• Journal of Energy Engineering
• /
• v.24 no.4
• /
• pp.124-129
• /
• 2015

An experimental study was performed estimating COP(Coefficient of Performance) of air-conditioning cycle using inverter scroll compressor with and without $Al_2O_3$ nano particle. All experiments were done for various compressor speeds from 1000~4000 rpm and used the inverter controller called CANDY to change the compressor rpm. The air-conditioning cycle components in the apparatus were used as same with components of YF hybrid car. To estimate the COP, this study measured the temperature and pressure at inlets and outlets of compressor, condenser, and evaporator. And also measured the compressor input power using Powermeter. Through the experiments, the maximum error to estimate COP was shown about ${\pm}6.09%$ at 3500rpm. The COP of refrigeration cycle with $Al_2O_3$ nano-particle was similar with that of the base cycle without nano-particle between 1000~3000 rpm of the compressor speed. But, This study showed that the COP of the cycle with $Al_2O_3$ over 3000 rpm of the compressor speed was higher than that of the base cycle due to the higher heat transfer rate increased in the evaporator from the higher oil flow rate inside the cycle as well known. Those results can be used the basic and fundamental data to design the air-conditioning cycle using inverter scroll compressor with $Al_2O_3$ nano particle.

• Journal of Environmental Impact Assessment
• /
• v.20 no.4
• /
• pp.497-507
• /
• 2011

This research studied human health risk assessment of benzene from industrial complexes of Chungcheong Province (Seosan industrial complex) and Jeonla Province (Iksan industrial complex and Yeosoo industrial complex). The residents near the industrial complexes areas can be often exposed to volatile organic compounds (e.g., benzene, toluene, xylenes) through a number of exposure pathways, including inhalation of the organic pollutant via various environmental matrices (air, water and soil), contaminated water, and soil intake. Benzene is well known to be a common carcinogenic and toxic compound that is produced from industrial and oil refinery complexes. In this study, a number of samples from water, air, and soil were taken from the residential settings and public school zones located near the industrial complex sites. Based on the carcinogenic risk assessment, the risk estimates were slightly above $10{\times}10^{-6}$ at all three industrial sites. According to deterministic risk assessment, inhalation was the most important route. The distribution of benzene in the environment would be dependent on vapor pressure, and the physical property influencing the extent of the potential risks. Non-carcinogenic risk assessment of benzene shows that the values of Hazard Index(HI) were much lower than 1.0 at all industrial complexes. Therefore, benzene was not a cause of concern in terms of non-carcinogenic risk posed to the residents near the sites. When compared to probabilistic risk assessment, the CTE(central tendency exposure) cancer risk values of deterministic risk assessment were close to the mean values predicted by the probabilistic risk assessment. The RME(reasonable maximum exposure) values fell within the range of 95% to 99.9% estimated by the probabilistic risk assessment. Since the values of carcinogenic risk assessment were higher than $10{\times}10^{-6}$, further detailed monitoring and refined risk assessment for benzene may be warranted to estimate more reliable and potential inhalation risks to receptors near the industrial complexes.

• KSBB Journal
• /
• v.13 no.6
• /
• pp.706-717
• /
• 1998

Enzymatic synthesis of fructose-based sugar fatty acid esters, such as methyl fructoside oleic acid mono and diester, was investigated using methyl fructoside as a sugar starting material. For the production of methyl fructoside fatty acid monoester by solvent process, 2-methyl 2-propanol was found to be a god reaction medium resulting a higher yield and productivity due to its high sugar solubility. The yield and productivity of methyl fructoside oleic acid monoester were 70% and 12.6g/L-hr, respectively, when molar ratio of methyl fructoside, initial concentration of methyl fructoside, enzyme(Novozym 435) content, and reaction temperature were 3:1, 200g/L, 1%(w/v), and $60^{\circ}C$, respectively. Methyl fructoside oleic acid diester was prepared by lipase-catalyzed diacylation of methyl fructoside and oleic acid in the solvent-free process. Maximum yield of 98% and productivity of 140g/L-hr were achieved when molar ratio(methyl fructoside and oleic acid) of 1:2 enzyme content of 10%(w/v) and reaction temperature of $70^{\circ}C$ were applied for the operating conditions under a reduced pressure of 20∼200 mmHg.

