• Journal of Electrical Engineering and Technology
• /
• v.10 no.3
• /
• pp.1154-1161
• /
• 2015

This paper presents a semi-lumped balun transformer using conventional PCB process and its design theory and geometry for the maximally flat response and wide bandwidth using magnetically coupled LC resonators. The proposed balun is comprised of two pairs of coupled resonators which share one among three LC resonators. It provides an identical magnitude and phase difference of 180° between two balanced ports with DC isolation and an impedance transformation characteristic. Theoretical design and analysis were performed to optimize the inductance and capacitance values of proposed balun device for obtaining the wide bandwidth and maximally flat response in its pass-band. Three balun transformers with a center frequency of 500 MHz were demonstrated for proving the concept of design proposed. They were fabricated by using lumped chip capacitors and planar inductors embedded into a conventional 4-layered PCB substrate. They exhibited a maximum magnitude difference of 0.8 dB and phase difference within 2.4 degrees.

• The Transactions of the Korean Institute of Electrical Engineers C
• /
• v.55 no.4
• /
• pp.161-165
• /
• 2006

In this paper, we developed HPF (high pass filter) consists of lumped LC components to decrease the noises that are detected in PD (partial discharge) measuring test, and adapted it to field test. We tested it under laboratory circumstances like the fields, and measured the phase change properties of detected signal in UHF sensor with Lemke Probe and oscilloscope (TDS-3054, Tektronix). As a result, we obtained available data showing the decrease of noises in the experiments with the developed HPF from the joint box of 22.9kV distribution line. The result can be adapted to prevent the degeneration of the XLPE power cable, and to observe and diagnosis the underground power transmission cable at the ultra-high voltage.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.22 no.1
• /
• pp.12-20
• /
• 1997

Physical interconnect such as Printed Circuit Board(PCB) traces introduces new challenges for parameter extraction and delay calculation for high-speed system design. PCB traces are dominated by frequency dependent LC propagation which makes precharacterization difficult for all possible configurations. Moreover, simulating the transient behavior of the trace for noise and delay analysis requries the combined used of a variety of models and techniques for efficiently handling lossy, low-loss, frequency dependent, and coupled transmission lines together with lumped elements. In this paper we explain how the frequency dependence caused by ground plane proximity and skin effects can be modeled using the adstracted models. These abstracted (lumped) models are SPICE-compatible and can be simulated in time-domain, along with precharacterized lumped parasitic elements and nonlinear driver and load models.

• Proceedings of the KIEE Conference
• /
• 2008.09a
• /
• pp.224-226
• /
• 2008

In this paper, we developed HPF (high pass filter) consisted of lumped LC components to decrease the noises that are detected in PD (partial discharge) measuring test, and adapted it to field test.

• Proceedings of the KIEE Conference
• /
• 2008.09a
• /
• pp.239-242
• /
• 2008

In this paper, we developed HPF (high pass filter) consisted of lumped LC components to decrease the noises that are detected in PD (partial discharge) measuring test, and adapted it to field test. We tested under laboratory circumstances like the fields, and measured the phase change properties of detected signal in UHF sensor with Lemke probe and oscilloscope (TDS-3054, Tektronix).

• Proceedings of the KIEE Conference
• /
• 2007.04b
• /
• pp.65-67
• /
• 2007

In this paper, we developed HPF (high pass filter) consisted of lumped LC components to decrease the noises that are detected in PD (partial discharge) measuring test, and adapted it to field test.

• Proceedings of the Korea Society for Simulation Conference
• /
• 2001.10a
• /
• pp.205-208
• /
• 2001

A lumped electrical circuit is an approximate representation of the field within a curtain frequency range. The finite element modelling is a synonym of the equivalent circuit. The electric conduction field and electric potential wave field have been modelled by an admittance network and an LC low-pass filter network. Here in the present paper, the equivalent magnetic circuit representation is created for a magnetostatic field by the finite element modelling in two dimension.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.21 no.2
• /
• pp.129-135
• /
• 2010

In this paper, we propose and demonstrate a new four-port BPSK direct conversion receiver based on $0.18\;{\mu}m$ CMOS technology for K-band applications. The proposed direct conversion receiver is composed of two active combiners, an lumped LC balun, two power detectors and an analog decode. The designed direct conversion receiver is successfully demodulated BPSK signal with 40 Mbps in the K-band.

• Journal of electromagnetic engineering and science
• /
• v.17 no.2
• /
• pp.71-75
• /
• 2017

A dual-band tunable-slot-type ground radiation antenna is proposed. The feeding structure consists of a coplanar waveguide and a lumped capacitor to excite currents for first- and second-order resonant modes of the ground. The resonant frequencies of both bands are controlled using a series combination of a capacitor and an inductor. The proposed design may be an attractive choice for mobile devices owing to its compact geometry and tunable operating frequencies. The measurement and simulation results of the proposed antenna show good agreement, indicating good impedance matching and radiation performance.

• Proceedings of the KIEE Conference
• /
• 2007.04b
• /
• pp.68-71
• /
• 2007

In this paper, we developed HPF (high pass filter) consisted of lumped LC components to decrease the noises that are detected in PD (partial discharge) measuring test, and adapted it to field test. We tested under laboratory circumstances like the fields, and measured the phase change properties of detected signal in UHF sensor with Lemke probe and oscilloscope (TDS-3054, Tektronix).