• Proceedings of the Korean Society of Surveying, Geodesy, Photogrammetry, and Cartography Conference
• /
• 2002.04a
• /
• pp.173-186
• /
• 2002

서로 다른 공간해상도와 분광해상도를 가진 영상들을 이용하여 영상지도를 제작할 때 공간해상도를 향상시킬 수 있는 영상융합기법에 대해 연구하였다. 사용된 영상은 IKONOS panchromatic 영상과 multispectral 위성영상, KOMPSAT-1호 위성영상과 SPOT XS 위성영상에 대해 Brovey, IHS, PCA, HPF, CN, MWD 융합기법을 적용하여 시각적 분석, 공간정보의 분포특성, 통계적 특성을 기준으로 분석하였으며, 시각적 분석에서는 IHS, PCA 융합기법이, 통계적 분석에서는 HPF, MWD 융합기법이 좋은 결과를 보여주었으며, 종합적인 결과분석을 고려할 때 MWD 융합기법이 원 영상의 분광정보를 가장 작게 왜곡시킴을 알 수 있었다.

• Proceedings of the Korean Nuclear Society Conference
• /
• 1996.05c
• /
• pp.201-206
• /
• 1996

건식가공(Dry Process)이 사용전,후 DUPIC 핵연료의 붕괴열(Decay Heat), Hazard Index, 조사선량률(Dose Rate) 등에 미치는 영향을 계산하고, 그 원인을 분석하였다. DUPIC 사용방안으로 표준 연소도(35,000 MWD/MTU)의 경우와 장주기 연소도(50,000 MWD/MTU)의 경우를 고려하여 계산하였으며, DUPIC핵연료는 20년 냉각후 가공하는 것을 기준으로 하였다. 또한 DUPIC핵연료 장전시 고려할 수 있도록 사용전 DUPIC 핵연료에 대한 계산을 핵연료 집합체(Bundle) 단위로 하였다. 조사선량과 붕괴열은 건식가공에 상당히 민감한 반응을 보였고 이는 주로 Cs의 제기에 의한 것이다.

• Proceedings of the Korean Nuclear Society Conference
• /
• 1995.05b
• /
• pp.799-804
• /
• 1995

DUPIC 핵연료의 사용전 그리고 사용후 조건에서 방사선량을 분석하였다. 사용후 핵연료로 35,000 MWD/MTU의 표준 연소도와 50,000 MWD/MTU의 고 연소도을 사용하였고 선량률을 계산하기 위해 CANDU의 핵연료 집합체을 균등 혼합체로 가정 하였다. 조사선량율은 건식가공을 거치지 않았을 때 매우 높은 수치를 나타내었지만 건식가공을 한 후에는 많이 감소하개 됨 을 볼 수 있었다. 특히 Cs에 민감한 반응을 보였고 Cs을 100% 제거하였을 경우 전체 선량율이 약 90%가 줄어드는 결과를 얻었다. 아울러 사용후 DUPIC핵연료의 선량율도 건식가공 방법에 많은 영향을 받고 있다.

• Journal of Korean Society of Water and Wastewater
• /
• v.13 no.2
• /
• pp.66-73
• /
• 1999

This study was carried out to derive the removal characteristics of target materials(DOC and turbidity) during the coagulation process after the injection of coagulants(PACl and FeCl3). Used apparatus were a jar test and a pilot plant. A great portion of DOC among the total removed DOC was achieved at the slow mixing process among the coagulation process. The ranges of removed DOC and optimum pH for each coagulant were 0.45~1.47mg/l and 6.0~6.5 by PACl, and 0.97~2.61mg/l. and 5.0~5.5 by FeCl3, respectively. Both of coagulants showed little increase of DOC removal above coagulant dosage 20mg/l Molecular weight distribution(MWD) of removed DOC was measured by get filtration(GF) technique. The MWD variation by gel filtrationin(GF) for removed DOC in the coagulation process were as follows; for raw water, the percentages of each MWD for total area were < MW 6,500 25.5%, MW 6,500~66,000 67.1%, and > MW 66,000 7.4%. For the same coagulant dosage(12mg/l), the percentages of each MWD for total area by PACl were < MW 6,500 20.5%, MW 6,500~66,000 48.7%, and > MW 66,000 9.1%, and those of FeCl3 were MW 66,000 18.2%. For each coagulant, the removal percentage of MW 6,500~66,000 occurred a little, but at a part of

• Journal of the Korean Society of Surveying, Geodesy, Photogrammetry and Cartography
• /
• v.22 no.4
• /
• pp.359-365
• /
• 2004

Data integration techniques are becoming increasing1y important for conquering a limitation with a single data. Image fusion which improves the spatial and spectral resolution from a set of images with difffrent spatial and spectral resolutions, and image registration which matches two images so that corresponding coordinate points in the two images correspond to the same physical region of the scene being imaged have been researched. In this paper, we compared with six image fusion methods(Brovey, IHS, PCA, HPF, CN, and MWD) with panchromatic and multispectral images of IKONOS and developed the registration method for applying to SPOT-5 satellite image and RADARSAT SAR satellite image. As the result of tests on image fusion and image registration, we could find that MWD and HPF methods showed the good result in term of visual comparison analysis and statistical analysis. And we could extract patches which depict detailed topographic information from SPOT-5 and RADARSAT and obtain encouraging results in image registration.