• Journal of the Korean Geotechnical Society
• /
• v.20 no.3
• /
• pp.107-117
• /
• 2004

This paper is to investigate the reinforcing effects of newly devised Tire-cell mat made of waste tires in sand. Parametric study on number of connection bolts between Tirecells, relative density of sand, embedded depth, number of reinforced layers and width of Tirecell mat was made by using plate loading tests. It is found that the number of connection bolt was enough to maintain the given pressure. The bearing capacity ratio(BCR), which is defined as the rate of ultimate bearing capacity of reinforced soil to that of unreinforced soil, is the highest at the lowest density. And the reinforcing effect can be obtained in case of embedded depth within 1.0B, where B is loading width. Also settlement reduction is the highest at the lowest density of sand. The effect of number of Tirecell reinforced layers with 0.4B to 0.5B interval is limited to 2 layers and further reinforcing effects can not be obtained beyond 3 layers. Especially, the bearing capacity increased remarkably at 1 layer of reinforcement and the degree of increase was small from 1 layer to 2 layers of reinforcement. The effect of mat width of Tirecell was not significant because of high stiffness of Tirecell although the maximum bearing capacity was shown at the 2.0B mat width and the reinforcing effects of Tirecell, in general, was prominent compared with those of commercial Geoweb.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.14 no.2
• /
• pp.119-125
• /
• 2008

The aim of this study was to determine the characteristics of wave transformation in the shallow water of the Nakdong River estuary due to variations in air pressure, air temperature, wind speed, and wind direction. We analyzed the correlation between weather factors and wind waves in offshore regions near Geoje Island and the Nakdong River estuary in April and May 2007. The weather and wind wave data were obtained from the automatic ocean observation buoy near Geoje Island operated by the Korean Meteorological Administration (KMA). For the estuary region, the wind wave information was the result of field observations, and weather data were obtained from the Busan Meteorological Station. Field observations of water waves in April and May showed that the maximum wave height decreased by about 2.2 m. M oreover, wave height decreased significantly by about 1.3 m due to the reduction in wave energy caused by the water waves propagating from Geoje buoy to the Nakdong River estuary. We conclude that offshore or wind waves coming into the Nakdong River estuary showed considerable height variation due to the prevailing weather conditions, especially wind speed and direction. In particular, headwinds tended to decrease the wave size in inverse proportion to the wind speed.

• Polymer(Korea)
• /
• v.35 no.5
• /
• pp.467-471
• /
• 2011

PET bottle is manufactured by blow molding the preform, which is molded by injection molding. The neck part of the preform of PET bottle for juice or grain-based beverage is crystallized before blowing to improve heat resistance at the entrance of the bottle. However, residual stress, developed during injection molding of preform, prevents the crystallization. In order to release the residual stress in the preform, the preform is annealed after the injection molding. If the residual stress is reduced by optimizing the injection molding conditions of preform the annealing time would be shortened. In this study, the optimum conditions for minimizing the residual stress and increasing dimensional accuracy of the injection molded preform are suggested through CAE analysis. In order to optimize the molding conditions, minimizing residual stress and shrinkage, computer simulations have been carried out with help of design of experiment scheduling. Injection temperature, initial packing pressure and filling time were selected for control parameters. Residual stress was affected by injection temperature and filling time. Shrinkage was affected by injection temperature. It was found that maximum residual stress, distribution of residual stress and shrinkage were decreased by 22%, 40% and 25%, respectively at an optimum molding condition compared with the results of previous molding condition.

• The Journal of Korean Physical Therapy
• /
• v.12 no.1
• /
• pp.101-112
• /
• 2000

The aim of this study is to compared the cerebral palsy children with normal children in the exercise and cardio vascular ability after this study as the fundamental data fer mating programs for the cerebral palsy children. The test of this study is about twenty girls, the control group of the normal children(n=10) and the experiment group of cerebral palsy children(n=10). They were studied in four aspects which were the anthropometry, the medical check in the rest, the physical fitness or exercise roads test and the change of the target heart rate during exercise. The result were as follows : 1. The characteristic of the physical type : The control group is higher than the experiment group in the standing height and the body weight but their's little difference between them (p<0.05). The control group is lower than the experiment group in the body fat. 2. The characteristic of the medical check in the rest : The control group is higher than the experiment group in the vital capacity and flood expiratoryvolume one second. The control group is higher that the experiment group in the blood pressure of systolic and Diastolic. There's little difference between them(p<0.01). The control is lower than the experiment group in the heart pulse rate. There's little difference between them(p<0.005). 3. The characteristic of basic physical strength evaluation : The experiment group is the lowest dynamic muscular endurance, balance, agility and endurance which need to move the body with weight. The control group is much higher than the experiment group in the flexibility and muscle strength(Back strength). There's no difference between them(p<0.05). 4. The characteristics of the exercise stress last : The control group is higher than the experiment group in the endurance, the maximum of oxygen intake, endurance level and the out take of calory. There's little difference between them(p<0.01). 5. The characteristic of the change of the target heart rate during exercise : The control group is lower than the experiment group exchange of target heart rate, There's no difference them.

