• Journal of the Earthquake Engineering Society of Korea
• /
• v.24 no.1
• /
• pp.29-37
• /
• 2020

This study is to investigate the effect of a retrofitted reinforced concrete frame with non-seismic details strengthened by embedded steel moment frames with an indirect joint, which mitigates the problems of the direct joint method. First, full-scale experiments were conducted to confirm the structural behavior of a 2-story reinforced concrete frame with non-seismic details and strengthened by a steel moment frame with an indirect joint. The reinforced concrete frame with non-seismic details showed a maximum strength of 185 kN at an overall drift ratio of 1.75%. The flexural-shear failure of columns was governed, and shear cracks were concentrated at the beam-column joints. The reinforced concrete frame strengthened by the embedded steel moment frames achieved a maximum strength of 701 kN at an overall drift ratio of 1.5% so that the maximum strength was about 3.8 times that of the specimen with non-seismic details. The failure pattern of the retrofitted specimen was the loss of bond strength between the concrete and the rebars of the columns caused by a prying action of the bottom indirect joint because of lateral force. Furthermore, methods are proposed for calculation of the specified strength of the reinforced concrete frame with non-seismic details and strengthened by the steel moment frame with the indirect joint.

• Computers and Concrete
• /
• v.6 no.5
• /
• pp.357-376
• /
• 2009

In the design of concrete columns, it is important to provide some nominal flexural ductility even for structures not subjected to earthquake attack. Currently, the nominal flexural ductility is provided by imposing empirical deemed-to-satisfy rules, which limit the minimum size and maximum spacing of the confining reinforcement. However, these existing empirical rules have the major shortcoming that the actual level of flexural ductility provided is not consistent, being generally lower at higher concrete strength or higher axial load level. Hence, for high-strength concrete columns subjected to high axial loads, these existing rules are unsafe. Herein, the combined effects of concrete strength, axial load level, confining pressure and longitudinal steel ratio on the flexural ductility are evaluated using nonlinear moment-curvature analysis. Based on the numerical results, a new design method that provides a consistent level of nominal flexural ductility by imposing an upper limit to the axial load level or a lower limit to the confining pressure is developed. Lastly, two formulas and one design chart for direct evaluation of the maximum axial load level and minimum confining pressure are produced.

• Structural Engineering and Mechanics
• /
• v.58 no.2
• /
• pp.259-276
• /
• 2016

Lead-rubber bearings (LRBs) have been used worldwide in seismic design of buildings and bridges owing to their stable mechanical properties and good isolation effect. We have investigated the effectiveness of LRBs in framed underground structures on controlling structural seismic responses. Nonlinear dynamic time history analyses were carried out on the well-documented Daikai Station, which collapsed during the 1995 Hyogoken-Nanbu earthquake. Influences of strength ratio (ratio of yield strength of LRBs to yield strength of central column) and shear modulus of rubber on structural seismic responses were studied. As a displacement-based passive energy dissipation device, LRBs reduce dynamic internal forces of framed underground structures and improve their seismic performance. An optimal range of strength ratios was proposed for the case presented. Within this range, LRBs can dissipate maximum input earthquake energy. The maximum shear and moment of the central column can achieve more than 50% reduction, whereas the maximum shear displacement of LRBs is acceptable.

• Korean Journal of Applied Biomechanics
• /
• v.23 no.2
• /
• pp.149-157
• /
• 2013

In the present study, we aimed to elucidate how muscle strength and activity are affected by movement pattern(bilateral [BLM] & unilateral movement [ULM]) and movement velocity($0^{\circ}$/s, $60^{\circ}$/s, $120^{\circ}$/s) at maximum effort, and to elucidate the relationship between a left/right asymmetry and bilateral deficit. A total of 18 healthy males participated in the study. Each participant performed maximum knee extension bilaterally and unilaterally while the EMG and moment were recorded, and then the relationships between the asymmetry and bilateral deficit were analyzed. The peak moments for the isokinetic motion at $60^{\circ}$/s and $120^{\circ}$/s and overall muscle activities of lower extremity were significantly reduced for the BLM in comparison to the ULM. And though the asymmetry in ULM were maintained during BLM at all velocities, the bilateral deficits at the velocity of $0^{\circ}\acute{y}$/s and $120^{\circ}\acute{y}$/s were significantly correlated with increased asymmetries of muscle strength in ULM. In conclusion, the reduction in the muscle strength exhibited in bilateral knee extension was shown to arise partially from a reduction in muscle activity, and left/right asymmetry was found to be associated with mechanical reduction in bilateral movement. These findings suggest that training aimed at increasing muscle strength must involve methods and strategies intended to reduce left/right asymmetry.

• Korean Journal of Applied Biomechanics
• /
• v.31 no.4
• /
• pp.227-233
• /
• 2021

Objective: The purpose of this study was to in this study. The maximum grip force of the elderly hand was measured using a custom-designed grasping apparatus mounted with five three-component force transducers. The Jebsen-Tayler hand function test and Purdue Pegboard test were performed to evaluate the dexterity of the hand. Method: Twenty-six elderly women participated in the left hand between the maximum grip force and the Jebsen-Taylor hand function test results (r=-.513, p=.007). A significant correlation was also shown in the hand maximum grip force and the hand Purdue Pegboard results (r=.514, p=.007). However, no significant correlation was found in the right hand. Results: We found a significant correlation investigate the relationship between hand grip strength and hand dexterity in the elderly. Conclusion: Our findings in the current study support the theory of 'Strength-dexterity complementariness' which states that improvement in dexterity is associated with the grip force strength.

