perform both the motion planning and autonomous maneuvering with obstacle avoidance in indoor navigation problem. Simulation and experimental results show that hybrid system approach is an effective method for the autonomous maneuvering in indoor environments.

• Journal of the Korean Institute of Navigation
• /
• v.20 no.2
• /
• pp.1-13
• /
• 1996

Most of the ShipHandling Simulators of full-mission-bridge system need vast area to install and even PC-based maneuvering simulators are often equipped with Steering Wheel or Engine Telegraphe etc. of data input interface, which necessarily makes the user face with excessive financial burden. These have been one of the obstacles for the officers, captains, pilots and students in access to maneuvering simulation whenever they want to try it in advance prior to actual ship maneuvering. Subsequently, all the officers and captains come to have little chances to train themselves until they arualified as a pilot after a long period of time of realship maneuvering practice on board, which means they have to control they have to control their own ship at sea without clear understanding on her maneuverability when they are forced to do it on the way. And these lack of capability for maneuvering have used so often to result in marine casualties of collision with other ships or pier facilities while maneuvering in harbor. To prevent those accidents by means of enhancing their maneuvering ability, PC-based DeskTop Simulator that allows anyong to access readily at anytime is needed and in conformation to such demand this simulator has been developed. The Software this simulator written in Turbo Pascal Ver. 5.0 has adopted MMG mathmatical model theoretically in part and also it was designed to make it possible that all numeric data inputs and outputs with graphic presentation for maneuvering operation be carried out just only with keyboard and monitor console. With the Simulation software, all the officers, captains, pilots and even students who has a proper computer at hand are expected to be able to make an attempt to simulate the maneuvering of their ownship or any other types of them at any port in which they want to do it.