• Journal of the Korean Chemical Society
• /
• v.35 no.3
• /
• pp.211-218
• /
• 1991

A series of samples in the $Nd_{-x}Sr_{x}CoO_{3-y}$ system (x = 0.00, 0.25, 0.50, 0.75 and 1.00) have been produced by heating the reactants at 1200${\circ}$C under atmospheric pressure. The solid solutions were analysed by X-ray diffraction spectra, thermal analysis, and SEM micrographs. X-ray powder diffraction assigns the compositions of x = 0.00, 0.25, 0.50 and 0.75 to the cubic system and the composition of x = 1.00 to the orthorhombic system. The reduced lattice volume is increased with increasing x values in the system. The mole ratio of $Co^{4+}$ or ${\tau}$ values are determined by the Iodometric titration method and are maximum at the composition of x = 0.50. The magnetic measurement shows that a ferromagnetism is appeared in the compositions of x = 0.00, 0.25, 0.50 and 0.75 and then an antiferromagnetism in the composition of x = 1.00. The measurement of the electrical conductivity shows that the semiconductivity is appeared in the composition of x = 0.00, 0.25 and 1.00 and the metallic conductivity in the composition of x = 0.50 and 0.75. The magnetic and electrical properties of the samples are discussed with the nonstoichiometric chemical formulas.

• Clean Technology
• /
• v.18 no.2
• /
• pp.209-215
• /
• 2012

The performance and removal efficiencies of a pilot scale biofilter were estimated by using ammonia and hydrogen sulfide as the odorous gases. Expanded polyurethane foam coated with powdered activated carbon and zeolite was used as a biofilm supporting medium in the biofilter. Odorous gases from the sludge thickener of a municipal wastewater treatment plant were treated in the biofilter for 10 months and the inlet ammonia and hydrogen sulfide concentrations were 0.1-1.5 and 2-20 ppmv, respectively. The removal efficiencies reached about 100% at the empty bed retention time (EBRT) of 3.6-5 seconds except for the adaptation periods. The pressure drop of the biofilter caused by the gas flow was also low that the maximum attained was 31 mm $H_2O$ during the operation. Its stability was confirmed in the long term due to the fact that the biofilter and the polyurethane medium had a minimum plugging and compression. The microbial community on the medium is critical for the performance of the biofilter especially the distribution of ammonia oxidizing bacteria (AOB) and sulfur oxidizing bacteria (SOB). The distribution of Nitrosomonas sp. (AOB) and Thiobacillus ferroxidans (SOB) was confirmed by FISH (fluorescence in situ hybridization) analysis. The longer the operation time, the more microbial population observed. Also, the medium close to the gas inlet had more microbial population than the medium at the gas outlet of the biofilter.

• Clean Technology
• /
• v.19 no.4
• /
• pp.416-422
• /
• 2013

In environmental friendly aspects, the synthesis of glycerol carbonate from glycerol using carbon monoxide and oxygen gases which were produced in petrochemical plants was studied. The oxidative carbonylation of glycerol under batch reaction system was performed on parameter conditions such as effect of various metals (Cu, Pd, Fe, Sn, Zn, Cr), oxidizing agents, mole ratio of carbon monoxide to oxygen, catalyst amount, solvent types, reaction temperature and time and dehydrating agents. In particular copper chloride catalysts showed the excellent activities, and the glycerol carbonate yields over CuCl and $CuCl_2$ catalysts were the maximum of 44% and 64%, respectively at the following reaction conditions: solvent as nitrobenzene, mole ratio of 1:3:0.15 (glycerol:carbon monoxide:catalyst), mole ratio of 2:1 (carbon monoxide:oxygen), the total pressure of 30 bar at 413 K for 4 hr. It was found that reactivity were significantly different depending on the oxidation number of Cu catalysts, and oxygen plays an important role as oxidizing agents in producing H2O during oxidation reaction after carbonylation of glycerol.