• Transactions of Materials Processing
• /
• v.31 no.6
• /
• pp.365-375
• /
• 2022

The microstructure and high-temperature plastic deformation behavior of the modified Al-0.7Mn alloy were investigated and compared with the conventional Al-0.3Mn (Al3102) alloy. α-Al (matrix) and Al₆(Mn, Fe) phases were identified in both alloys. As a result of microstructure observation, both alloys showed equiaxed grains, and Al-0.7Mn alloy showed larger grain size and higher Al₆(Mn, Fe) fraction than Al-0.3Mn alloy. High temperature compressive tests, the deformation temperatures of 410℃, 450℃, 490℃, 530℃ and strain rats of 10^-2/s, 10^-1/s, 1/s, 10/s, were conducted using Gleeble equipment. The flow stress values of Al-0.7Mn alloy were higher than that of Al-0.3Mn alloy at all strain rates and temperature conditions. Constitutive equations were presented using the flow stresses obtained from experimental results and the Zener-Hollomon parameter. In the true stress-true strain curves of the two alloys, the experimental and predicted values were in good agreement with each other. Based on the dynamic material model, eutectic deformation maps of Al-0.7Mn and Al-0.3Mn alloys were suggested, and the plastic instability region was presented. The modified Al-0.7Mn alloy showed a wider plastic instability region than that Al-0.3Mn alloy. Based on the process deformation maps, the MPE tube parts could be manufactured through the actual extrusion process using the suggested conditions.

• Journal of Korean Society of Water and Wastewater
• /
• v.37 no.6
• /
• pp.375-382
• /
• 2023

The binary oxide adsorbent using Fe and Mn (Fe-Mn) has been prepared by precipitation method to enhance the removal of phosphate. Different amounts of chitosan, a natural organic polymer, were used during preparation of Fe-Mn as a stabilizer to protect an aggregation of Fe-Mn particles. The optimal amount of chitosan has been determined considering the separation of the Fe-Mn particles by gravity from solution and highest removal efficiency of phosphate (Fe-Mn10). The application of Fe-Mn10 increased removal efficiency at least 15% compared to bare Fe-Mn. According to the Langmuir isotherm model, the maximum uptake (q_m) and affinity coefficient (b) were calculated to be 184 and 240 mg/g, and 4.28 and 7.30 L/mg for Fe-Mn and Fe-Mn10, respectively, indicating 30% and 70% increase. The effect of pH showed that the removal efficiency of phosphate was decrease with increase of pH regardless of type of adsorbent. The enhanced removal efficiency for Fe-Mn10 was maintained in entire range of pH. In the kinetics, both adsorbents obtained 70% removal efficiency within 5 min and 90% removal efficiency was achieved at 1 h. Pseudo second order (PSO) kinetic model showed higher correlation of determination (R²), suggesting chemisorption was the primary phosphate adsorption for both Fe-Mn and Fe-Mn10.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.23 no.8
• /
• pp.627-631
• /
• 2010

ZnS:Mn yellow phosphors doped with Cu for white light emitting diodes were synthesized by solid state reaction method. The optical properties and structures of ZnS:Mn,Cu phosphors were investigated by x-ray diffraction, photoluminescence, and scanning electro microscopy. Photoluminescence excitation spectra originated from $Mn^{2+}$ were ranged from 450 nm to 500 nm. The yellow emission at around 580 nm was associated with $^4T_1{\rightarrow}^6A_1$ transition of $Mn^{2+}$ ions in ZnS:Mn,Cu phosphors. The highest photoluminescence intensity of the phosphors under 405 nm excitation was obtained at Cu concentration of 0.02 mol%. The enhanced photoluminescent intensity in the ZnS:Mn,Cu phosphors was interpreted by energy transfer from Cu to Mn.

