• 한국전기전자재료학회논문지
• /
• 제22권4호
• /
• pp.290-296
• /
• 2009

$Bi_{4}Ti_{3}O_{12}$ (BiT) thin films were grown on the Pt/Ti/$SiO_2$/si substrate using a metal organic decomposition (MOD) method. Effects of oxygen annealing on the structural properties and dielectric properties of the BiT thin films were investigated. The BiT films were well developed when rapid thermal annealed at $>500^{\circ}C$ in oxygen ambient. For the film annealed at $700^{\circ}C$, no crystalline phase was observed under oxygen free annealing atmosphere while its crystallinity was significantly enhanced as the oxygen pressure increased. The BiT film also exhibited a smooth surface with defect free grains. A high dielectric constant and a low dielectric loss were achieved satisfactory in the frequency range from 75 kHz to 1 MHz. Especially, the BiT film, annealed at $700^{\circ}C$ and 10 torr oxygen pressure, showed good dielectric properties: dielectric constant of 51 and dielectric loss of 0.2 % at 100 kHz. Its leakage current was also considerably improved, being as $0.62\;nA/cm^2$ at 1 V. Therefore, it is considered that the oxygen annealing has effects on an enhancement of crystallinity and dielectric properties of the BiT films.

• Spatial Information Research
• /
• 제2권2호
• /
• pp.147-163
• /
• 1994

본 고는 위상관계를 지니는 vector GIS데이터구조로 부터 교통계획이나 도로계획시 필요한 node-link중심의 교통망 자료를 획득하기 위한 절차 및 활용프로그램을 제시하는데 목적이 있다. 이를 위해 ARC/INFO GIS와 UTPS(Urban Transportation Planning System)계의 TRANPLAN이 구현을 위한 대표적 소프트웨어로서 선정되었고, 상호간 데이터의 교환을 위한 세가지으 위상변환(Topology Conversion)방법이 제시되었다. 첫번째 방법은 소프트웨어 개발자(ARC/INFO의 ESRI및 TRANPLAN Urban Analysis Group)들이 공동개발하여 별도의 소프트웨어 package로 구축한 프로그램에 대해서 변환절차의 개요 및 프로그램의 단계적 확대방안에 관해서 소개하였고, 둘째로 ARC/INDO에서 사용가능한 node attribute table(NAT)을 별도의 topology로 구축하여 acc attribute table(AAT)및 NAT에 있어서의 node체계를 상호 관련시켜서 node-link교통망 자료로 변환하는 알고리즘 AML(Arc Macro Language)로서 제시했으며, 끝으로 FOR-TRAN언어를 사용한 AAT에서의 node변환 알고리즘을 소개하였다. 이러한 GIS데이터의 위상변환의 필요성은 GIS를 교통부문에(특히 교통수요 예측)직접 이용함은 물론 더 나아가서는 양자사이으 효율적인 데이터의 교환이 그목적이라고 할 수 있다. 비록, 본고에서는 이들 세가지 방법 상호간의 구체적인 장단점에 관해서는 토의되지 못했지만 세방법중 어떠한 것이든 교통수요 예측모형을 위한 데이터의 변환과정에 역할을 할 수 있으며, 이들 시스템간의 효율적 통합은 교통계획과정에서의 생산성 향상에 기여할 것으로 보인다.

• 한국인터넷방송통신학회논문지
• /
• 제8권2호
• /
• pp.15-21
• /
• 2008

본 논문에서는 2진논리의 확장을 Galis체상에서 해석하여 확장논리에 기초한 순차디지털논리시스템과 컴퓨터구조의 핵심인 연산알고리즘을 논의하였다. 순차디지털논리시스템은 Building Block으로서 T-gate를 사용하였으며, 차순상태함수, 출력함수를 도출하여 최종 궤환이 없는 Moore Model의 순차디지털논리시스템을 구성하였다. 그리고, 컴퓨터구조에서 중요한 연산알고리즘의 핵심인 가산, 감산, 승산 및 제산 알고리즘을 유한체의 수학적 성질을 토대로 각각 도출하였다. 특히, 유한체 GF($P^m$)상에서 P=2인 경우는 기존의 2진디지털논리시스템에 적용이 용이하다는 장점이 있으며, mod2의 성질에 의해 감산 알고리즘은 가산 알고리즘과 동일하다. 제안한 방법은 기존의 2진논리를 확장할 수 있어 좀 더 효율적으로 디지털논리시스템을 구성할 수 있을 것으로 사료된다.

