• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1996.05a
• /
• pp.99-101
• /
• 1996

This paper is concerned with the fabrication of (Fe,Co)-Si-B amorphous magneto-strictive wire which attracts strong attention as a new sensor material. First, we put the ingot of (Fe$\sub$1-x/Co$\sub$x/)$\sub$77/Si$\sub$8/B$\sub$15/ composition into quartz tube. Then, under the condition of 400MHz and 8kW, we melt and mix the in-got in the high frequency induction furnance. After that, we obtain the magnetostrictive wire of 100∼150$\mu\textrm{m}$ in diameter by injection and rapid quenching within the high rotating water. Finally, we find that the wire is under the amorphous state.

• Journal of Power System Engineering
• /
• v.14 no.3
• /
• pp.46-51
• /
• 2010

A torsional guided wave was applied to detect a defect in petrochemical pipes. Phase and group velocity dispersion curves for the longitudinal and torsional modes of the inspected pipe were presented for the theoretical analysis. It was found through mode shape analysis that there was mode conversion when torsional wave is incident at an asymmetric defect. An artificial notch was fabricated in the pipe and the detectability was examined from the distance 2m of the end of the pipe by using magnetostrictive sensors. The relativities between the amplitude of the reflected signal and the size of the defect was examined. It was shown that the T(0,1) mode could be used for the long range inspection for the petrochemical pipes.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.20 no.9
• /
• pp.841-848
• /
• 2010

Previous experimental results show that the magnetostrictive transducer has the peculiar characteristic with relation to their reversible magnetization and its practical usage will be hindered by this phenomena. In this paper, the idea of anhysteretization is adopted in order to solve this problem. The experimental results reveal that the anhysteretization can get rid of the extraordinary phenomena which are occurred by the change of biasing magnetic field. The effects of two important parameters, which are the amplitude and the decaying time of this process, on the anhysteretization are investigated experimentally. Finally the best operating condition is proposed in order to maximize the sensitivity under the anhysteretization.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2007.11a
• /
• pp.336-339
• /
• 2007

A sensor having capability to measure two different kinds of ultrasonic waves selectively is described. Under the same bias field configuration, this magnetostrictive type sensor can selectively measure longitudinal waves and flexural ones. Since the switching operation of mode selection is made only by changing the polarity of the permanent magnets used to configure the bias field, it will be very useful after the permanent magnet are interchanged with electromagnets. In order to find the optimal operating bias field, finite elements analysis is used and the condition for flexural wave measurements to meet is found. The linearity of the sensor is verified by experiments and the requirements for linearity also are proposed.

• Journal of the Korea Safety Management & Science
• /
• v.2 no.1
• /
• pp.89-97
• /
• 2000

This paper shows the study for development inprocess measuring magnetic sensor for tolerance control, First, we fabricated and annealed sample amorphous ribbons which were made of ($CO_{0.94}$$Fe_{0.06}$)$_{79}$$Si_{2}$$b_{19}$ having near zero magnetostrictive. It had 12［$\mu\textrm{m}$］ of thickness, 10［mm］ of length, and 2.5［mm］ of width. Then, we measured the magnetic characteristics such as frequency dependency over impedance variation rate and position change over impedance variation. As the results of the evaluation, we found that the sample ribbons had excellent sensor characteristics. Then, we made sensors by using the sample ribbons, As the results of the measurements, it proved that the ribbon could be used as excellent magnetic sensor for which it was possible to control inprocess measurement within the tolerance range(~$\mu\textrm{m}$ ).

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2003.03a
• /
• pp.34-34
• /
• 2003

Piezoelectric or magnetostrictive materials, known as smart materials, have been researched widely for sensors or actuators in micro system technology. In our research, thick sol-gel lead zirconate titanate(Pb(Zr$\sub$1-x/Ti$\sub$x/)O$_3$) films were fabricated and their characteristics were investigated f3r angular rate sensor applications. The thickness of the PZT films is 1.5${\mu}$m, which is required by a vibration angular rate sensor for a good actuation and sensing. The remnant polarization of the PZT flms is 12.0 ${\mu}$C/$\textrm{cm}^2$. The electromechanical constants of PZT thin film showed the value of susceptance(B) of 4800${\mu}$ s at capacitance of 790pF. The PZT films were applied to the vibration angular rate sensor structure and the vibration of 1.78 ${\mu}$m in amplitude at the resonant frequency of 35.8㎑ was obtained by driving voltage of 5V$\sub$p-p/ of bulk piezoelectric materials with out of phase signal through voltage and inverting amplifier.

• Journal of Magnetics
• /
• v.9 no.2
• /
• pp.47-51
• /
• 2004

Giant magneto-impedance (GMI) effect in zero-magnetostrictive Co-based amorphous ribbons samples in their as-quenched and stress-released states as well as with intentionally induced magnetic anisotropy were investigated. Magnetic and impedance properties of the samples exhibiting different anisotropy were compared and the optimum operation conditions for the studied samples from the view-point of their utilization as a sensor element have been determined. A design of a model of magnetic field sensor and characteristics of the constructed prototype are presented.

• Journal of Magnetics
• /
• v.8 no.1
• /
• pp.60-69
• /
• 2003

A review of mechanical sensing techniques based on magnetic methods is presented, with special reference to magnetoelastic strain gauges and force sensors. A novel strain sensor based on soft amorphous ribbons is described. Other types of magnetic sensors, for the measurement of torque and displacement are briefly discussed. An overview of magnetic actuators based on giant magnetostrictive materials, with some practical examples, is presented. Recent advances in the development and application of magnetic shape memory materials are discussed, together with the analysis of recent studies for the description of magnetic shape memory phenomena.

• Journal of the Korean Magnetics Society
• /
• v.13 no.5
• /
• pp.193-197
• /
• 2003

To materialize the magnetoelastic devices, such as a highly functional sensor and a signal processing device, using the Fe base amorphous film which has both excellent soft magnetic and magnetostrictive properties, in this study, a new method to control the magnetic anisotropy of a highly magnetostrictive film using bias stress has been proposed and tested. The film pattern, which was stressed by its substrate bending, was subjected to annealing for relieving its stress. Successively, the compressive stress occurred by flattening the substrate was formed in the pattern. With the introduction of the residual compressive stress, the magnetization of the film pattern was aligned in the transverse direction through magnetoelasic coupling. The magnetic domain structure and magnetization curve of the film pattern of which magnetic anisotropy was controlled by the proposed method were presented to verify the availability of the method.

• Journal of Sensor Science and Technology
• /
• v.12 no.2
• /
• pp.95-101
• /
• 2003

Ultrasonic transmitter used for scale prevention in boiler or heat exchanger is composed of the magnetostrictive material which transforms electric energy into ultrasonic wave and the horn which amplifies generated ultrasonic wave and transfers it into medium loaded. In this paper, we have performed the shape design for magnetostrictive material and analyzed a few type of horns which amplify generated ultrasonic wave and found each solution theoretically. Final length of the horn has been determined by measuring the sound pressure in medium between theoretical value and experience data. At last we have given the results of our study for the effects of ultrasonic wave irradiated by manufactured ultrasonic transmitter on preventing scale deposition on test pipe under the similar condition to boiler.