• 멤브레인
• /
• 제6권2호
• /
• pp.86-95
• /
• 1996

본 연구에서는1축 회전판형 한외여과막 모듈의 순수 투과율 예측모델과 기름 에멀션의 분리 특성 및 투과율 예측모델을 유도하였다. 1축 RDM은 한외여과막(UOP사, 직경 0.22m)으로 제작된 회전판막을 장착하여 $25^{\circ}C$에서 압력, 각속도($\omega$), 농도 변화에 따라 분리특성을 조사하였다. 회전판막의 각속도가 0에서 52.36rad/s로 증가할수록 회전판내 유체가 받는 원심력에 의한 압력 강하와 분리막 표면의 미끄럼 흐름에 의한 압력 강하로 순수 투과율은 최대 각속도에서 3.9% 감소하였다. 원심력과 미끄럼 흐름에 의한 압력 강하는 선속도(${\omega}r$)의 자승에 비례하였다. 회전판의 각속도가 52.36에서 2.62rad/s로 감소할 때 5% 절삭유의 투과율은 30.16% 감소하였고 농도가 낮을수록 막회전과 투과율에 미치는 영향은 적었다. 절삭유의 투과율(J; $kg/m^{2} \cdot s$)은 회전에 의한 압력 강하를 고려한 유효압력차($\Delta P_{T}$ ; Pa), 벌크농도($C_{B}$; %), 선속도($\omega$r; m/s) 등에 영향을 받으며 실험 결과에 저항 모델을 적용하여 다음과 같은 식을 유도하였다.

• 전기화학회지
• /
• 제4권3호
• /
• pp.113-117
• /
• 2001

탄소계 전극을 사용하는 EDLC(Electric Double Layer Capacitor)용의 축전용량과 충방전속도는 전해질의 종류, 충방전 조건 그리고 탄소계 물질의 물리화학적 성질에 따라 크게 달라질 수 있다. 이에 본 연구에서는 dip coating method에 의해 제조된 EDLC용 활성탄소 전극에서 유기 전해질의 종류를 달리하여 충방전 실험과 전기화학적인 실험을 시행하였다. 또한 충전전류밀도와 방전전류밀도의 변화에 따른 비축전 용량의 변화를 조사하였고, 최적 유기전해질의 조건에서 leakage current 특성, 자가방전 특성 그리고 시간전압곡선을 기존의 $1M-Et_4NBF_4/PC$와 비교하였다 활성탄, 소전극으로 비표면적이 $2000m^2/g$인 MSP-20을 사용하고 유기전해질로는 $1M-LiPF_6/PC-DEC(1:1)$를 사용한 EDLC에서 130 F/g 정도의 우수한 비축전 용량을 나타내었고 저항면에서도 가장 낮은 수치를 나타내었다 $1M-LiPF_6/PCDEC(1:1)$를 사용한 EDLC는 15분동안 0.0004A의 낮은 leakage current와 100시간 경과 후 0.8V의 우수한 자가 방전 특성 그리고 IR-drop이 적은 선형의 시간-전압곡선을 보여주었다.

• Corrosion Science and Technology
• /
• 제8권2호
• /
• pp.74-80
• /
• 2009

The high alkaline property in the concrete pore solution protects the embedded steel in concrete from corrosion due to aggressive ions attack. However, a continuous supply of those ions, in particular, chlorides altogether with a pH fall in electrochemical reaction on the steel surface eventually depassivate the steel to corrode. To mitigate chloride-induced corrosion in concrete structures, finely grained mineral admixtures, for example, pulverized fuel ash (PFA), ground granulated blast furnace slag (GGBS) and silica fume (SF) have been often advised to replace ordinary Portland cement (OPC) partially as binder. A consistent assessment of those partial replacements has been rarely performed with respect to the resistance of each binder to corrosion, although the studies for each binder were extensively looked into in a way of measuring the corrosion rate, influence of microstructure or chemistry of chlorides ions with cement hydrations. The paper studies the behavior of steel corrosion, chloride transport, pore structure and buffering capacity of those cementitious binders. The corrosion rate of steel in mortars of OPC, 30% PFA, 60% GGBS and 10% SF respectively, with chloride in cast ranging from 0.0 to 3.0% by weight of binder was measured at 7, 28 and 150 days to determine the chloride threshold level and the rate of corrosion propagation, using the anodic polarization technique. Mercury intrusion porosimetry was also applied to cement pastes of each binder at 7 and 28 days to ensure the development of pore structure. Finally, the release rate of bound chlorides (i.e. buffering capacity) was measured at 150 days. The chloride threshold level was determined assuming that the corrosion rate is beyond 1-2 mA/$m^3$ at corrosion and the order of the level was OPC > 10% SF > 60% GGBS > 30% PFA. Mercury intrusion porosimetry showed that 10% SF paste produced the most dense pore structure, followed by 60% GGBS, 30% PFA and OPC pastes, respectively. It was found that OPC itself is beneficial in resisting to corrosion initiation, but use of pozzolanic materials as binders shows more resistance to chloride transport into concrete, thus delay the onset of corrosion.