• Journal of Nutrition and Health
• /
• 제32권1호
• /
• pp.83-89
• /
• 1999

The present study was conducted to investigate the yields of volume, thiamin and riboflavin from the milk of twenty-five Cesarean-section women, and their ingestion in infants. We measured the consumed volume of human milk of infants by the test-weighing method, and thiamin riboflavin contents were determined by fluorescence spectroscopy during the first 7 days postpartum. Thiamin contents of the milk averaged 24.3, 24.0, 27.4 and 30.2ug/100g. Thiamin and riboflavin contents of the milk both increased during the lactation ps mod(p<0.05). The first secretion of breast milk occurred from the 4th to 5th day postpartum in Cesarean-section women. The consumed volume of human milk was 63, 81, 104 and 133g/day at 4, 5, 6 and 7 days postpartum and the consumed volume of formula milk was 58, 176, 292, 323, 308, 321 and 318g/day at 1, 2, 3, 4, 5, 6 and 7 days postpartum and the consumed volume of formula from the human and formula milk were 26.6, 91.0, 151.0, 172.5, 169.2, 175.9 and 172.9ug/day. Total daily riboflavin ingestion from the human and formula milk were 26.6, 91.0, 151.0, 172.5, 169.2, 175.9 and 172.9ug/day. Total daily riboflavin ingestion from the human and formula milk was 48.7, 166.8, 277.6, 318.2, 312.0, 327.0 and 335.7ug/day at 1, 2, 3, 4, 5, 6 and 7 postpartum. These results suggest that the milk secretion of Cesarean-section women is delayed a few days and the yield volume of milk is less than that of normal delivery women, but thiamin and riboflavin contents of the milk are not different from those of milk of normal-delivery women.

• 복식
• /
• 제33권
• /
• pp.5-25
• /
• 1997

The purpose of this study was to analyze the characteristics of the Junk Art represented in the second half 20the century fashion. The highly developed material civilization resulted in human alienations environmental distruption. By this fact human being of the 20the century was to overcome social com-plexity. In this respect this research was focused that how the characteristics of the junk Art was expressed in the second half 20th century fashion. The concepts of the Junk Art lied in the creation of art work in the 2-dimentional plane of 3-dimentional space through the application of all junks (wood pieces industrial debris trash ready-made goods etc) cast by the mod-ern industrial society and the mass production system. Juck Art had been further envigorated in the footstep of the development of the collage method based on the creation of object aes-thetics. And junk artists have untitled social environments with art by assembling junks as a way of exploring the material world of cur-rent society and provided infinite possibilities of expressional medium and technique. Above all junk Art has been reflected in the fashion as well as other art. Especially a lot of the fashion design by the use of junks and the expressive image of junks is produced in the 20th century. That is many of fashion designers have always been aware of what is happening in the arts and have always been able to use the dis-coveries and ideas of the artist to help them solve design problems and creat fashion which are new inventive and reflective of their time. The fashion designers of the junk fashion design could be said to have presented much more possibilities and new development for-mulas to modern fashion design and provided a new order of other formative arts. Unlike the negative and destructive punk cyberpunk fashion junk fashion was a positive and optimistic aesthetics. junk fashion that keeps pace with science and the development of technology is devoted to trying to grasp the real form of ultimate re-ality.

• 한국재료학회지
• /
• 제23권5호
• /
• pp.293-298
• /
• 2013

In this study, an HP-mod. type(KHR-45A), which is used as a heater tube material in the pyrolysis process, was evaluated for its carburizing properties. It was confirmed from the microstructural observation of the tubes that the volume fraction of carbide increased and that the coarsening of Cr-carbide generated as a degree of carburization increased. The depth of the hardened layer, which is similar to the thickness of the carburized region of each specimen, due to carburization is confirmed by measurement of the micro-Vickers hardness of the cross section tube, which thickness is similar to that of the carburized region of each specimen. Two types of chromium carbides were identified from the EBSD (electron back-scattered diffraction) image and the EDS (energy-dispersive spectroscopy) analysis: Cr-rich $M_{23}C_6$ in the outer region and Cr-rich $M_7C_3$ in the inner region of tubes. The EDS analysis revealed a correlation between the ferromagnetic behavior of the tubes and the chromium depletion in the matrix. The chromium depletion in the austenite matrix is the main cause of the magnetization of the carburized tube. The method used currently for the measurement of the carburization of the tubes is confirmed; carburizing evaluation is useful for magnetic flux density measurement. The volume fraction of the carbide increased as the measuring point moved into the carburized side; this was determined from the calculation of the volume fraction in the cross-section image of the tubes. These results are similar to the trends of carburization measurement when those trends were evaluated by measurement of the magnetic flux density.

• 대한간호학회지
• /
• 제24권2호
• /
• pp.175-189
• /
• 1994

This study examined the daily rhythmic patterns of mood in shift workers. Ten rotating shift nurses (shift worker group) were matched with ten non-rotating student nurses (non - shift worker group) working under the same conditions at University Hospital. The subjects completed the Mood Adjective Checkist (MAC) every two or three hours from 6AM to 9-11 PM for six consecutive days. The MAC was constructed by Mansour and conversed the mood factors of Anger - Depression. Happiness, Mental, and Social. These data were analyzed by using Cosinor method. The results are summarized as follows : 1. There was no difference in mean scores for Anger - Depression, Happiness, Mental, and Social mood rhythm between the shift workers and the non - shift workers. 2. There was no difference in the amplitude of Anger - Depression, Happiness and Social mood between the two groups, but the shift workers had a higher amplitude of Mental mood. 3. The acrophases of the Anger - Depression mood were between 1:28 and 2:05, and those of Happiness, Social, and Mental mood were between 12:5 and 15:03 for both groups. There were no differences between the groups. 4. The number of the subjects with statistically significant mean cosinor rhythms for Anger-De-pression and Mental moods were higher in the shift workers than in the non-shift workers, but there were no differences between the shift workers and the non-shift workers in those of Happiness and Mental mood. This study showed that the mod manifested circadian periodicities, and a rapidly rotating shift system did not changed the circadian rhythm of mood. It is expected that this study will facilitate a better understanding of circadian rhythm in mood in the shiftworkers.

