• 환경위생공학
• /
• 제24권2호
• /
• pp.17-30
• /
• 2009

In Iksan city, there have been a lot of complaints caused by offensive odor from residents living near the public environmental infrastructures and the Iksan industrial complex. To solve these problems, it is important to know the present condition of odor pollution level in these areas, the emission characteristics of malodorous gases in temporal and spatial variations in addition to meteorological components, and the facilities of major sources emitting malodorous compounds. The objectives of this study is to make the odor monitoring network for 20 people who lived and worked in areas where the environmental infrastructures and the Iksan industrial complex are located and their neighboring areas for six months from June 1st to October 31st in 2008 in Iksan and to monitor the temporal and regional frequency and characteristics of odor intensity using direct olfactory methods. As a result of odor monitoring, the highest frequency of sensed odor per month and 20 people for six months was found to be 107 in July, followed by 84 in September, 80 in August, 54 in June, 38 in October, respectively. Odor intensity trend showed a regional trend in the decreasing order of Dongsan-dong, Busong-dong, and Palbong-dong. Odor was widely perceived from night through next morning and considered as the sense of excreta, chemicals, sewage, compost, waste, etc. When high odor intensity was sensed, there were constant meteorological characteristics: relative humidity was 80~90%, wind speed was less than 0.5~1 m/sec, and main wind directions were from the east, the southeast, and the south.

• Preventive Nutrition and Food Science
• /
• 제13권3호
• /
• pp.219-224
• /
• 2008

In this study, we investigated changes in some physico-chemical and biochemical properties of Kimchi during fermentation and storage. After fermenting Kimchi at $15^{\circ}C$ for 23, 36, 40, 44, and 60 hrs during the first week, we stored it at $-1^{\circ}C$ in a Kimchi refrigerator until the end of 8th week. The pH of samples fermented for 36 hr, 40 hr, 44 hr and 60 hr sharply decreased during the first seven days and then slowly decreased. Acidities of samples fermented for 36 hr, 40 hr and 44 hr sharply increased for the first seven days. According to measured changes of lactic acid bacteria number, samples fermented for 60 hr revealed the largest augmentation in the number of lactobacilli for the first seven days. The $\gamma$-aminobutyric acid (GABA) content of the sample fermented for 40 hr was the most superior, with an early increase and maintenance of GABA content, which maintained a maximum 20 mg per 100 g of Kimchi sample on the seventh, fourteenth, and twenty eighth days. These results suggest that relatively enhanced levels of GABA in Kimchi samples can be produced and maintained by controlling the fermentation and storage processes, as with the 40 hr fermented sample conditions.

• 센서학회지
• /
• 제5권5호
• /
• pp.69-77
• /
• 1996

Pt/Cr 이중층과 E-beam으로 증착된 산화막으로 구성된 발열체의 발열특성과 열처리 온도에 따른 Pt/Cr 이중층의 전기적, 구조적 특성을 살펴보았다. E-beam으로 증착된 산화막을 갖는 발열체의 표면 방사율(${\varepsilon}$)은 0.5임을 열전대와 I.R. Thermo-Vision System을 통하여 확인할 수 있었다. 한편 열처리전 Pt/Cr의 면저항은 Cr의 두께와는 무관한데, 이는 백금과 크롬의 계면에 형성된 산화크롬에 의한 것으로 사료되며, 열처리 온도가 증가함에 따라 Cr의 외부확산이 증대되고, Pt(220)면의 결정립이 성장함을 AES 분석결과와 SEM 촬영, XRD 분석을 통하여 알 수 있었다. 열처리 온도에 따른 특성 분석결과, $500^{\circ}C$에서 열처리한 Pt/Cr 이중층이 안정된 결정구조를 갖음을 XRD, AES 분석결과로 확인할 수 있었다.

