• The Sea:JOURNAL OF THE KOREAN SOCIETY OF OCEANOGRAPHY
• /
• v.29 no.1
• /
• pp.1-13
• /
• 2024

The southwestern part of the East Sea is known to have a high primary productivity compared to those in the northern and eastern parts, which is attributed to nutrients supplies either by Tsushima Warm Current or by coastal upwelling. However, research on the biological pump in this area is limited. We developed machine learning models to estimate net community production (NCP), a measure of biological pump, with high spatial and time scales of 4 km and 8 days, respectively. The models were fed with the input parameters of sea surface temperature, chlorophyll-a, mixed layer depths, and photosynthetically active radiation and trained with observed NCP derived from high resolution measurements of surface O₂/Ar. The root mean square error between the predicted values by the best performing machine model and the observed NCP was 6 mmol O₂ m^-2 d^-1, corresponding to 15% of the average of observed NCP. The NCP in the central part of the Ulleung Basin was highest in March at 49 mmol O₂ m^-2 d^-1 and lowest in June and July at 18 mmol O₂ m^-2 d^-1. These seasonal variations were similar to the vertical nitrate flux based on the ³He gas exchange rate and to the particulate organic carbon flux estimated by the ²³⁴Th disequilibrium method. To expand this method, which produces NCP estimate for spring and summer, to autumn and winter, it is necessary to devise a way to correct bias in NCP by the entrainment of subsurface waters during the seasons.

• Journal of Advanced Marine Engineering and Technology
• /
• v.40 no.7
• /
• pp.629-634
• /
• 2016

This paper describes the implementation of a ZigBee sensor node that can be utilized as a multiband and machine to machine (M2M) communication gateway. The IEEE 802.15.4-2003 standard was used as the wireless network frequency band. Ember's Type EM357 SoC was used as the transmission and reception device to perform the communication function, and it was also used for both the main M2M gateway and the sensor node. For the implementation of the operating protocol, EmberZNet Stack 4.5.4 from the Ember Corporation was used. The measurement of the reception sensitivity in the receiving module and the actual output signal from the reference were obtained from the transmission of a packet, and the packet included the M2M gateway within the attached ZigBee sensor. The packet error rate was measured as 0% with a -98 dBm reception sensitivity at the ZigBee frequency. In addition, excellent current characteristics of the ZigBee modules were shown by the implementation of the low-power circuit.

• Transactions of Materials Processing
• /
• v.18 no.2
• /
• pp.144-149
• /
• 2009

Recently, the monitoring technology of machining process is very important to improve productivity and quality in manufacturing filed. Such monitoring technology has been performed to measurement using vibration signal, acoustic emission signal and tool dynamometer. However, micro machining is limited small-scale parts machining because micro tool is very small and weakness to generate signal in micro machining process. Therefore, this study has efficient sensing technology for real monitoring system in micro machine that is proposed to supplement a disadvantage of single-sensor by multi sensor. From experimental result, it was evaluated tool wear and cutting situation according to repetitive slot cutting condition and changing cutting condition, and it was performed monitoring spindle rpm and condition according to compare acceleration signal with current signal.

• Journal of Broadcast Engineering
• /
• v.21 no.3
• /
• pp.298-306
• /
• 2016

With the advent of Internet of Things (IoT) technology that allows the communications between things and devices over the Internet, a lot of researches on the IoT services, such as smart home or healthcare, have been progressed. In the existing machine-to-machine (M2M) communications, however, since the underlying link-layer technologies, such as Bluetooth or ZigBee, do not use the Internet Protocol (IP) communication, those technologies are not suitable to provide the IoT services. Accordingly, this paper discusses how to provide the Internet services in the M2M communication, and propose an implementation of the Constrained Application Protocol (CoAP) over 6LoWPAN for providing IoT services in the BLE networks. Based on the implementation, we compared the performance between HTTP and CoAP for IoT communications. From the experimental results, we can see that the CoAP protocol gives better performance than the HTTP protocol with two times higher throughput, 21% faster transmission time, and 22% smaller amount of generated packets.

• Journal of Animal Environmental Science
• /
• v.15 no.2
• /
• pp.99-106
• /
• 2009

We conducted a comparison experiment of our wide-area spraying high speed fan with a fan which was developed by Japan MARUYAMA Inc. have been much recognized for it's history and skills in a field of spraying machine. In result, MARUYAMA Inc. fan sprayed up to 120 m and, on the other hand, wide-area spraying high speed fan of our own making was able to spray up to more than 160 m. Wide-area spraying machine have been supplied to domestic demands by importing from Japan, but it is determined to be possible that home products will occupy market for it's ability, price and A/S environment in future. The main research results are below. Some plastic cups which are in the open market are used for our experiment. After distributing 90 cups in a range of 10m vertically with localizing 5 cups horizontally and 18 cups vertically, spraying machine was moved and finally we make distribution charts by estimating the sprayed amounts on each cup. Vertical distance was set up to 5m and we calculated average values by using sprayed amount and data of 4 observers. In result our fan showed much sprayed amounts than MARUYAMA Inc. all over the field except situations of vehicle departing and stopping.

• Journal of Drive and Control
• /
• v.16 no.4
• /
• pp.74-79
• /
• 2019

In this study, an edible fresh corn harvest testing machine was designed and manufactured. And harvesting performance was analyzed through the field test. The testing machine is of the tractor attached type. It is connected to the tractor PTO shaft to transfer power to the each part of the harvesting machine. And it harvests fresh corn by one row through the processes of cutting, stem crushing, detaching, and collecting. The performance test was performed at PTO speed (540, 750, 1050 rpm, respectively), working speed (0.1, 0.15, 0.2 m/s, respectively), and cropping cultivation (row spacing·hill spacing 70·25 cm, 70·40 cm, 90·30 cm, respectively). The performance test was repeated three times in the 15 m section. The detachment loss ratio, uncollected crop ratio, damage ratio, and harvest ratio were analyzed. As a result of the performance test, it was analyzed that the PTO speed 540 rpm, running speed of 0.1 m/s, and row spacing·hill spacing 70·40 cm were the optimal condition.