• Corrosion Science and Technology
• /
• 제15권3호
• /
• pp.141-146
• /
• 2016

By using Ni-Cr and Co-Cr alloys, porcelain fused to metal (PFM) samples were prepared to examine the interface and the surface corrosion behavior. The potentiodynamic polarization analysis showed that the corrosion current density of Co-Cr alloy ($1.61{\times}10^{-6}A/cm^2$) was three times lower than that of Ni-Cr alloy ($4.83{\times}10^{-6}A/cm^2$) at room temperature. A dental prosthesis consisting of the porcelain fused to Ni-Cr alloy extracted from a patient after approximately four years of usage was examined to assess its resistance to corrosion. OM and SEM images of the metal part revealed a typical pitting corrosion. As compared to porcelain fused to Ni-Cr alloy having a thick layer (${\sim}10{\mu}m$) of oxide at the interface, a relatively thin oxide layer (less than $5{\mu}m$) was formed on Co-Cr alloy, indicating that the interface between Co-Cr alloy and porcelain may have a better adhesion strength than the interface between Ni-Cr alloy and porcelain.

• Journal of Electrochemical Science and Technology
• /
• 제3권3호
• /
• pp.123-134
• /
• 2012

The electrochemical performance of positive pole grids of lead-acid batteries made of Pb-0.08%Ca-1.1%Sn alloys without and with 0.1 wt% of each of Cu, As or Sb and with 0.1 wt% of Cu, As and Sb combined was investigated by electrochemical methods in 4.0 M $H_2SO_4$. The corrodibility of alloys under open-circuit conditions and constant current charging of the positive pole, the positive pole gassing and the self-discharge of the charged positive pole were studied. All impurities (Cu, As, Sb) were found to decrease the corrosion resistance, $R_{corr}$ after 1/2 hour corrosion, but after 24 hours an improvement in $R_{corr}$ was recorded for Sb containing alloy and the alloy with the three impurities combined. While an individual impurity was found to enhance oxygen evolution reaction, the impurities combined significantly inhibition this reaction and the related water loss problem was improved. Impedance results were found helpful in identification of the species involved in the charging/discharging and the self-discharge of the positive pole. Impurities individually or combined were found to increase the self-discharge during polarization (33-68%), where Sb containing alloy was the worst and impurities combined alloy was the least. The corrosion of the positive pole grid in the constant current charging was found to increase in the presence of impurities by 5-10%. Under open-circuit, the self-discharge of the charged positive grids was found to increase significantly (92-212%) in the presence of impurities, with Sb-containing alloy was the worst. The important result of the study is that the harmful effect of the studied impurities combined was not additive but sometimes lesser than any individual impurity.

• 한국전자파학회논문지
• /
• 제20권2호
• /
• pp.174-182
• /
• 2009

본 논문에서는 삼각형 패치와 서브 패치를 이용하여 국내 UHF RFID 대역에서 근거리장 영역과 원거리장 영역을 겸용하여 사용할 수 있는 안테나를 제안하였다. 제안된 안테나는 FR-4 기판에 마이크로스트립 패치로 인쇄되어 대량생산이 용이한 평면 구조이며, UHF RFID 주파수 대역(912 MHz)에서 동작하도록 설계하였다. 삼각형 패치를 이용하여 정면방향에서 원형편파 특성을 가지고 동작하며 서브 패치를 삽입하여 근거리장 영역에서 강하고 균일한 수직 자계를 형성 할 수 있도록 하였다. 측정 결과 제작된 안테나는 개구면에서 3 cm 떨어진 근거리장 영역에서 -25 dBA/m 이상의 수직 자계를 형성하며, 정면방향 원거리장에서 AR<3 dB의 원형편파를 복사하며 6 dBi의 복사 이득을 보였다.

