• 전력전자학회논문지
• /
• 제18권5호
• /
• pp.485-491
• /
• 2013

A new passive lossless snubber for boost converter based on magnetic coupling is proposed. It is composed of a winding coupled with boost inductor, one snubber inductor, two snubber capacitor and three additional diodes. Especially, the snubber inductor can not only limit the reverse recovery current of output diode but also minimize switch turn-on losses greatly. Moreover, all of the energy stored in the snubber is transferred to the load in the manner of resonance. To confirm the validity of proposed system, theoretical analysis, design consideration, and verification of experimental results are presented.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2006년도 제37회 하계학술대회 논문집 C
• /
• pp.1687-1688
• /
• 2006

This paper presents the results of a grid-connected photovoltaic (PV) system modeling that contain incremental conductance MPPT(Maximum Power Point Tracking) controller by PSCAD/EMTDC simulator and investigates the influence that tan occur in the grid-connected PV system from aspect of power quality, i.e. voltage drop, total harmonic distortion(THD) and total demand distortion(TDD). The measured data the PV array modeling of PSCAD/EMTDC in Cheongwadae, Seoul, Korea is used in the paper.

• 전력전자학회:학술대회논문집
• /
• 전력전자학회 2002년도 추계학술대회 논문집
• /
• pp.69-73
• /
• 2002

A study on photovoltaic system has a lot of problems. Such as repetition experiment in the same condition, development of MPPT(Maximum Power Point Tracking) algorithm, development of islanding detection algorithm and so forth. The reason Is that solar cell output characteristics are varied by insolarion and surface temperature of solar cell. Therefore, the assistance equipment is required which emulates the solar cell characteristics. In this paper, propose the new modeling of solar cell and verify this modeling using MATLAB simulation. And experiment virtual implement of solar cell system using this modeling.

• Journal of Electrical Engineering and Technology
• /
• 제9권3호
• /
• pp.1072-1079
• /
• 2014

This paper introduces a coordinated droop control for the stand-alone DC micro-grid, which is composed of photo-voltaic generator, wind power generator, engine generator, and battery storage with SOC (state of charge) management system. The operation of stand-alone DC micro-grid with the coordinated droop control was analyzed with computer simulation. Based on simulation results, a hardware simulator was built and tested to analyze the performance of proposed system. The developed simulation model and hardware simulator can be utilized to design the actual stand-alone DC micro-grid and to analyze its performance. The coordinated droop control can improve the reliability and efficiency of the stand-alone DC micro-grid.

• Journal of Power Electronics
• /
• 제7권2호
• /
• pp.174-180
• /
• 2007

In this paper, a simple control method for two-stage utility grid-connected photovoltaic power conditioning systems (PCS) is proposed. This approach enables maximum power point (MPP) tracking control with post-stage inverter current information instead of calculating solar array power, which significantly simplifies the controller and the sensor. Furthermore, there is no feedback loop in the pre-stage converter to control the solar array voltage or current because the MPP tracker drives the converter switch duty cycle. This simple PCS control strategy can reduce the cost and size, and can be utilized with a low cost digital processor. For verification of the proposed control strategy, a 2.5kW two-stage photovoltaic grid-connected PCS hardware which consists of a boost converter cascaded with a single-phase inverter was built and tested.

• 전기학회논문지
• /
• 제64권10호
• /
• pp.1432-1439
• /
• 2015

The solar array regulator supplies the electric power to the battery and the other units of a satellite by controlling the operating point of a solar array. In this paper, the solar array regulator composed with analog circuits is proposed. The solar array regulator has three modes. The first is a maximum power point tracking mode for harvesting the maximum photovoltaic power generation. The second is a power limitation mode which is designed for optimizing the volume and weight of the solar array regulator by preventing the excessive power conversion. The last constant voltage mode is proposed to keep the Li-Ion battery is not over-charge. The small signal model of the solar array regulator which has the reversed input and output variables in comparison with conventional converter is established and the stability is analysed. Finally, the proposed design of the solar array regulator is verified by experiments.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2005년도 제36회 하계학술대회 논문집 B
• /
• pp.1438-1440
• /
• 2005

A power control and distribution unit(PCDU) plays roles of protection of battery against overcharge by active control of solar array generated power, distribution of unregulated electrical power via controlled outlets to bus and instrument units, distribution of regulated electrical power to selected bus and instrument units, and provision of status monitoring and telecommand interface allowing the system and ground operate the power system, evaluate its performance and initiate appropriate countermeasures in case of abnormal conditions. In this work, we perform the preliminary design of a PCDU scheme for the small LEO Satellite applications. The main constitutes of the PCDU are the battery interface module, the auxiliary supply modules, solar array regulators with maximum power point tracking(MPPT) technology, heater power distribution modules, internal converter modules for regulated bus voltage generation. and instrument power distribution modules.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2004년도 추계학술대회 논문집 전력기술부문
• /
• pp.204-207
• /
• 2004

The paper proposes a simulation model of grid-connected photovoltaic generation system (PV system) using on PSCAD/EMTDC, a reliable power system and apparatus transient analysis program. A equivalent circuit model of a solar cell is used for modeling solar array. A series of parameters required for array modeling are deduced from general specification data of a solar module. A PWM voltage source inverter (VSI) model is presented and current control scheme is implemented for VSI control. A maximum power point tracking (MPPT) technique is applied for controlling the PV system. Simulation case study provides V-I and V-P characteristics of solar array and PV system control performance for irradiation changes.

• 전력전자학회:학술대회논문집
• /
• 전력전자학회 2010년도 추계학술대회
• /
• pp.64-65
• /
• 2010

본 논문에서는 250kW급 태양광발전용 인버터에 대한 국내외 기술기준 및 계통연계접속기준에 의한 성능평가방법 및 장비에 대해 소개하고자 한다. 효율, MPPT(maximum power point tracking) 효율 등 정상상태 및 과도상태 성능과 각종 보호기능을 시험할 수 있는 태양전지 및 전력계통 시뮬레이터, 부하장치 등 각종 시험장비의 구성과 시험 방안에 대하여 기술하였으며 국내 기술기준에 의한 시험 결과를 제시하고자 한다.

• 한국태양에너지학회 논문집
• /
• 제32권spc3호
• /
• pp.245-254
• /
• 2012

In photovoltaic system, the characteristics of photovoltaic module such as open circuit voltage and short circuit current will be changed because of cell temperature and solar radiation. Therefore, the boost converter of a PV system connects between the output of photovoltaic system and DC link capacitor of grid connected inverter as controlling duty ratio for maximum power point tracking(MPPT). This paper shows the dynamic characteristics of the boost converter by comparing single-loop and two-loop control algorithm using both analog and digital control. Both proposed compensation methods have been verified with computer simulation to demonstrate the validity of the proposed control schemes.