• Textile Coloration and Finishing
• /
• v.34 no.3
• /
• pp.197-206
• /
• 2022

The purpose of this study was to confirm the optimal spinning conditions for PLA (Polylactic acid) as a fiber forming polymer. According to the melt spinning test results of PLA, the optimal spinning temperature was 258℃. However, it needs to note that relatively high pack pressure was required for spinning at 258℃. At an elevated temperature, 262℃, mono filament was broken easily due to hydrolysis of PLA at a higher temperature. In case of fiber strength, it was confirmed that the draw ratios of 2.7 to 3.3 were optimal for maximum strength of melt spun PLA. Above the draw ratio, 3.3, the strength of the PLA fibers was lowered. It was presumed that cleavage of the PLA polymer chain over maximum elongation. The heat setting temperature of GR (Godet roller) showed that the maximum strength of the PLA fibers was revealed around 100℃. The degree of crystallinity and the strength of the PLA fibers were decreased above 100℃. The optimal take-up speed (Spinning speed) was around 4,000m/min. Thermal analysis of PLA showed 170℃ and 57℃ as Tm (melting temperature) and Tg (glass transition temperature), respectively.

• Physical Therapy Rehabilitation Science
• /
• v.12 no.2
• /
• pp.201-205
• /
• 2023

Objective: Resistance exercise is a necessary element to improve quality of life, and measurement and evaluation of muscle strength provide important information for prescription and management of rehabilitation and exercise programs. This study analyzed the correlation between direct and indirect 1RM for isokinetic maximum torque of the knee joint in order to provide useful information in the field of exercise programs. In addition, the flexion-extension ratio and the difference in left-right deviation were verified. Design: A cross-sectional study Methods: The subjects of this study were 33 healthy adult men and women without medical problems who participated in the health exercise class program at S University in Seoul. The correlation between isokinetic maximum torque and direct and indirect 1RM was analyzed, and a dependent t-test was performed to analyze the flexion-extension ratio and left-right deviation. Results: There was a high correlation between the isokinetic maximum torque and direct and indirect 1RM, and no statistically significant difference was shown between the test methods in the analysis of the flexion-extension ratio and left-right deviation. Conclusions: Isokinetic muscle function measuring equipment is expensive, so it is difficult to use it in local exercise rehabilitation and training sites. Through this study, it was found that direct and indirect 1RM isokinetic maximum torque showed a high correlation, and there was no difference in evaluating muscle function such as flexion-extension ratio and left-right deviation. Therefore, it is considered that the muscle function evaluation using 1RM in general field can be usefully utilized.

• Transactions of the Korean Society of Machine Tool Engineers
• /
• v.15 no.1
• /
• pp.63-69
• /
• 2006

This study deals with the friction welding of A2024- T6 to A6061- T6; The friction time was variable conditions under the conditions of spindle revolution of 2000rpm, friction pressure of 50MPa, upset pressure of 100MPa, and upset time of 5.0seconds. Under these conditions, the microstructure of weld interface, tensile fracture surface and mechanical tests were studied, of friction weld, and so the results were as follows. 1. When the friction time was 1.5seconds under the conditions, the maximum tensile strength of the friction weld happened to be 292MPa, which is $94.2\%$ of the base material's tensile strength(310MPa). At the same condition, the maximum shear strength was 2l2MPa, which is equivalent to $103\%$ of the base material's shear strength (205MPa). 2. At the same condition, the maximum vickers hardness was Hv 146 at A2024- T6 nearby weld interface, which is higher Hv3 than condition of the friction time 0.5seconds, and the maximum vickers hardness was Hvl20 from weld interface of A6061-T6, which is higher Hv28 then base material's. 3. The results of microstructure analysis show that the structures of two base materials have fractionized and rearranged along a column due to heating and axial force during friction, which has affected in raising hardness and tensile strength.

• The Journal of Korean Academy of Orthopedic Manual Physical Therapy
• /
• v.28 no.3
• /
• pp.9-19
• /
• 2022

Background: The study objectives were to investigate the effect of Kinesio taping, Mulligan taping on push-off-test and maximum grip strength in elite men's artistic gymnast with wrist impingement syndromes. Methods: The subjects of this study were 18 wrist impingement syndromes men's artistic gymnast and randomly assigned to a Kinesio taping group, Mulligan taping group. Weight-bearing wrist pain and Muscle strength were assessed with push-off-test (POT) and the maximum grip strength (MGS). Results: As a result of the research, there were no significant difference in POT in pre and post group in the Kinesio taping (p>.05). But Mulligan taping group were significant difference in POT (p<.05). In comparison after intervention between each other groups, there was a no significant difference on (p<.05), but no significant difference on post (p>.05). there were significant difference in MGS in both pre and post group in the Kinesio taping and Maximum Grip Strength (p<.05). In comparison after intervention between each other groups, there was a no significant difference on pre (p<.05), but no significant difference on post (p>.05). Conclusion: This results suggests that Mulligan taping are encouraged due to effects on pain, Muscle strength increase in elite men's artistic gymnast with wrist impingement syndromes.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.9 no.3
• /
• pp.45-54
• /
• 2009

This study was developed the metallic plate for bone fixation in the neurosurgery and general surgery and plates has a finn place in bone operating and treatment. The plates can be realized to bending strength and stiffness for strength estimation. Maximum point of bending curves has a bending point(P) with maximum load which to applied nearly 0.2% offset displacement. The device's sizing has a ${\Phi}13$ and ${\Phi}18$, and algorithm of strength estimation compared a plate(${\Phi}13$, ${\Phi}18$, ${\Phi}13-{\Phi}18$). The bending strength of the curved metallic plate has to evaluate maximum of a 311N, 387N, 410N, 474N. When a displacement preserve with a load, tensile stress through to press a plate is 274N, 324N, 382N, 394N. The algorithm of strength estimation can be used to support estimation of bending strength and stiffness. Their tool bring to settlement in the new basic algorithm for evidence with varied adjustment.