• 한국재료학회지
• /
• 제10권9호
• /
• pp.607-611
• /
• 2000

고밀도 DRAM에서 박막 커패시터로의 적용을 위해 Zr이 첨가된 (Ba(sub)1-x, Sr(sub)x)TiO$_3$<원문차조> 박막이 r.f. magnetron sputter-ing 법에 의해 제조되었다. 증착된 박막들은 다결정질 구조를 보였으며 증착압력이 감소함에따라 Zr/Ti의 비가 현저히 증가하였으며 본 연구에서는 얻어진 박막들은 100kHz에서 380∼525의 유전상수값을 나타냈다. 전압에 따른 커패시턴스와 분극량의 변화는 이력특성을 크게 보이지 않아 상유전상으로 형성되었음을 보였다. 누설전류밀도는 증착압력이 감소함에 따라 작아지는 경향을 보였고 10mTorr이상에서 증착된 박막의 경우 200kV/cm의 전계에서 10(sup)-7∼10(sup)-8A/$\textrm{cm}^2$의 차수를 갖는 누설전류밀도를 보여 본 연구에서 제조된 (Ba(sub)1-x, Sr(sub)x)(Ti(sub)1-x, Zr(sub)x)O$_3$<원문참조>박막은 고밀도 DRAm을 위한 커패시터에의 적용가능성을 보였다.

• Progress in Superconductivity
• /
• 제13권2호
• /
• pp.105-110
• /
• 2011

SQUID sensor-based ultra low-field magnetic resonance apparatus with ${\mu}T$-level measurement field requires a strong prepolarization magnetic field ($B_p$) to magnetize its sample and obtain magnetic resonance signal with a high signal-to-noise ratio. This $B_p$ needs to be ramped down very quickly so that it does not interfere with signal acquisition which must take place before the sample magnetization relaxes off. A MOSFET switch-based $B_p$ coil driver has current ramp-down time ($t_{rd}$) that increases with $B_p$ current, which makes it unsuitable for driving high-field $B_p$ coil made of superconducting material. An energy cycling-type current driver has been developed for such a coil. This driver contains a storage capacitor inside a switch in IGBT-diode bridge configuration, which can manipulate how the capacitor is connected between the $B_p$ coil and its current source. The implemented circuit with 1.2 kV-tolerant devices was capable of driving 32 A current into a thick copper-wire solenoid $B_p$ coil with a 182 mm inner diameter, 0.23 H inductance, and 5.4 mT/A magnetic field-to-current ratio. The measured trd was 7.6 ms with a 160 ${\mu}F$ storage capacitor. trd was dependent only on the inductance of the coil and the capacitance of the driver capacitor. This driver is scalable to significantly higher current of superconducting $B_p$ coils without the $t_{rd}$ becoming unacceptably long with higher $B_p$ current.

• 전기화학회지
• /
• 제4권2호
• /
• pp.41-46
• /
• 2001

황산과 황산구리 수용액을 전해질로 사용하여 다공성 그물구조 금속을 전기화학적으로 제조하였으며, 이때 균질 전착에 영향을 미치는 첨가제 PEG, MPS의 영향에 대해 살펴보았다. 분극실험과 기공의 평균 직경이 $250{\mu}m$의 그물구조 전극을 여러장 적층하여 throwing power를 정량화 한 결과, PEG의 경우 분극 초기에 전극에서 탈착됨으로써 오히려 throwing power를 감소시키고 MPS는 500ppm까지 용액 중 첨가량의 증가와 함께 throwing power를 향상시키는 결과를 보였다 또한 MPS와 PEG가 동시에 혼합된 용액에서는 MPS의 효과가 우선적으로 나타나며 PEG의 효과는 무시할 정도였다 그러나 MPS의 첨가는 전착층의 균열을 유도하여 기계적 강도에 좋지 못한 영향을 미치며 균열을 피하려면 50ppm 이하가 적정함을 SEM 관찰을 통해 확인할 수 있었다.

• 한국세라믹학회지
• /
• 제48권6호
• /
• pp.487-492
• /
• 2011

The effect of the application of lanthanum strontrium manganite and yttria-stabilized zirconia (LSM-YSZ) nano-composite fabricated by pulsed laser deposition (PLD) as a cathode of solid oxide fuel cell (SOFC) is studied. A gradient-structure thin-film cathode composed of 1 micron-thick LSM-YSZ deposited at an ambient pressure ($P_{amb}$) of 200 mTorr; 2 micron-thick LSM-YSZ deposited at a $P_{amb}$ of 300 mTorr; and 2 micron-thick lanthanum strontium cobaltite (LSC) current collecting layer was fabricated on an anode-supported SOFC with an ~8 micron-thick YSZ electrolyte. In comparison with a 1 micron-thick nano-structure single-phase LSM cathode fabricated by PLD, it was obviously effective to increase triple phase boundaries (TPB) over the whole thickness of the cathode layer by employing the composite and increasing the physical thickness of the cathode. Both polarization and ohmic resistances of the cell were significantly reduced and the power output of the cell was improved by a factor of 1.6.