• Journal of the Korean Society for Precision Engineering
• /
• v.30 no.3
• /
• pp.324-330
• /
• 2013

This paper describes a novel method to surface large optics mirror with an extremely high hardness, which could replace the high cost of the repetitive off-line measurement steps and the large ultra-precision grinding machine with ultra-positioning control of 10 nm resolution. A lot of diamond pellet to be attached on the convex aluminum base consists of a grinding tool for the concave large mirror, and the tool was pressured down on the large mirror blank. The tool motion at an interval on the spiral path was controlled with each feed rate as the dwell time in the conventional computer-controlled polishing. The shape to be surfaced was measured directly by a touch probe on the machine without any separation of the mirror blank. Total 40 iterative steps of the surfacing and measurement could demonstrate the form error of RMS $7.8{\mu}m$, surface roughness of Ra $0.2{\mu}m$ for the mirror blank with diameter of 1 m and spherical radius of curvature of 5400 mm.

• Journal of Korean Society for Quality Management
• /
• v.22 no.2
• /
• pp.127-142
• /
• 1994

In these days, the PCs are widely used in the mid-level factory. But they have low-effectiveness for using them. The main reason should be the lack of useful and practical software in the market. This Case study aimed at the support of the software using DB Language to get M/M chart for aquiring work study and standard time data in the mid-level factory having multi-item and multi-process type. CVA (Chronocycle Video Analysis) is applied to get basic standard time data and working list. Standard time, Sequence of working and allowance time or rate for man and machine will be readily obtained through the menu when the software executing. Detailed program list is systematically shown in Appendix.

• Proceedings of the Korean Society of Machine Tool Engineers Conference
• /
• 2000.04a
• /
• pp.673-678
• /
• 2000

This paper presents an indirect compensation of thermal errors during machining, in which thermal error is modeled as a linear regression of temperatures measured at 4 specified positions. In this regression model, weighting coefficients of the measured temperatures were estimated by using the least square method. The grinding test with compensation, after 4-hour warming-up operation before the test, showed that the maximum machining error of the work pieces was reduced to 12${\mu}{\textrm}{m}$ while it measured 28${\mu}{\textrm}{m}$ without compensation. Furthermore the standard deviation of machining errors was also reduced from 8${\mu}{\textrm}{m}$ to 2${\mu}{\textrm}{m}$.

• Journal of the Korean Institute of Navigation
• /
• v.20 no.4
• /
• pp.81-98
• /
• 1996

The purpose of this study was analysis of the muscle action in physical exercise in the rolling machine. The rolling machine moved by eletric power-driven was made to keep the constant cycle and size of rolling. The subjects of this study consist of 4 seaman(SM) and 4 landman (LM). The experiment analyzed the muscle power of lower and upper limbs by Intergrated Electromyogram(IEMG). The measurement was made on the ground, and 6 and 8 degrees of rolling separately. This study concludes as follows ; including analysis of IEMG of heavy exercise in two hands curl, a standstill walking and just standing. 1. IEMG of the lower limbs when standing. 1) In 6 degrees of rolling, for the landman(LM), vastus medialis m.(9.73), vastus lateralis m.(9.55), and rectus femores m.(8.73) acted more. As for the seaman(SM), tibialis anterior m.(5.38), biceps femores m.(5.05), and gastrocnemius m.(4.47) acted more. 2) In 8 degrees of rolling, in common, for both LM and SM, it were vastus medialis m.(11.20 and 8.97), vastus lateralis m.(16.20 and 4.63), and tibialis anterior m.(5.13 and 4.47). 3) It was showed that IEMG of LM was larger than that of SM. 2. IEMG of the lower limbs when walking. 1) On the ground, for the LM, gastrocnemius m.(7.08), vastus medialis m.(6.65), and vastus latralis m.(6.60) acted more. As for the SM, vastus lateralis m.(7.08), vastus medialis m.(6.58) and restus femores m.(5.10) acted more. 2) In both 8 and 6 degrees of rolling, vastus medials m.(14.50 and 11.98), vastus lateralis m.(10.10 and 14.10), and gastrocnemius m.(11.75 and 7.10) acted more in two groups. 3) It was showed that IEMG of LM was larger than that of SM. 3. IEMG of the lower limbs when heavy exercise(two hands curl). 1) On the ground, for the LM, vastus lateralis m.(21.68), vastus medialis m.(16.08), and rectus femores m.(14.08) acted more. As for the SM, tibialis anterior m.(16.08), vastus medialis m.(14.58), and vastus lateralis m.(8.78) acted more. 2) In 8 and 6 dgrees of rolling, it were vastus medialis m.(17.05 and 12.45), vastus lateralis m.(37.98 and 17.08), and tibialis anterior m.(19.83 and 13.20). 3) It was showed that IEMG of LM was larger than that of SM. 4. IEMG of the upper limbs when heavy exercise. 1) On the ground, the brachialis m.(44.30 and 17.80), and biceps brachii m.(13.40 and 25.10) acted more in two groups. 2) In both 6 and 8 degrees of rolling, the brachialis m.(37.60 and 24.35), and biceps brachii m.(11.38 and 7.97) acted more in two groups. 3) It was showed that IEMG of SM was larger than that of LM.