• 대한기계학회논문집A
• /
• 제21권9호
• /
• pp.1392-1399
• /
• 1997

In order to determine the Mode I stress intensity factor ($K_1$) experimentally by means of the alternating current potential drop(ACPD) technique, the change in potential drop due to load for a ferromagnetic material containing a two-dimensional surface crack was examined. The cause of the change in potential drop and the effect of the magnetic flux on the change in potential drop were clarified by using the measuring systems with and without removing the magnetic flux from the circumference of the specimen. To remove the magnetic flux, a new measuring system was made by utilizing the characteristic of coaxial transmission line. The change in potential drop in the case without magnetic flux in the air was caused by the change in electromagnetic properties near the crack tip due to magnetization. The relationship between the change in potential drop and the change in $K_I$ was linealized by demagnetization and was found to be independent of the crack length.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2000년도 하계학술대회 논문집 B
• /
• pp.822-824
• /
• 2000

To apply HTS to AC devices, it is necessary that study theoretically and experimentally to analyze the AC losses. It should be investigated the theoretical mechanisms precede the actual experiments. Because the AC losses cause some complicated troubles in AC machines, we can design the machines properly. In this study, firstly we analyze the basic cause of AC losses by investigating the several loss factors, secondly measure the AC losses of HTS by using Magnetization. Technique and this results show that AC losses of HTS is tenuous than those of general materials used in power system. Consequently we can compare the actual results with the theoretical results. And we find that AC losses of HTS are related to the amplitude of external magnetic field and the frequency. Through this study, we find that it is possible to apply the results by Magnetization. Technique to the AC power system, to the design of AC machine, to design of HTS proper to the foretold AC losses.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2006년도 춘계학술대회 논문집 전기기기 및 에너지변환시스템부문
• /
• pp.140-142
• /
• 2006

Cogging torque is often a principal source of vibration, noise and difficulty of control in permanent-magnet brushless DC motors. Cogging torque can be minimized by sinusoidal air-gap flux density waveform because it is produced by the interaction of the rotor magnetic flux and angular variation in the stator magnetic reluctance. Therefore, this paper will present a design method of magnetization system of bonded isotropic neodynium-iron-boron(Nd-Fe-B) magnets in ring type with sinusoidal air-gap flux density distribution and low manufacturing cost. An analytical technique of magnetization makes use of two-dimensional finite element method(2D FEM) and Preisach model that expresses the hysteresis phenomenon of magnetic materials in order for accurate calculation.

• 전기학회논문지
• /
• 제56권3호
• /
• pp.506-513
• /
• 2007

This paper proposes a rotary magnetic position sensor which has a sinusoidally magnetized permanent magnet with a small number of poles. To make the sinusoidal magnetic flux density distribution from the permanent magnet, a magnetizing future is optimized by the DOE(Design of Experiments) method. The magnetization process is analyzed using the Preisach model and 2 dimensional finite element method. The magnetic flux density distribution from the magnetized permanent magnet is very similar to ideal sine wave. The simulation result of the magnetic flux density distribution is compared with the experimental one. Also the availability of the proposed rotary type magnetic position sensor is confirmed by position calculation technique.

• 대한전기학회논문지:전기물성ㆍ응용부문C
• /
• 제48권1호
• /
• pp.29-33
• /
• 1999

Superconducting tape is being developed for electrical equipment such as superconducting transformers and generators etc. AC loss reduction is primary concerned in the development of such high-efficiency equipment. AC losses in Bi-2223 silver-sheathed tapes, both single and multi-filamentary, were investigated by means of AC magnetization techniques when longitudinal fields are applied. The experiment resultswere compared with the hysteresis loss equation based on Bean model and the eddy current loss equation. The AC loss of the mono-filamentary tape was dominated by the hysteresis. On the contrary, the AC loss of the multi-filamentary tape was substantially dominated by the eddy current loss in the silver matrix.

• Journal of Magnetics
• /
• 제2권2호
• /
• pp.38-41
• /
• 1997

Spinel ferrite thin films Fe3-x MnxO4 (x=0.000, 0.006, 0.0010, 0.015, 0.023) were prepared on the coverglass by ferrite plating technique. To investigate the uniaxial anisotrpy of the samples, the saturation and effective magnetization of the thin films were measured by VSM(vibrating sample magnetometer) and FMR(ferromagnetic resonance) measurements respectively. The spectroscopic splitting g factor were estimated from the ferromagnetic resonance curves. For x=0.000, 0.006, the effective magnetization was measured of temperatures form T=77 K to T=300 K. The results were analyzed in terms of Bloch's law Ms(T) = Ms(0) (1-BT3/2-CT5/2). The Bloch coefficient B, C were determined by fitting. Ms(0) was obtained by extrapolating Meff to 0 K. From this result, the spin wave stiffness constants D was also determined.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 1998년도 춘계학술대회 논문집
• /
• pp.49-52
• /
• 1998