• 한국주조공학회지
• /
• 제14권3호
• /
• pp.233-239
• /
• 1994

The effects of solid solution treatment and aging in the properties of Cu-0.32wt%Be-1.35wt%Co alloy was gravity die casted and forged were investigated in order to examine the optimum heat treatment conditions for production of high conductivity mold material. The optimum properties for mold material were obtained under the conditions which were solid solution treated at $930^{\circ}C$ for 1 hour and aged at $430^{\circ}C$ for 2hours.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1995년도 하계학술대회 논문집 C
• /
• pp.1114-1116
• /
• 1995

P/N(CuO/ZnO) Heterojunction gas sensors were made by 2-step sintering methods and its gas sensing property was measured by varying the injected gases and the operating temperatures. As the applied voltage was increased in air ambients, the current-voltage characteristics shown the ohmic properties. However, when the CO gas ambients, 500 ppm at $200^{\circ}C$, the current-voltage characteristics behaves like a rectifying diode s after 3 mins later and its conduction mechanism is discussed qualitatively for the first times.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1995년도 하계학술대회 논문집 C
• /
• pp.1209-1212
• /
• 1995

This paper presents a capacitive humidity sensor using porous silicon layers formed tom the anodization of p-type silicon in HF solution. The upper electrodes consist of many aluminum strips over porous silicon, between which the porous silicon is etched away. The sensor showed a good sensitivity(20pF/%RH) and lineaity in the range of 40%RH$\sim$80%RH, a hysteresis of ${\pm}2%$ RH, and a slow transient response. These preliminary resluts show that futher improvement can still be expected.

• 대한기계학회논문집A
• /
• 제21권7호
• /
• pp.1081-1088
• /
• 1997

The purpose of this work is to investigate the working limit of carbon steel and forging condition of cold forging. The fracture criteria which was proposed by Oyane and Osakada was used. Compression test, hardness study and tension test by Oyane's creteria, microstructure study by Osakada's were carried out. The results were compared with each other. It was found that working limit on compressive hydrostatic stress is increased in comparison with that of tensile stress field and can be forecasted the fracture limit of closed cold forging.

• 한국지능시스템학회:학술대회논문집
• /
• 한국퍼지및지능시스템학회 2007년도 춘계학술대회 학술발표 논문집 제17권 제1호
• /
• pp.394-396
• /
• 2007

본 논문은 레이더를 통해 입력받은 데이터를 분석하여 같은 물체에 관한 데이터를 구분하는 방법을 제시한다. 큰 영역을 감시하는 레이더에 비해 영역이 좁을 때 레이더는 한 물체에 대해서 물체 형태에 따라 데이터가 들어오게 된다. 이 데이터들은 같은 물체인지 아닌지 구분이 없어서 응용된 알고리즘을 적용하기 힘들다. 따라서 응용된 알고리즘을 적용하기 전 하나의 물체에 대한 데이터의 그룹핑 작업이 필요하다. 본 논문에서 그룹핑 방법을 제시하며 실제 도로에서 취득한 데이터를 가지고 시뮬레이션을 하였다.

• International Journal of Automotive Technology
• /
• 제7권7호
• /
• pp.821-826
• /
• 2006

This paper describes a rollover index (RI)-based rollover mitigation control (RMC) system. A rollover index which indicates an impending rollover has been developed by a roll dynamics phase plane analysis. The rollover index is calculated using the roll angle, the roll rate, the lateral acceleration and time to wheel lift (TTWL). A differential braking control law based on a 2-D bicycle model has been designed using the direct yaw control (DYC) method. An RMC threshold has been determined from the rollover index. The performance of the RMC scheme and the effectiveness of the proposed rollover index are illustrated using a vehicle simulator.

• 한국정밀공학회지
• /
• 제28권1호
• /
• pp.11-18
• /
• 2011

A worm screw is widely used in a geared motor unit for motion conversion from rotation to linear. For mass production of a high quality worm, the current rolling process is substituted with the milling process. Since the milling process enables the integration of all operations of worm manufacturing on a CNC(Computer Numerical Control) lathe, productivity can be remarkably improved. In this study, the tooling system for side milling on a CNC lathe to improve machinability is developed. However, the cutting tool-workpiece interference is important factors to be considered for producing high quality worms. For adaptability of various worms machining, the tool-workpiece interference simulation system based on a tool-tip trajectory model is developed. The developed simulation system is verified through several kinds of worms and experimental results.