• Genomics & Informatics
• /
• 제12권4호
• /
• pp.268-275
• /
• 2014

The harshness of legionellosis differs from mild Pontiac fever to potentially fatal Legionnaire's disease. The increasing development of drug resistance against legionellosis has led to explore new novel drug targets. It has been found that phosphoglucosamine mutase, phosphomannomutase, and phosphoglyceromutase enzymes can be used as the most probable therapeutic drug targets through extensive data mining. Phosphoglucosamine mutase is involved in amino sugar and nucleotide sugar metabolism. The purpose of this study was to predict the potential target of that specific drug. For this, the 3D structure of phosphoglucosamine mutase of Legionella pneumophila (strain Paris) was determined by means of homology modeling through Phyre2 and refined by ModRefiner. Then, the designed model was evaluated with a structure validation program, for instance, PROCHECK, ERRAT, Verify3D, and QMEAN, for further structural analysis. Secondary structural features were determined through self-optimized prediction method with alignment (SOPMA) and interacting networks by STRING. Consequently, we performed molecular docking studies. The analytical result of PROCHECK showed that 95.0% of the residues are in the most favored region, 4.50% are in the additional allowed region and 0.50% are in the generously allowed region of the Ramachandran plot. Verify3D graph value indicates a score of 0.71 and 89.791, 1.11 for ERRAT and QMEAN respectively. Arg419, Thr414, Ser412, and Thr9 were found to dock the substrate for the most favorable binding of S-mercaptocysteine. However, these findings from this current study will pave the way for further extensive investigation of this enzyme in wet lab experiments and in that way assist drug design against legionellosis.

• Restorative Dentistry and Endodontics
• /
• 제19권1호
• /
• pp.231-254
• /
• 1994

Fracture of cusp, on posterior teeth, especially those carious or restored, is major cause of tooth loss. Inappropriate treatments, such as unnecessarily wide cavity preparations, increase the potential of further trauma and possible fracture of the remaining tooth structures. Fracture potential may be directly related to the stresses exerted upon the tooth during masticatory function. The purpose of this study is to evaluate the fracture resistance of tooth, restored with composite resin inlay. In this study, MOD inlay cavity prepared on maxillary first premolar and restored with composite resin inlay. Three dimensional finite element models with eight nodes isoparametric solid element, developed by serial grinding-photographing technique. These models have various occlusal isthmus and depth of cavity, 1/2, 1/3 and 1/4 of isthmus width and 0.7, 0.85 and 1.0 of depth of cavity. The magnitude of load was 474 N and 172 N as presented to maximal biting force and normal chewing force. These loads applied onto ridges of buccal and lingual cusp. These models analyzed with three dimensional finite element method. The results of this study were as follows : 1. There is no difference of displacement between width of occlusal isthmus and depth of cavity. 2. The stress concentrated at bucco-mesial comer, bucco-disal comer, pulpal line angle and the interface area between internal slopes of cusp and resin inlay. 3. The vector of stress direct to buccal and lingual side from center of cavity, to tooth surface going on to enamel. The magnitude of vector increase from occlusal surface to cervix. 4. The crack of tooth start interface area, between internal slop of buccal cusp and resin inlay. It progresses through buccopulpal line angle to cervix at buccomesial and buccodistal comer. 5. The influence with depth of cavity to fracture of tooth was more than width of isthmus. 6. It would be favorable to make the isthmus width narrower than a third of the intercuspal distance and depth of cavity is below 1 : 0.7.

• 한국시뮬레이션학회논문지
• /
• 제18권3호
• /
• pp.147-154
• /
• 2009

본 연구에서는 자동차 도장 공장의 가장 큰 낭비 요소인 상도 공정의 세정 비용의 절감 및 환경 보호를 목적으로 상도 공정 이전의 각 컨베이어 연결점에서의 운영 알고리즘 변경시의 셋업 감소 효과를 시뮬레이션 모델링을 통해 분석하였다. 또한 본 연구의 동기가 된 도장 공정에서의 세정 비용 최소화 프로젝트 및 도장 공장 현황에 대해 설명하였다. 시뮬레이션 결과 컨베이어 연결점에서의 운영 알고리즘 개선시 현재 1.8대의 그룹화 효율을 2.5대 수준으로 향상시킬 수 있음을 알 수 있었다. 본 연구에서 적용한 접근법을 사용할 경우 그룹화 효율 향상에 별도 설비 투자가 필요 없고, CRS(Color Rescheduling Storage) 설치와 병행 적용하여 그룹화 효율을 더욱 향상시킬 수 있는 이점을 가지고 있다.