Preparation of hexagonal strontium-ferrite by modified spray co-roasting(MSC:H) which is expected to shorkn the length of the process and to elevate the magnetic properties of hard ferrite was studied. We prapared $Fe_2O_3/SrCO_3$ mixture powders by MSCR after stirring ionized $FeCI_2$ in distilled water with solid state $SrCO_3$. And then calcined the mixture powders up to $1150^{\circ}C$ for Sr-ferrite powders It is possible to prepare hexaferrite powders with high saturation magnetization (Ms > 69 emu/g) , coercivity (Hc > 4000 Oe) The nlagnetic values of saturation magnetization iire higher than those achieved by the conventional technique.

• Korean Journal of Radiology
• /
• 제1권1호
• /
• pp.11-18
• /
• 2000

Objective: To evaluate the hydrodynamic changes occurring in cerebrospinal fluid (CSF) flow in cervical spinal stenosis using the spatial modulation of magnetization (SPAMM) technique. Materials and Methods: Using the SPAMM technique, 44 patients with cervical spinal stenosis and ten healthy volunteers were investigated. The degree of cervical spinal stenosis was rated as low-, intermediate-, or high-grade. Low-grade stenosis was defined as involving no effacement of the subarachnoid space, intermediate-grade as involving effacement of this space, and high-grade as involving effacement of this space, together with compressive myelopathy. The patterns of SPAMM stripes and CSF velocity were evaluated and compared between each type of spinal stenosis and normal spine. Results: Low-grade stenosis (n = 23) revealed displacement or discontinuity of stripes, while intermediate- (n = 10) and high-grade (n = 11) showed a continuous straight band at the stenotic segment. Among low-grade cases, 12 showed wave separation during the systolic phase. Peak systolic CSF velocity at C4-5 level in these cases was lower than in volunteers (p < .05), but jet-like CSF propulsion was maintained. Among intermediate-grade cases, peak systolic velocity at C1-2 level was lower than in the volunteer group, but the difference was not significant (p > .05). In high-grade stenosis, both diastolic and systolic velocities were significantly lower (p < .05). Conclusion: Various hydrodynamic changes occurring in CSF flow in cervical spinal stenosis were demonstrated by the SPAMM technique, and this may be a useful method for evaluating CSF hydrodynamic change in cervical spinal stenosis.

• 지구물리
• /
• 제2권2호
• /
• pp.135-142
• /
• 1999

선형 자기쌍극자 모델의 하나인 철근에 대하여 3성분 자력계를 이용한 자력검층을 실시한 후 검층자료를 최소 자승법에 의한 역산을 이용하여 해석하였다. 본 실험에 사용된 철근의 길이는 1.12 m, 샘플링 간격은 0.05 m, 자력계와 철근사이의 거리는 0.3 m이며, 철근의 상단부를 깊이 0 m 지점에 고정하였다. 철근은 연직에 가깝도록 위치시켰다. FFT를 이용하여 평활화한 자기이상을 역산의 입력자료로 활용하였다. 검층자료의 해석을 위하여 선형 자기쌍극자의 상단부 심도, 길이, 단위 길이 당 자기모멘트, 자화방향(편각 및 복각), 경사방향과 경사각 등을 미지수로 설정하였다. 자기이상의 수평성분 및 수직성분 각각에 대한 역산 결과와 수평성분과 수직성분을 동시에 고려한 역산 결과를 비교하였는데 각각의 역산결과는 다소 차이를 보인다. 자기이상의 수평성분과 수직성분을 동시에 고려하여 역산을 수행하는 것이 각각의 성분을 역산하는 경우보다 정확한 해석이 가능한 것으로 판단된다. 이 때 철근 하단부의 추정 심도는 1.18 m로, 실제 심도인 1.12 m에 매우 근접하며, 철근의 복각은 -76°로 추정되었다. 철근의 복각이 음(-)의 값을 갖는 것은 철근의 유도자화 강도에 비하여 잔류자화 강도가 훨씬 커서, 전체적인 자화 방향이 철근의 상단 방향을 향하고 있기 때문으로 해석된다.

• 전기학회논문지P
• /
• 제58권4호
• /
• pp.535-537
• /
• 2009

As a kind of high Tc superconductor application technique, a study on the development of energy storage device system using BiPbSrCaCuO superconductor was performed. Chemical melt process was developed to gabricate the high magnetization superconductor which is needed to develop the energy saving system and the effect of various process variable on the superconducting properties of the specimens were tested and analyzed. Magnetochemical interactions between superconductor and permanent magnet was also experimented.