• Elastomers and Composites
• /
• v.44 no.2
• /
• pp.156-163
• /
• 2009

Our objective is to increase the flowability of Polypropylene(PP) compounds and achieve flow mark free surface in injection molded specimen. We have investigated flowabilities of PP compounds which were composed of PP, rubber, talc, and trace amount of additives. Flowability measurement was performed with four types PPs of which molecular weight distributions(MWD) and melt indexes(MI) were different. Rheological properties of the PP compounding materials, such as spiral flow(SF) length, MI, and shear viscosity, were evaluated. When PP with the broad MWD was used, there were remarkable cases where the spiral flow length of low MI PP compound was longer than that of higher MI PP compound. The PP compound having low MI but broad MWD PP has more flowability than the compound with only high MI.

• Nuclear Engineering and Technology
• /
• v.41 no.8
• /
• pp.1109-1114
• /
• 2009

The evolution of a high burnup structure (HBS) in a light water reactor (LWR) $UO_2$ fuel was simulated using the Potts model. A simulation system for the Potts model was defined as a two-dimensional triangular lattice, for which the stored energy was calculated from both the irradiation damage of the $UO_2$ matrix and the formation of a grain boundary in the newly recrystallized small HBS grains. In the simulation, the evolution probability of the HBS is calculated by the system energy difference between before and after the Monte Carlo simulation step. The simulated local threshold burnup for the HBS formation was 62 MWd/kgU, consistent with the observed threshold burnup range of 60-80 MWd/kgU. The simulation revealed that the HBS was heterogeneously nucleated on the intergranular bubbles in the proximity of the threshold burnup and then additionally on the intragranular bubbles for a burnup above 86 MWd/kgU. In addition, the simulation carried out under a condition of no bubbles indicated that the bubbles played an important role in lowering the threshold burnup for the HBS formation, thereby enabling the HBS to be observed in the burnup range of conventional high burnup fuels.

• Nuclear Engineering and Technology
• /
• v.29 no.3
• /
• pp.201-210
• /
• 1997

A thermal conductivity correlation has been proposed which can be applied to high turnup fuel by considering both of thermal conductivity with turnup across fuel pellet and additional degradation at pellet rim due to very high porosity. In addition, a correlation has been developed that can estimate the porosity of rim region as a function of rim burnup under the assumptions that all the produced fission gases are retained in the in porosity and threshold pellet average burnup required for the formation of rim region is 40 MWD/㎏U. Rim width is correlated to rim burnup using measured data. For the RISO experimental data obtained at pellet average turnup of 43.5 MWD/㎏U for three linear heat generation rates of 30, 35 and 40 ㎾/m, radial temperature distributions ore calculated using the present correlation and compared with the measured ones. This comparison shows that the present correlation gives the best agreement with the measured data when it is combined with the HALDEN's correlation for thermal conductivity considering its degradation with burnup. Another comparison with the HALDEN's measured fuel centerline temperature as a function of burnup at 25 ㎾/m up to about 44 MWD/㎾U also suggest that the present correlation yields the best agreement when it is combined with the HALDEN's thermal conductivity.

• Proceedings of the Korean Radioactive Waste Society Conference
• /
• 2004.06a
• /
• pp.340-341
• /
• 2004

최근에는 경수로 핵연료의 연소도를 높이고 있으며 연소도가 증가함에 따라서 핵분열생성물(불순물)의 양은 증가하게 된다. 핵분열생성물의 함량은 산화속도 및 분말특성에 영향을 주는 것으로 알려져 있다. 소결성을 갖는 분말의 제조 및 특성 실험은 사용후 핵연료가 고방사능을 가져 실험수행상에 제한이 많아 실제 사용후 핵연료를 모사한 모의 사용후 핵연료를 사용하여 수행하고 있다. 본 연구에서는 연소도가 35,000 MWD/MTU 및 60,000 MWD/MTU인 모의 사용후 핵연료를 제조하여 연소도에 따른 산화ㆍ환원처리 분말 및 미분쇄 분말의 분말특성, 소결온도 및 성형압력에 따른 소결성을 조사하였다.(중략)

• Elastomers and Composites
• /
• v.32 no.3
• /
• pp.173-178
• /
• 1997

In this study, the ultrasonic irradiation in elevated pressure was used to alter the molecular weight and MWD of polystyrene. The high pressure reactor was filled with 0.5w/v% polystyrene solution, and then it was pressurized from 500psi to 4000psi. The ultrasound was irradiated in 10 minutes at each pressure, and the extract was collected and analyzed by GPC. Molecular weight distribution was predicted by log-normal and Schulz distribution function. The average molecular weight and polydispersity of polystyrene were decreased, as the pressure applied during the ultrasonic irradiation was increase. It was able to fractionate polymer material and control polydispersity by adjusting pressure in the ultrasonic irradiation.