• Transactions on Electrical and Electronic Materials
• /
• v.7 no.1
• /
• pp.12-15
• /
• 2006

We present the structural, magnetic, and electrical properties in the (Al,Mn)N films with various Mn concentrations grown by plasma-enhanced molecular beam epitaxy. X-ray diffraction analyses reveal that the (Al,Mn)N films have the wurtzite structure without secondary phases. All (Al,Mn)N films showed the ferromagnetic ordering. Particularly, ($Al_{1-x}Mn_{x}$)N film with x = 0.028 exhibited the highest magnetic moment per Mn atom at room temperature. Since all the films exhibit the insulating characteristics, the origin of ferromagnetism in (Al,Mn)N might be attributed to either indirect exchange interaction caused by virtual electron excitations from Mn acceptor level to the valence band within the samples or a percolation of bound magnetic polarons arisen from exchange interaction of localized carriers with magnetic impurities in a low carrier density regime.

• Journal of the Korean Institute of Navigation
• /
• v.25 no.4
• /
• pp.435-442
• /
• 2001

A new technique to grow a manganese-doped zinc-sulfide(ZnS：Mn) has been proposed using the repeated deposition of the Hot Wall method. The optical characteristics and crystallinity for the ZnS and ZnS：Mn thin films deposited on a quartz glass substrate by the method were investigated. Also, The ZnS：Mn thin film elcetroluminescent devices were fabricated by the method to study luminescence characteristics. All films showed (111)-oriented cubic structure. By the repeated deposition, the deposition rates were decreased, and the optical characteristics and crystalline properties were improved, which clarifies that the method is effective to deposit the thin films with good crystallinity Futhermore, the crystallinity was more improved by the doping of Mn. Only one peak emission at around 585nm originating from Mn luminescent center is observed In the photoluminescent and electroluminescent spectra of ZnS：Mn films and the luminance of the ZnS：Mn-based thin film electroluminescent devices was obtained below 60cd/$m^2$ . The optical and crystalline properties, luminescence characteristics are discussed in terms of the effects of the repeated deposition and Mn-doping.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2005.07a
• /
• pp.386-387
• /
• 2005

anodic deposition법으로 제조된 $MnO_2$와 (Mn, Zn) 산화물의 전도도를 측정하였다. 제조된 Mn 산화물의 조성은 XRD와 EDS를 이용하여 $MnO_2$ 와 Mn 복합산화물로 확인되었다. DV-Xa법으로 계산된 이론 전자상태 계산 결과 천이금속을 첨가하게 되면, Mn 복합 산화물의 에너지 갭이 감소하는 것으로 나타났다. anodic deposition법으로 제조된 $MnO_2$와 Mn 복합 산화물의 전기전도도를 비교하면 천이금속이 첨가된 복합 산화물의 특성이 우수한 것으로 나타났다.

• Journal of the Korean Vacuum Society
• /
• v.8 no.3A
• /
• pp.213-217
• /
• 1999

Fe/MnO multilayers with different bilayer thicknesses were grown by pulsed laser deposition method. Grazing incidence X-ray reflectivity results showed obvious multilayer Bragg peaks implying highly layered samples and, through their analysis, some structural parameters were quantiatively estimated. From the X-ray diffraction peak corresponding to MnO(111), Mn-oxide turned out to be dominantly MnO. To characterize the magnetic properties of $Mn^{+2}$, XMCD were carried out. Magnetic moments of MnO near interfaces were ordered in the opposite direction to those of Fe.

• Proceedings of the Korean Information Science Society Conference
• /
• 2002.10c
• /
• pp.502-504
• /
• 2002

현재, IETF AAA 워킹 그룹에서는 기존 AAA 프로토콜인 RADIUS를 보완 및 확장하여 새로운 프로토콜인 Diameter의 표준화를 진행중이다. Diameter는 기존 전화망에서의 PPP 접속 서비스뿐만 아니라 이동 패킷 서비스를 지원하는 Mobile IP 접속 서비스를 지원하도록 설계되고 있다. AAA 서버는 인증(Authentication), 인가(Authorization) 및 과금(Accounting) 서비스를 사용자에게 제공한다. 이때 Diameter 서버는 MN이 제공하는 credential을 검증함으로써, MN에 대한 인증을 수행한다. MN은 credential을 생성하기 위해서, 홈 Diameter 서버와 MN간에 공유하는 MN-AAA 비밀키와 MAC 알고리즘을 사용한다. 상기키는 이동 가입자가 AAA 서비스를 초기에 요청할 때 발급되는 비밀키이며, Diameter 프로토콜은 상기 비밀키의 재발급 메커니즘을 제공하지 않는다. 메커니즘 부재는 키의 누출의 인한 서비스 도용이 발생한 수 있는 취약점이 있다. 본 논문에서는 키의 누출에 대비한 MN-AAA 키의 재생성 및 재분배 메커니즘을 제안한다. 이를 위해서, Mobile IP 프로토콜 및 Diameter 프로토콜을 확장 및 보완한다.

