• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.13 no.6
• /
• pp.111-118
• /
• 2014

Aluminum lithium alloys are new materials developed for lightweight aircraft parts. However, as compared with conventional aluminum alloys in high-speed machining, problems such as tool wear, machining distortion, and cutting ability arise. This study presents the machining distortion characteristics of an Al-Li alloy wing tip in relation to the cutting heat in high-speed machining. A machining experiment was conducted with high-speed machining equipment for an evaluation of the machining distortion characteristics, with each machining stage temperature change of the workpiece machining surface, and the inside and outside temperature changes of the equipment measured. By measuring the amount of distortion of the workpiece before and after machining, the cutting heat was analyzed with regard to its effect on machining distortion in the product.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.23 no.5
• /
• pp.465-470
• /
• 2014

Thin and wide airfoils are difficult to be machined precisely because they are deformed during and after machining processes. This paper presents the results of the airfoil deformation measured by three-dimensional (3D) scanning equipment. It also discusses the influences of fixture and the machining process on the distortion of the thin airfoil. The simple fixture bended the thin airfoil to a U-shape at the first process, and the vacuum fixture decreased the distortion of the machined airfoil at the second process. The long and thin airfoil supported by two points was buckled during the machining at its two end-regions at the third process. Results from this study suggest that use of vacuum fixture decreases the machining distortion of thin and wide airfoils.

• Journal of the Korean Society for Precision Engineering
• /
• v.20 no.12
• /
• pp.191-197
• /
• 2003

As mechanical components are miniaturized, the demand on micro die and mold is increasing. Micro mechanical components usually have high hardness and good conductivity. So micro electrical discharge machining (MEDM) is an effective way to machine those components. In micro cavity fabrication using MEDM, it is observed that the bottom surface of cavity is distorted. Electric charges tend to be concentrated at the sharp edge. At the center of the bottom surface, debris can not be drawn off easily. These two phenomena make the bottom surface of the electrode and workpiece distort. As machining depth increases, the distorted shape of electrode approaches hemisphere. This process is affected by capacitance and the size of electrode. By using a smaller electrode than the desired cavity size and appropriate tool movement, bottom shape distortion can be prevented.

• International Journal of Precision Engineering and Manufacturing
• /
• v.6 no.4
• /
• pp.44-48
• /
• 2005

As mechanical components are miniaturized, the demands on micro die/mold are increasing. Micro mechanical components usually have high hardness and good conductivity. Micro electrical discharge machining (MEDM) can thus be an effective way to machine those components. In micro cavity fabrication using MEDM, it is observed that the bottom surface of the cavity is distorted. Electric charges tend to be concentrated at the sharp edge, and debris cannot be drawn off easily at the center of the bottom surface. These two phenomena make the bottom surface of electrode and workpiece distort. As machining depth increases, the distorted shape of the electrode approaches hemisphere. This process is affected by both capacitance and the size of electrode. By using a smaller electrode than the desired cavity size and appropriate tool movement, bottom shape distortion can be prevented.

• The Journal of Korean Academy of Prosthodontics
• /
• v.40 no.2
• /
• pp.156-171
• /
• 2002

The purpose of this study was to measure and compare the strains produced by screw-tightening implant frameworks fabricated by aye different fabrication methods; (1) one-piece cast using plastic sleeve, (2) one-piece cast using gold cylinder, (3) laser welding, (4) soldering, and (5) electrical discharge machining, and also to measure and compare the strains produced when the order of screw tightening was changed A research model incorporating eighteen strain gages was made to measure the fit of implant frameworks in three dimensions. Three implants aligned in an arc were fixed on the top ends of the L-shape aluminum bars of the research model, and standard abutments were joined to the implants with abutment screws. Five types of implant framework were placed on the abutments and screwed by a torque wrench using 10 Ncm. Under the conditions of this study, the following conclusions were drawn: 1. The electrical discharge machining group showed the smallest magnitude of strain, followed by the soldering group, the laser welding group, the one-piece cast group using gold cylinder, and the one-piece cast group using plastic sleeve. However, among the magnitude of strain for the remaining groups except the electrical discharge machining group, there were not significant differences. 2. When the order of screw tightening was changed, there were not significant differences in the magnitude of strain. 3. In comparison with the electrical discharge machining group, the laser welding group and the one-piece cast groups showed greater horizontal distortion and the soldering group showed greater horizontal and vertical distortion.

• Journal of Computational Design and Engineering
• /
• v.2 no.4
• /
• pp.248-252
• /
• 2015

Currently composite manufacturing process, such as linear friction welding plus NC machining, is the main method for the manufacturing and repairing of complex parts with integrated structure. Due to different datum position and inevitable distortion from different processes, it is important to ensure sufficient machining allowance for complex parts during the NC machining process. In this paper, a workpiece localization approach for machining allowance optimization of complex parts based on CMM inspection is developed. This technique concerns an alignment process to ensure sufficient stock allowance for the single parts as well as the whole integrated parts. The mathematical model of the constrained alignment is firstly established, and then the symmetric block solution strategy is proposed to solve the optimization model. Experiment result shows that the approach is appropriate and feasible to distribute the machining allowance for the single and whole parts for adaptive machining of complex parts.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2000.11a
• /
• pp.922-925
• /
• 2000

As mechanical components require size minimization and high precision, micro die machining technology has been developed in many fields. to machine a micro die by EDM, sometimes, a polygonal electrode is use. Machining corners by MEDM shows special characteristics. Physically, electrons are concentrated in sharp region and a high potential level is established in this region. Also, the electrode can't be rotated when machining a polygonal cavity, and machined debris can not drawn off easily. Discharge concentration in corners and 2nd discharge by machined debris result in distortion of corner shape. This phenomena can be improved by shaking the electrode. This method is also shown to be effective in improving surface roughness by circulation of machining fluid resulting from movement of the electrode.

• Journal of the Korean Society for Precision Engineering
• /
• v.26 no.9
• /
• pp.127-134
• /
• 2009

Laser-assisted machining uses primarily laser power to heat the local area before the material is removed. It not only efficiently reduces the cutting force during the manufacturing process but also improves the machining characteristics and accuracy with regard to difficult-to-machine materials. The prediction of relative deformations between the cutting tool and workpiece is important to improve the accuracy of machined components. This paper presents the deformation errors caused for a cylindrical workpiece by thermal effects in the laser-assisted machine tool using finite element method. The results can be used to increase the cutting accuracy by compensating thermal distortion prior to laser-assisted machining.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2006.05a
• /
• pp.493-494
• /
• 2006

SU-8 can be implemented as a mask for micro Abrasive Jet Machining (micro-AJM) process [1]. In this paper, we will evaluate the quality of micro grooving result on glass substrate by micro-AJM process which using SU-8 as a mask. It was evaluated on width and edge profile of the micro grooving. The result was having distortion compare with the master film used to pattern the SU-8 mask. The value of distortion with other properties which came along with it, such as depth and surface roughness, can be optimized in order to fabricate micro-channel for micro-fluidic application.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.20 no.3
• /
• pp.310-315
• /
• 2011

General portal machine represents a distinct weak spot concerning their structural behavior because of long protruding structure components, such as saddles and rams. The weak point causes the deformation of the machine tool and consequently rises a severe machining error. The purpose of this study is to improve the structural design of crossrail in order to minimize it's distortion. Tool Center Point (TCP) was chosen as a reference point for evaluating the distortion effect of a crossrail and topological optimization was adopted as a method of structural design improvement. The displacements of TCP according to the machining positions were investigated by structural analyses for both of original crossrail design and the improved one. The comparing results showed that the displacement of TCP could be reduced about 55% maximum.