• 한국분말야금학회:학술대회논문집
• /
• 한국분말야금학회 2006년도 Extended Abstracts of 2006 POWDER METALLURGY World Congress Part2
• /
• pp.1177-1178
• /
• 2006

Magnetic Properties of dust cores made of mixtures of atomized pure iron powder and pure alumina powder has been investigated in the temperature range from 673 to 1073K. The effect of annealing on coercivity has been positive effect up to 973K and thus coercivity is gradually reduced form 280A/m (as-compressed) to 160A/m (973K). However, dust cores annealed at 1073K displayed a 15% increasing of coercivity by annealing at 973K. Hysteresis loss shows a tendency similar to coercivity. Microstructure observation of specimens shows grain refinement by recrystallization in the temperature range from 773 to 1073K.

• Journal of Magnetics
• /
• 제22권1호
• /
• pp.7-13
• /
• 2017

The magnetoresistance (MR) properties of antiferromagnetic (AFM) IrMn based giant magnetoresistance-spin valve (GMR-SV) was investigated in view point of the artificial rotation effect of ferromagnetic (FM) layer in the plane induced by an applied field during the post annealing temperature. The MR curves measured with an azimuthal angle region of ${\phi}=0^{\circ}-360^{\circ}$ are depended on the annealing temperature and the magnetization easy axis of two free NiFe layers and two pinned NiFe layers in dual-type GMR-SV film. Especially, the annealing temperature and sample rotation angle(${\theta}$ ) maintained to the magnetic sensitivity (MS) of 1.4 %/Oe with an isotropic region angle of $110^{\circ}$ are $100^{\circ}C$ and $90^{\circ}$, respectively.

• 한국재료학회지
• /
• 제13권7호
• /
• pp.447-452
• /
• 2003

Effects of annealing and thickness of Co layer in Co/IrMn bilayers on the magnetic properties have been investigated. The highest interfacial exchange coupling energy($J_{K}$ = 0.12 erg/$\textrm{cm}^2$) was obtained for 10 nm Co layer thickness. Exchange bias field is inversely proportional to the magnetization, the thickness of the pinned layer, and the grain size of antiferromagnetic layer. Also it is related to the interfacial exchange energy difference, which is expected to depend on the surface roughness. These results almost agree with the random-field model of exchange anisotropy proposed by Malozemoff. Exchange bias field decreased slowly with increasing annealing temperature up to X$300^{\circ}C$. However, exchange bias field increased above $300^{\circ}C$.

• Journal of Magnetics
• /
• 제16권2호
• /
• pp.177-180
• /
• 2011

0.30 mm thick and 90 mm wide thin foils made of Fe-6.5wt.%Si alloy were successfully fabricated by traditional rolling. The as-rolled sheets had good shapes and shining metal luster. The effects of annealing temperature on the magnetic properties of the sheets were investigated. Excellent Dc properties ($H_c$: 11.55 A/m, ${\mu}_m$: 23710, and $B_s$: 1.439 T) were obtained at an annealing temperature of 1453 K for 1.5 h. At low frequencies ($\leq$ 1 kHz), heat treatment temperature has little effect on iron loss which remained at the level of 9.8 W/kg. Annealing at 1273 K for 1.5 h is optimum for frequencies above 5 kHz.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2006년도 하계학술대회 논문집 Vol.7
• /
• pp.311-312
• /
• 2006

The dielectric Properties of add $Li_2CO_3$ to ($Ba_{0.6}Sr_{0.4})TiO_3$ powder in this research, made thick film by tape casting method and annealing at $970^{\circ}C$ for 2 hours each from the $O_2$, Ar and O2-plasma atmosphere were investigated. The dielectric Properties of Ar atmosphere was to higher with tunability. The dielectric constant was increased and Curie temperature was shifted to higher temperature with increasing of annealing temperature.

• 센서학회지
• /
• 제16권5호
• /
• pp.389-393
• /
• 2007

Soft ferromagnetic materials are very useful for many sensors using magnetic materials demanding high permeability, low coercivity and low hysteresis loss. Among them, FeCoSiBNi amorphous magnetic films show a good impedance change (about 5.01 %/Oe, at 10 MHz) by the exterinal magnetic field in this experiment. The magnetic films are produced by melt-spun method, one of the rapid solidification process. Ribbon shape wires were made from the films, and let them annealed in DC magnetic field to increase the maximum Giant Magneto Impedance ratio. Field annealing decreases the stress and changes the effective anisotropy. Thus, we can find that the impedance change (200.47 %) is improved and the fabricated magnetic wire has characteristics of good sensor element.

• 한국진공학회지
• /
• 제12권S1호
• /
• pp.17-20
• /
• 2003

We have studied magnetic and structural properties of ultrathin Ni films grown on PI(lII) surface using in situ surface magneto-optic Kerr effect and X-ray photoelectron spectroscopy. Perpendicular magnetic anisotropy was absent, and longitudinal Kerr signal was only detectable for Ni films thicker than 6 monolayers. Enhancement in longitudinal Kerr signal by 30% was achieved by post-annealing at temperatures below 800K, but upon annealing at 820K, surface alloy was formed. By using core-level binding-energy shifts, the composition was determined to be Ni 70 at. %.

• 한국생산제조학회지
• /
• 제20권2호
• /
• pp.174-179
• /
• 2011

This paper focuses on the optimal step-over value for magnetic tool path. Since magnetic flux density is changed according to distance from center of magnetic tool. Enhanced surface roughness is also different according to change of radius. Therefore, to get a identical surface roughness on workpiece, it is necessary to find optimal tool path including step-over. In this study, response surface models for surface roughness according to change of radiuses were developed, and then optimal enhanced surface roughness for each radius was selected using genetic algorithm and simulated annealing to investigate relation between radius and surface roughness. As a result, it found that step-over value of 6.6mm is suitable for MAP of magnesium alloy.

• 한국분말재료학회지
• /
• 제3권1호
• /
• pp.13-24
• /
• 1996

Two grades of Permalloy strips, Fe-45Ni(PB) and Fe-78Ni-4Mo-5Cu(PC) were fabricated by powder rolling process from elemental powder mixtures. The roll compacted green strips were sintered, homogenized, cold rolled with or without an intermediate annealing and finally heat treated to measure magnetic properties. For a given thickness reduction, rolling with an intermediate annealing was found more effective to achieve a full densification with no visible micropores and also to obtain better magnetic properties. Increasing the final rolling reduction also produced a marked improvement of the magnetic properties whereas the cooling rate during the final heat treatment has little effect in both grades. Addition of a small amount, 0.4% Mn slightly degraded the properties. As an overall, The PM strips produced via powder rolling yielded the similar soft magnetic properties to the corresponding commercial grades produced via wrought processing.

• 대한금속재료학회지
• /
• 제50권3호
• /
• pp.248-255
• /
• 2012

AlN thin films containing various amounts of Co, AlN-Co, and Al-Co alloy particles were prepared using a two-facing-target type dc reactive sputtering (TFTS) system. The as-deposited films exhibited the variable nature expected from an AlN-rich phase, and an amorphous-like phase, depending on the Co content in the films. Specific favorable microstructures were prepared by optimizing annealing conditions. Those microstructures and their magnetic properties and resistivity were investigated. As-deposited films showed very small saturation magnetization and an amorphous-like structure. However, when annealed, the as-deposited amorphous-like phase decomposes into phases of AlN, Co and Al-Co. These annealing induced changes in the microstructure improve the magnetization and resistivity of the films. Further improvement of soft magnetic properties could lead to the material being used for high density magnetic recording head material.