• Journal of the Korean Chemical Society
• /
• v.38 no.11
• /
• pp.785-791
• /
• 1994

The $Sr_1-_xY_xMnO_3$ (x = 0.0∼1.0) system was synthesized using amorphous citrate process. The stability of various structures and the electronic transport properties of this system were investigated. X-ray diffraction study indicated that the $Sr_1-_xY_xMnO_3$ system has three different structures depending on composition, namely, 4L-hexagonal perovskite (when x is less than 0.3), pseudocubic perovskite (when x is 0.3∼0.7), and hexagonal nonperovskite (when x is larger than 0.7) structures. The structural changes and electronic properties were interpreted based on two factors, i.e., the size of cations and the oxidation state of manganese ion. When the concentration of Y substitution exceeds 30%, the Mn-Mn repulsive interaction dominates over intermetallic attraction, and thus structure changes to pseudocubic perovskite. In perovskite phase the unit cell dimensions increases with increasing $Mn^{3+}$ ions due to yttrium substitution. The band gap of $Sr_{0.9}Y_{0.1}MnO_3$ is greater than that of $Sr_{0.5}Y_{0.5}MnO_3$. The greater band gap of $Sr_{0.9}Y_{0.1}MnO_3$ indicates that the 4L-hexagonal structure is more stabilized than cubic perovskite due to the Mn-Mn bond.

• Animal Bioscience
• /
• v.34 no.11
• /
• pp.1811-1821
• /
• 2021

Objective: A trial was conducted to investigate the effects of supplemental levels of Mn provided by organic and inorganic trace mineral supplements on growth, tissue mineralization, mineral balance, and antioxidant status of growing broiler chicks. Methods: A total of 500 male chicks (8-d-old) were used in 10-day feeding trial, with 10 treatments and 10 replicates of 5 chicks per treatment. A 2×5 factorial design was used where supplemental Mn levels (0, 25, 50, 75, and 100 mg Mn/kg diet) were provided as MnSO₄·H₂O or MnPro. When Mn was supplied as MnPro, supplements of zinc, copper, iron, and selenium were supplied as organic minerals, whereas in MnSO₄·H₂O supplemented diets, inorganic salts were used as sources of other trace minerals. Performance data were fitted to a linearbroken line regression model to estimate the optimal supplemental Mn levels. Results: Manganese supplementation improved body weight, average daily gain (ADG) and feed conversion ratio (FCR) compared with chicks fed diets not supplemented with Mn. Manganese in liver, breast muscle, and tibia were greatest at 50, 75, and 100 mg supplemental Mn/kg diet, respectively. Higher activities of glutathione peroxidase and superoxide dismutase (total-SOD) were found in both liver and breast muscle of chicks fed diets supplemented with inorganic minerals. In chicks fed MnSO₄·H₂O, ADG, FCR, Mn balance, and concentration in liver were optimized at 59.8, 74.3, 20.6, and 43.1 mg supplemental Mn/kg diet, respectively. In MnPro fed chicks, ADG, FCR, Mn balance, and concentration in liver and breast were optimized at 20.6, 38.0, 16.6, 33.5, and 62.3 mg supplemental Mn/kg, respectively. Conclusion: Lower levels of organic Mn were required by growing chicks for performance optimization compared to inorganic Mn. Based on the FCR, the ideal supplemental levels of organic and inorganic Mn in chick feeds were 38.0 and 74.3 mg Mn/kg diet, respectively.