• 한국자동차공학회논문집
• /
• 제21권4호
• /
• pp.77-82
• /
• 2013

In this paper, the design of experiment with two-way factorial design was adopted and from that, optimum values of welding variables including the welding speed and rotation speed were found to improve the strength of AZ31 magnesium alloy sheets joined by the friction stir technique. Tool with shoulder diameter of 12 mm and pin diameter of 3.5 mm was used. Also the welding direction was aligned with the material rolling direction, and dimensions of the AZ31 magnesium alloy sheets were $100{\times}100{\times}2mm$. Conditions of rotation speed were 1000, 1100 and 1200 rpm and those of welding speed were 200, 300 and 400 mm/min. As far as this work is concerned, the optimal conditions for friction stir joint were predicted as the rotation speed of 1200 rpm and welding speed of 200 mm/min.

• 동력기계공학회지
• /
• 제15권1호
• /
• pp.39-44
• /
• 2011

This study was to investigate the effects of stress ratio and anisotropy on Fatigue Crack Propagation(FCP) behavior of rolled magnesium alloy AZ31B. The experimental materials were a Mg-Al-Zn magnesium alloy. The FCP test was conducted on compact tension specimen by a servo-hydraulic fatigue testing machine in air at room temperature. Compact tension specimens were prepared from the extruded parallel and vertical rolling direction. The test condition was frequency of 10Hz and sinusoidal load stress ratios are 0.1 and 0.7. The FCP rates was automatically measured by a compliance method. In the case of the FCP of AZ31B, the FCP of both direction of LT and TL by anisotropy of specimens are almost same value. In lower stress ratio, the FCP of the LT, TL specimens are increased in lower ${\Delta}K$ region but higher ${\Delta}K$ regions are almost same value. Finally, the result of observed the surface crack, it expressed the quasi-cleavage fracture in lower ${\Delta}K$ region and straight mark on the aspect of the facet in high ${\Delta}K$ region.

• 한국안전학회지
• /
• 제31권2호
• /
• pp.83-89
• /
• 2016

As the world's industrial development quickens, the highways and regional expressways have been expanding to serve the logistics and transportation needs of people. The burgeoning road construction has led to a growing interest in roadside installations. These must have reliable performance over long periods, reduced maintenance and high durability. Steel roadside barriers are prone to corrosion and other compromises to their functionality. Therefore, using high anti-corrosion steel material is now seen as a viable solution to this problem. Thus, the objective of this paper is to expand the scope of applications for high anti-corrosion steel material for roadside barriers. This paper assesses the impact safety such as structural performance, occupant protection performance and post-impact vehicular response performance by a simulation review on roadside barriers built with high strength anti-corrosion steel materials named as hot-dip zinc-aluminium-magnesium alloy-coated steel. The simulation test results for the roadside barriers built with high strength anti-corrosion steels with reduced sectional thickness meet the safety evaluation criteria, hence the proposed roadside barrier made by high strength and high anti-corrosion hot-dip zinc-aluminium-magnesium alloy-coated steel will be a good solution to serve safe impact performance as well as save maintenance cost.

• 한국기계가공학회지
• /
• 제2권2호
• /
• pp.84-90
• /
• 2003

Magnesium alloys have been paid attention In automotive and industries as lightweight materials, and with these materials it has been attempted at deep drawing process for assessment of formability of sheet metal. For warm deep drawing process with a local heating and cooling technique, both die and blank holder were heated at warm temperature while the punch was kept at room temperature by cooling water. Warm deep-drawing process with considering heat transfer was simulated by finite element method to investigate the improvement of deep-drawability and temperature distribution of Mg alloy sheet. The effect of sham rate sensitivity index on the deformation profile was considered in this work and the simulation results revealed that considering heat transfer is very effective for deep-drawability of Mg alloy. The deformed blank In considering heat transfer was drawn successfully without any localized thinning and the cup height is higher in contrast to results of simulations in considering no heat transfer.

• Journal of Welding and Joining
• /
• 제30권5호
• /
• pp.70-75
• /
• 2012

This study is related to the laser weldability of AZ31B magnesium alloy, an all-purpose wrought alloy with good strength and ductility. In general, AZ31B is classified into AZ31B-H24 and AZ31B-O depending on temper designation. Thus, in this study, the laser weldability of AZ31B-H24 and AZ31B-O was investigated and compared. CW Nd:YAG laser was used to produce bead and butt joints. And the effects of welding conditions on the weldability of these joints were examined in detail. As a result of this study, AZ31B-H24 was found to have thinner oxide film and smaller grain size compared with AZ31B-O. Due to such difference, in bead welding, AZ31B-H24 had more wide welding range for full penetration compared with AZ31B-O. Furthermore, it was also confirmed that AZ31B-H24 and AZ31B-O have different welding conditions to obtain stable keyhole in butt welding.

• 한국기계가공학회지
• /
• 제10권6호
• /
• pp.83-88
• /
• 2011

Magnesium alloys have been focussed for the applications for lightweight of vehicle and electronics due to their high strength, low specific density and good damping capacity. This paper deals with the creep strength of Mg-Nd-Zr-Zn alloy. For the alloy, pure magnesium(99.9%) was melt with atmosphere of $0.3%SF_6$ and $25%CO_2$. After melting, 0.3% of zinc was inserted to stir for 10min at elevated temperature of $770^{\circ}C$. Master alloys of Mg-15%Nd and Mg-15%Zr were stirred in furnace. The creep tests were performed to obtain creep rate and rupture in the temperature range of 200 to $220^{\circ}C$ and 280 to $310^{\circ}C$ at an applied stress of 156 to 172MPa and 78 to 94MPa, respectively. The deformation mechanism was predicted dislocation climb from measured apparent activation energy and stress exponent. Also the increaser the temperature and stress the lower the stress exponent and activation energy. Finally, LMP parameter gives good information for the predicted creep rupture life.

• 한국표면공학회지
• /
• 제45권4호
• /
• pp.155-161
• /
• 2012

Magnesium alloys of AZ31, AZ31 + (0.5, 1, 1.5)wt.% CaO were cast, hot rolled, and oxidized between 450 and $650^{\circ}C$ in atmospheric air. The added CaO enabled to cast the AZ31 alloy in air. It decomposed and precipitated along the grain boundaries of the AZ31 alloy as $Al_2Ca$. The more the amount of CaO was, the more $Al_2Ca$ formed. The oxidation limit was about $450^{\circ}C$ for the AZ31 alloy. But, It increased to $650^{\circ}C$ in the CaO-added alloys. Hot rolling destroyed the precipitates that formed along the grain boundaries of the AZ31 alloy. During oxidation, MgO oxide scales that incorporated CaO formed at the outer surface of the formed oxide layer.

• 한국주조공학회지
• /
• 제31권5호
• /
• pp.243-248
• /
• 2011

Magnesium alloys have many advantages such as light-weight, high machinability, damping capacity, etc. So magnesium alloy parts have been used in transportation, mobile phone, military industries. Because of HCP atomic structure, Magnesium is very difficult in plastic deformation process, so most of magnesium products are fabricated by casting process. Magnesium alloys have low heat-capacity, high fluidity and low Fe solubility. For these reasons it is more suitable than aluminum in mass-production by casting. And various casting technologies have been developed. So casting technologies for magnesium developed recently is discussed in this paper.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2007년도 춘계학술대회 논문집
• /
• pp.281-281
• /
• 2007

• 대한용접접합학회:학술대회논문집
• /
• 대한용접접합학회 2008년도 춘계학술발표대회 개요집
• /
• pp.47-47
• /
• 2008